Owner manual

ManualsBrandsAllied Telesis ManualsComputer HardwareAT-VIEW PLUS 3.2 DEVICE MANAGEMENT

AT-V

IEW PLUS 3.2

EVICE MANAGEMENT GUIDE

PN 613-50665-00 Rev C Page 1 of 294

Summary of content (294 pages)

PAGE 1
AT-VIEW PLUS 3.
PAGE 2
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Copyright (c) 1998-2005 Allied Telesis K. K. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, K. K. Microsoft is a registered trademark of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.
PAGE 3
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT TABLE OF CONTENTS Basic Operations ............................................................................................................11 Common operations on the main window...................................................................12 Menu for stacked devices ...........................................................................................13 Port selection dialog box....................................................................
PAGE 4
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT RMON Menu...............................................................................................................52 Port Menu ...................................................................................................................53 Stacking Menu ............................................................................................................54 AT-8300GB Series .......................................................................
PAGE 5
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PPP Menu ..................................................................................................................94 Port Menu ...................................................................................................................97 AT-AR300 and AT-AR300L............................................................................................98 Main Window .................................................................................
PAGE 6
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Routing Menu ...........................................................................................................121 Bridge Menu .............................................................................................................121 Port Menu .................................................................................................................122 AT-AR720 ...............................................................................
PAGE 7
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9400 Series ............................................................................................................155 Main Window ............................................................................................................155 Agent Menu ..............................................................................................................156 Bridge Menu ............................................................................
PAGE 8
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window ............................................................................................................189 Agent Menu ..............................................................................................................191 Routing Menu ...........................................................................................................192 Bridge Menu ...............................................................................
PAGE 9
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window ............................................................................................................250 Agent Menu ..............................................................................................................251 Status Menu .............................................................................................................252 AT-MCF112 Family .........................................................................
PAGE 10
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules .........................
PAGE 11
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT This document describes the operations and menus specific to particular Allied Telesyn models of managed devices. For module-independent information, refer to the AT-View Plus Device Manager User's Guide. Basic Operations AT-View Plus Device Manager's main window shows the main panel of the target device. It has both common and device-specific menus on its menu bar.
PAGE 12
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Common operations on the main window Right clicking on a port Port Right clicking on a port opens a pull-down menu specific to the device. Selecting a menu item opens another window and lets you view and edit MIB information related to the port. You can also access the same menu from the menu bar. RS-232 Terminal Port Right clicking on an RS-232 port opens a pull-down menu and lets you choose how to log into the agent.
PAGE 13
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Menu for stacked devices If the target is a stacked device, some menus have extra subitems to specify a single device in the stack.
PAGE 14
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port selection dialog box When you select a menu item acting on ports, a dialog box opens to let you select ports. Check the target ports and click OK. Note - If you select multiple ports, it may take some time for data to be displayed. Select Port dialog box Port status colors Port status is shown by its color. Port speed is also displayed in the port image.
PAGE 15
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Utilization Utilization is calculated by the following formula.
PAGE 16
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8000 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8000 Series.
PAGE 17
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8012M-QS AT-8016F/MT PN 613-50665-00 Rev C Page 17 of 294
PAGE 18
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8016F/SC AT-8016F/ST PN 613-50665-00 Rev C Page 18 of 294
PAGE 19
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8024 AT-8024GB PN 613-50665-00 Rev C Page 19 of 294
PAGE 20
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8024M AT-8026FC PN 613-50665-00 Rev C Page 20 of 294
PAGE 21
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8026T AT-8088/MT PN 613-50665-00 Rev C Page 21 of 294
PAGE 22
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8088/SC Device Manager LEDs for AT-8000 Series LED State Description PWR Green The switch is receiving power. MASTER Orange Gray DUPLEX Green Orange The switch is the master switch of an enhanced stack. The switch is a slave switch or is not a member of an enhanced stack. The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 23
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Setting the 'Active Protocol Version' to 'STP' and 'Spanning Tree Status' to 'enabled' will set the Port State parameter of disabled ports to 'blocking'. As a result, port images for disabled ports will turn yellow. Note - Setting the 'Active Protocol Version' to 'RSTP' and 'Spanning Tree Status' to 'enabled' will set the Port State parameter of inactive ports and disabled ports to 'blocking'.
PAGE 24
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Reset Resets the switch. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 25
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 26
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays the port's spanning tree parameters. Note - Setting a port's Port parameter to 'disabled' does not automatically set the Port State parameter under Detail Info to 'disabled'. As a result, the port's image may not turn red as expected. Note - The current firmware version accepts values in the range [0-255] inclusive for the Port Priority parameter regardless of the active spanning tree protocol version.
