OmniConnect ISDN Internet Access Device Quick Install Guide PN 613-10791-00 Rev.
Copyright ”1999 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086 USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
Regulatory Compliance Information Agency Approvals The following agency approvals have been obtained for the LanEdge OmniConnect ISDN internet access device in the areas of Safety, EMC and PTT (Public Telephone and Telegraph). Safety UL 1950, CSA 22.2 No.
Regulatory Compliance Information FCC Class B Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
OmniConnect ISDN Quick Install Guide If the telephone company requests information on what equipment is connected to their lines, inform them of: 1. The telephone number to which this unit is connected. 2. The ringer equivalence number. 3. The USOC jack required [RJ11C] 4. The FCC Registration Number [xxxUSA-xxxxx-xx-e] In the event of equipment malfunction, an authorized agent should perform all repairs.
Regulatory Compliance Information The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Number of all the devices does not exceed 5.
OmniConnect ISDN Quick Install Guide Operating Conditions for the United Kingdom The following apply to the LanEdge OmniConnect ISDN internet access device when used in the UK: 1. Interconnection directly, or by way of other apparatus, of ports marked U, S/ T, and Phone with ports marked or not so marked may produce hazardous conditions on the network, and that advice should be obtained from a competent engineer before such a connection is made. 2.
Table of Contents Regulatory Compliance Information ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïLLL Agency Approvals.................................................................................................................. iii CE Marking Directive ........................................................................................................... iii EMC Information .............................................................................................
7DEOHýRIý&RQWHQWV Appendix A LanEdge OmniConnect ISDN Installation Guide Feedback ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïëì Appendix B Technical Support Fax Order ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïëê x
Chapter 1 Introduction Overview The OmniConnect ISDN Internet Access Device connects users on a local Ethernet LAN to the Internet over Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) lines. The illustrations below show the front and rear panels of the OmniConnect ISDN.
Introduction Work sheet Before you begin installation, use the following OmniConnect work sheet and note the listed information for use during configuration. OmniConnect ISDN Work Sheet ‰ ISDN line is installed and accessible.
OmniConnect ISDN Quick Install Guide Topology Plan your topology including the OmniConnect. The sample topology below shows the ISDN OmniConnect used for a group of PC users in a small office network. In this example, four 10 Mbps PC NICs and a telephone are connected to the OmniConnect.
Chapter 2 Installation Use this section to verify your package contents, position the device, and configure it.
Installation To place your LanEdge product, see the steps that follow: ‰ “To wall mount a LanEdge product” on page 6 ‰ “To place a single LanEdge product on a desktop” on page 6 ‰ “To interlock a group of LanEdge products on a desktop” on page 7 To wall mount a LanEdge product 1. Do not install the rubber feet or bumpers if you are wall mounting the product. If you previously installed the square rubber bumpers, remove them using the following step. (The round rubber feet need not be removed.
OmniConnect ISDN Quick Install Guide To interlock a group of LanEdge products on a desktop You can interlock two or more LanEdge products. Interlocking is a physical placement so that the products occupy only one footprint on the desktop. Interlocking does not connect the devices in any other way. If you are installing a FastPrint Server, place it as the base (bottom) unit, otherwise, place the OmniConnect as the base unit. 1. Select the base unit and place it upside down on a work surface.
Installation 3. Place the first LanEdge unit on the desktop as the base. If you are installing a FastPrint Server, place it as the base (bottom) unit, otherwise, place the OmniConnect as the base unit. 4. Pry off the interlock cap at each corner of the unit: From the side of the unit, insert the tip of a small straight-slot screwdriver into the opening of the interlock cap. Press down on the screwdriver to pry the cap off. 5.
OmniConnect ISDN Quick Install Guide Plug the AC power adapter provided with the unit into the correct AC power source for this adapter. Next connect the DC cable from the adapter into the OmniConnect DC input. Verify that the Power LED lights (see LED table). 5. Verify that the Ethernet LEDs light green (see LED table). For troubleshooting techniques, refer to your Installation Guide. You are now ready to configure and setup the OmniConnect. To continue, see “Verify your PC Configuration” on page 10.