PAGE 27
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT the MIB variable window. To see the change reflected in the MIB variable window, the Mirroring Destination Port parameter should be set to a non-zero value. Stacking Menu From the Stacking menu, you can perform enhanced stacking from any AT-8000 Series master switch. Stacking Info Displays information about the switch's mode. This is also the menu where you can perform enhanced stacking.
PAGE 28
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124 This section describes AT-View Plus Device Manager menus and operations specific to the AT8124 switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-8124 Device Manager LEDs for AT-8124 LED State Description PWR Green The switch is receiving power. DUPLEX Green Gray PN 613-50665-00 Rev C The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 29
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device or log into the CLI using telnet. System Info Displays basic system information, including system name, location, contact and description. Network Info Displays network-related information such as the device's IP address, and the default gateway address. Firmware Info Displays the version of the software running on the managed device.
PAGE 30
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT RMON Menu From the RMON menu you can view and edit the RMON MIB. Note - Since there may be a large quantity of RMON data, it may take some time for the information to appear. Statistics Displays traffic statistics about the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log.
PAGE 31
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port.
PAGE 32
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124XL (V2) This section describes AT-View Plus Device Manager menus and operations specific to the AT8124XL (V2) switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-8124XL (V2) Device Manager LEDs for AT-8124XL (V2) LED State Description PWR Green The switch is receiving power. DUPLEX Green Orange PN 613-50665-00 Rev C The port is operating in full-duplex mode.
PAGE 33
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the System Contact, System Name, and System Location parameters but truncates them to 64 characters. NULL values are not accepted.
PAGE 34
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch's ports. RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table.
PAGE 35
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Attempting to modify the Port Speed and Mode parameter from 'auto sense' to '1Gbps half-duplex' or '1Gbps full-duplex' will result in the following: • • An error message: "The error occurred with 'Set' operation. Error: gen Error" Port Speed and Mode parameter value changing to '100Mbps half-duplex'. Note - The current firmware version does not allow the Port Bridge ID parameter to be configured.
PAGE 36
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8200XL Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8216FXL/SC and AT-8224XL switches.
PAGE 37
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8224XL Device Manager LEDs for AT-8200XL Series LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating at full-duplex mode. The port is operating at half-duplex mode.
PAGE 38
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version appends a period '.' and the value of the Default Domain Name parameter to the value of the System Name parameter. Firmware Info Displays the firmware version of the switch. Network Info Displays network-related information such as the addresses of the default gateway and the agents. Manager Address Info Displays the IP address of the management station. Device Info Displays general information about the switch.
PAGE 39
Allied Telesyn • • • • • • AT-VIEW PLUS DEVICE MANAGEMENT Fan Speed 3 3.3V Power 2.5Va Power 2.5Vb Power 2V Power CPU Temperature Reset Resets the switch. Console Settings Displays the current settings of the console. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Note - The current firmware version is unable to display the AT-8216FXL/SC device image in the Omega web management session interface.
PAGE 40
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 41
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version allows active ports to be disabled. However, the disabled ports' Port Link State parameter retains the value 'on-line'. Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.
PAGE 42
Allied Telesyn • • AT-VIEW PLUS DEVICE MANAGEMENT The current firmware version does not allow the Port Speed and Mode parameter of the AT-A17 expansion module ports to be set to 'auto sense'. When the Port Speed and Mode parameter of an AT-A18 expansion module port is set to 'auto sense' and the port is connected to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.
PAGE 43
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324 This section describes AT-View Plus Device Manager menus and operations specific to the AT8324 switch.
PAGE 44
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Supports up to 8 stacked AT-8324 switches. Device Manager LEDs for AT-8324 LED State Description PWR Green The switch is receiving power. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - Please refer to Uplink Modules for the operations and behaviour of the expansion modules installed on these devices.
PAGE 45
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 46
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version is unable to retrieve the correct information for the History Control Table. As a result, the following error message appears: "Failed to get MIB data." Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 47
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version (AT-S25 v2.0.2) supports atiStackSwitch.mib v1.0. However, AT-View Plus Device Manager supports atiStackSwitch.mib v2.10. As a result, the following additional port parameters will appear: • • • • Port MDIO Port HOL Limit Port Back Pressure Limit Port STP State These parameters are defined in v2.10 but will return 'noSuchName.' because they do not exist in v1.0.
PAGE 48
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Expansion Module Notes • • • • • Expansion module ports cannot be enabled/disabled. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: gen Error". The Port Speed and Mode parameter of the 100/1000Base-T port on the AT-A14 expansion module can only be set to 'auto'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".
PAGE 49
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324SX This section describes AT-View Plus Device Manager menus and operations specific to the AT8324SX switch.
PAGE 50
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8324SX Supports up to 4 stacked switches.
PAGE 51
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8324SX LED State Description PWR Green The switch is receiving power. RPS Green Redundant power is ON. Gray Redundant power is OFF. DUPLEX Gray STACK ID The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode. Green The switch's position in the switch stack. Note - When multiple units of AT-8324SX are stacked together, port numbering is continuous.
PAGE 52
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information, such as the forwarding database and spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 53
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Note - The current firmware version does not allow Port Menu to support the Class of Service. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 54
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination. IGMP Snooping Displays the current state of IGMP Snooping and allows reconfiguration. Note - Valid MIB Set values for the IGMP Report Delay parameter should range from 5 to 30. However, the current firmware version does not allow it to be set to a value greater than 10.
PAGE 55
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8300GB Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8300GB Series.
PAGE 56
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8326GB PN 613-50665-00 Rev C Page 56 of 294
PAGE 57
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT The AT-8326GB supports up to 6 AT-8326GB stacked switches or any of the following mixed stack combinations of AT-8326GB and AT-8350GB switches: • • • • Two AT-8326GB switches and one AT-8350GB switch Two AT-8326GB switches and two AT-8350GB switches Three AT-8326GB switches and one AT-8350GB switch Four AT-8326GB switches and one AT-8350GB switch Note - When 3 or more AT-8326GB devices are stacked together, expect the twisted pair port image of Port 26 on th
PAGE 58
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8300GB Series LED State Description PWR Green The switch is receiving power. STACK ID Green The switch's position in the switch stack. DUPLEX Green The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode.
PAGE 59
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT DHCP Info Displays DHCP information including the DHCP System Group and DHCP Timer Group. Manager Address Info Displays the IP address of the management station. Reset Resets the switch. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.
PAGE 60
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 61
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port. QoS Displays QoS parameters and allows enabling of QoS status and setting priority queue. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source and destination. IGMP Snooping Displays the current state of IGMP Snooping and allows reconfiguration.
PAGE 62
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 This section describes AT-View Plus Device Manager menus and operations specific to the AT8400 switch.
PAGE 63
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8400 PN 613-50665-00 Rev C Page 63 of 294
PAGE 64
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8401 Management Module LED State Description FAN A Green FAN TRAY A is installed and is operating correctly. Gray FAN TRAY A is not installed. Green FAN TRAY B is installed and is operating correctly. Gray FAN TRAY B is not installed. FAN B MASTER Green RPS The switch is the master of an enhanced stack. Gray The switch is either a slave switch of an enhanced stack or the switch is not a member of an enhanced stack.
PAGE 65
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Info Displays network-related information such as the addresses of the default gateway and the agents. Note - The current firmware version does not allow the DNS Server and Default Domain Name parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error.". Chassis Info Displays chassis information including the firmware information.
PAGE 66
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as spanning tree status and spanning tree version. Note - When setting the Spanning Tree Status parameter to 'enabled', connection to the AT-8400 is temporarily lost.
PAGE 67
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Note - Ports are numbered continuously from top to bottom, across all installed line cards, starting from the leftmost line card all the way through the rightmost line card. This applies to the following submenu options: • • • • Utilization Interface Info -> Standard Error Statistics -> Standard Spanning Tree Info Utilization Displays the port's utilization information.
PAGE 68
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state and port's source list. Note - Valid MIB Set values for the Port Mirroring Configuration Entry Status parameter are 'active', 'not in service' and 'destroy'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.".
PAGE 69
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 Line Cards This section describes the AT-8400 Line Cards supported by AT-View Plus Device Manager. If line cards are installed on the AT-8400 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image. • • • • AT-8411 AT-8412 AT-8413 AT-8414 AT-8411 AT-8411 LED State Description DUPLEX Green The port is operating in full-duplex.
PAGE 70
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8412 AT-8412/MT AT-8412/SC LED State Description DUPLEX Green The port is operating in full-duplex. Note - The current firmware version does not allow the Port Flow Control parameter of ports on the AT-8412/MT and AT-8412/SC line cards to be set to 'auto'. Attempting to set this parameter to 'auto' will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".