Installation Verify your PC Configuration 1. Verify that your NIC and network driver are correctly installed; the Ethernet LED on the OmniConnect and the Link LED on the NIC should be lit. If necessary, refer to the installation manual for the NIC and the PC. 2. Verify that the TCP/IP protocol is installed and configured on each PC connected to the OmniConnect. For details concerning this, refer to the “TCP/IP Network Installation and Configuration” section of your Installation Guide.
OmniConnect ISDN Quick Install Guide Enter Password Access to the OmniStart configuration utility is protected by a password. The default password is omni. Enter omni in the dialog box titled Password and press Enter or Next> to advance to the next screen. To change the password from the default value, click the check box 'Select this box to change the password' and then enter the new password in the New Password and Confirm New Password dialog boxes and press Next>.
Installation Internet Service Provider Setup The Internet Service Provider Setup screen is used to enter the Internet Service Provider (ISP) login and password information. The Internet Service Provider (ISP) provides you with a login name, password and phone number. Enter the login information provided in this screen. The OmniConnect will use this information to establish a connection with the Internet Service Provider. Remember to enter any numbers required to access an outside area code or city code.
OmniConnect ISDN Quick Install Guide ISDN Parameters Setup The ISDN Parameters Screen is used to enter ISDN configuration information. When an ISDN line is ordered, the ISDN dial-tone provider assigns an ISDN switch for the ISDN connection, the switch software configuration and the ISDN phone numbers (Directory Number) and SPID Numbers. Use this screen to enter all these parameters. Please note that in certain cases, fewer than two SPIDs or ISDN Phone Numbers may be provided.
Installation The Enable Data Over Voice (DOV) dialog box should be checked if the ISDN line is provisioned for Data Over Voice. If the Disable Data Over Voice (Data Only) dialog box is checked, the OmniConnect will request Data Only bearer services. The default is Disable Enable Data Over Voice. Once this information has been entered, pressing the Next > button will advance the setup process to the next screen. Pressing the Advanced >>> button will allow the setting of advanced ISDN parameters.
OmniConnect ISDN Quick Install Guide The default DHCP address is 192.168.1.1. Once this information is entered, press the Next > button to proceed to the next screen. ISDN Parameter Verification The ISDN Parameter Verification screen verifies the configuration of the ISDN line, ISDN switch settings, the ISP information and the DNS information. Each of these parameters are checked for the ISDN line.
Installation ISDN Configuration checks to see if the ISDN line is correctly connected to a live ISDN line and if the ISDN switch parameter settings (switch type, Directory Number and SPID) are correct. If any of these are not true, ISDN Configuration returns a failure. ISP Configuration checks to see if the ISP information (login, password and phone number) are correct and a login is possible. If any of these are not correct, this test returns a failure.
OmniConnect ISDN Quick Install Guide Advanced Setup Options (Finish) Once the user has reached this Advanced Setup Options screen, all the minimum parameters for a simple installation of the OmniConnect have been configured. Press the FINISH button on this screen to exit the setup program. The OmniConnect is ready for use! The various options located on this screen may be used to setup various advanced options.
Installation LanEdge Publications Visit our technical publications website at: www.alliedtelesyn.
OmniConnect ISDN Quick Install Guide For Technical Support or Service Location Phone Fax Technical Support Address TS1@alliedtelesyn.com CompuServe Go ALLIED FTP Server $GGUHVVã JDWHZD\ïFHQWUHïFRPý>ORZHUFDVHýOHWWHUV@ /RJLQã DQRQ\PRXVý>ORZHUFDVHýOHWWHUV@ 3DVVZRUGã \RXUýHðPDLOýDGGUHVVý>UHTXHVWHGýE\ýWKHýVHUYHUýDWý ORJLQ@ For Information Regarding Allied Telesyn International, Corp. Allied Telesyn International, Corp.
Appendix A LanEdge OmniConnect ISDN Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of this guide.
Appendix B Technical Support Fax Order Name __________________________________________________________________ Company _______________________________________________________________ Address ________________________________________________________________ City ________________________ State/Province_______________________________ Zip/Postal Code ___________________ Country_______________________________ Phone _______________________________Fax________________________________ Incident Summary Model number