PAGE 71
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8413 AT-8413GB/T LED State Description DUPLEX Green The port is operating in full-duplex. Orange The port is operating in half-duplex. Note - A GBIC image is always visible on the GBIC slot of the AT-8413GB/T line card image even if there is no GBIC physically present in the slot.
PAGE 72
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8414 AT-8414/SC AT-8414/ST LED State Description DUPLEX Green The port is operating in full-duplex. Orange The port is operating in half-duplex. Note - The Port Negotiation parameter of ports on the AT-8414/SC and AT-8414/ST line cards has a fixed value of '10Mbps full-duplex' and cannot be modified.
PAGE 73
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006 Family This section describes AT-View Plus Device Manager menus and operations specific to the AT9006SX/SC and AT-9006T switches.
PAGE 74
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006T Device Manager LEDs for AT-9006 Family LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - Ports on the expansion modules are numbered starting from 7.
PAGE 75
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Info Displays network-related information such as agent's and default gateway address. Manager Address Info Displays management station's IP address. Reset Reset the switch. Telnet Connect to the switch's telnet service. Bridge Menu From the Bridge menu, you can view and edit information such as forwarding database and spanning tree status. Forwarding Database Displays forwarding database table.
PAGE 76
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Log Displays RMON Event log. VLAN Menu From the VLAN menu, you can view the list of VLAN and member ports. Note - You cannot modify VLAN configuration on the AT-9006 Family using the VLAN menu. Name List Displays configured VLAN names. Port Info Displays VLAN to which the port belongs. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays port's utilization information.
PAGE 77
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9410GB This section describes AT-View Plus Device Manager menus and operations specific to the AT9410GB switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-9410GB Device Manager LEDs for AT-9410GB LED State Description PWR Green The switch is receiving power. DUPLEX Green The port is operating at full-duplex mode. Orange The port is operating at half-duplex mode.
PAGE 78
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - When a port on the AT-9410GB is set to 'auto sense' and is connected to a half-duplex port on another device, its corresponding Duplex LED on the device image turns green instead of orange. Note - A GBIC image is always visible on each of the GBIC slots of the device image even if there are no GBICs physically inserted. Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.
PAGE 79
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Bridge Info Displays basic bridge information such as the LAN ID, bridge address, number of ports and the bridge type. Forwarding Database Displays the Forwarding Database table.
PAGE 80
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.
PAGE 81
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Enable Enables the port. Disable Disables the port. QoS Displays QoS parameters and allows enabling of QoS status and setting priority queue. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source and destination. IGMP Snooping Displays the current state of IGMP Snooping and allows reconfiguration.
PAGE 82
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-FH800u This section describes AT-View Plus Device Manager menus and operations specific to the ATFH812u and AT-FH824u hubs. Topics: • • • • • • Main Window Agent Menu Hub Menu Module Menu RMON Menu Port Menu Main Window AT-FH800u Series Device Manager LEDs for AT-FH800u LED State Description PWR Green The hub is receiving power.
PAGE 83
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Network Info Displays network-related information such as the device's IP address, and the default gateway address.
PAGE 84
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Module Menu From the Module menu, you can view and edit MIB information about a selected hub in the stacked group. Status Displays information such as operation status and object identifier. Note - The current firmware version returns 'noSuchName' for the following parameters: • Module Description • Last Update Time and Date RMON Menu From the RMON menu, you can view and edit RMON MIB.
PAGE 85
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Status Displays whether the port is enabled or disabled, whether it is partitioned and other status information. Detail Status Displays information such as port name, LED status and polarity. Note - A link between a port on the hub and a port on another device can only be established if the port on the other device is configured to auto-negotiate. Security Info Displays source MAC addresses of frames received on the port.
PAGE 86
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR200E This section describes AT-View Plus Device Manager menus and operations specific to the ATAR240E, AT-AR250E, and AT-AR255E ADSL bridge/routers.
PAGE 87
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR250E AT-AR255E Device Manager LEDs for ADSL Bridge/Router LED State Description PWR Green The router is receiving power. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button. Note - The port speed displayed on the Ethernet port images is always '100' even if the Ethernet port is connected to a 10Mbps port on another device.
PAGE 88
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The four Ethernet ports on the AT-AR250E and AT-AR255E operate as a single port. As a result, even if connection is established on just one port, all four ports will turn green. Note - Expect the ADSL port to be green even if there is no physical connection established. Note - The current firmware version does not allow you to disable the Ethernet ports.
PAGE 89
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. Note - The current firmware version does not allow the user to configure the Destination Port Number parameter. Attempting to configure this parameter will result in the error messages: "The error occurred with 'Set' operation. Error: gen Error." or "The error occurred with 'Set' operation. Error: bad value.
PAGE 90
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database, discard/aging time information, and spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 91
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ATUR Performace Data by Interval Diplays collection of ATUR performance statistics in 15-minute intervals. Note - The ATUR Performance Data by Interval sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. ATUR Channel Performance Data Displays ATUR channel performance statistics like received blocks, transmitted blocks, and error counts.
PAGE 92
Allied Telesyn • • • • • • • • AT-VIEW PLUS DEVICE MANAGEMENT Max VPC Max VCC Max Active VPI Bits Max Active VCI Bits ILMI VPI ILMI VCI Neighbor IP Address Neighbor Name Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error." Interface DS3 PLCP Displays DS3 PLCP configuration and state parameters. Note - The Interface DS3 PLCP sub-menu option does not display the correct parameters.
PAGE 93
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Virtual Path Link (VPL) Displays configuration and state information for a bi-directional Virtual Path Link. Note - The Virtual Path Link (VPL) sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. Virtual Channel Link (VCL) Displays configuration and state information for a bi-directional Virtual Channel Link.
PAGE 94
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Virtual Channel (VC) Cross Connect sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. AAL5 Performance Statistics Displays performance statistics information associated with an AAL5 virtual channel connection. Note - AT-AR240E : The Port Number parameter is not relevant and should be ignored.
PAGE 95
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The LQR Info sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. LQR Configuration Displays Link Quality Report configuration information for a particular PPP link. Note - The LQR Configuration sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.
PAGE 96
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Media Status Diplays the types of MAC frames that can be sent or received across each of the system's interfaces. Bridge Media Configuration Displays configuration information used to negotiate the MAC types to be sent or received. Note - The current firmware version does not allow the Local Status parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.
PAGE 97
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-View Plus Device Manager allows the user to enter up to 63 characters for the Identity and Secret parameters. Entering more than 63 characters will result in the error message: "The error occurred with 'Set' operation. Error: bad value." Note - Security Secrets parameters return to their default values whenever the device is restarted. Note - The current firmware version does not allow the Direction parameter to be configured.
PAGE 98
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300 and AT-AR300L This section describes AT-View Plus Device Manager menus and operations specific to the ATAR300 and AT-AR300L routers.
PAGE 99
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300L Device Manager LEDs for AT-AR300 and AT-AR300L LED State Description PWR Green The router is receiving power. B1 Green Data or voice is being transmitted over the B1 channel of the ISDN interface. Gray B2 Green Gray No data or voice is being transmitted over the B1 channel or if the device is connected to a frame relay network. Data or voice is being transmitted over the B2 channel of the ISDN interface.
PAGE 100
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the router. Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router.
PAGE 101
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Info Displays information about errors related to the Frame Relay module. Call List Menu From the Call List menu, you can view ISDN call information. Detail Info Displays ISDN call information such as ISDN nubmer and call direction. Spanning Tree Info Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
PAGE 102
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR320 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR320 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR320 Device Manager LEDs for AT-AR320 LED State Description PWR Green The router is receiving power.
PAGE 103
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 104
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
PAGE 105
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR350 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR350 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR350 Device Manager LEDs for AT-AR350 LED State Description PWR Green The router is receiving power. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet.
PAGE 106
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router. Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions.
PAGE 107
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 108
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR370(S) and AT-AR370(U) routers.
PAGE 109
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370(U) Device Manager LEDs for AT-AR370(S) and AT-AR370(U) LED State Description PWR Green The router is receiving power. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system.
PAGE 110
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status.
PAGE 111
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Active Call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 112
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR410 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR410 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR410 with PIC installed Device Manager LEDs for AT-AR410 LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
PAGE 113
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 114
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Frame Relay Menu From the Frame Relay menu you can view and edit Frame Relay information. The Frame Relay submenus are greyed out if Frame Relay is not configured.
PAGE 115
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR440S and AT-AR441S This section describes AT-View Plus Device Manager menus and operations specific to the ATAR440S and AT-AR441S routers.
PAGE 116
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR441S Device Manager LEDs for the AT-AR440S and AT-AR441S LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex. Gray The port is either inactive or is operating at half-duplex. Green The interface is enabled and the link is up. Orange The interface is enabled and is handshaking. The interface is enabled and is training to negotiate the link.
PAGE 117
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT File List Displays a list of the files in the router's flash and NVS file systems. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled.
PAGE 118
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ATM Menu From the ATM menu you can view and edit ATM information. The ATM instance submenus are greyed out if no ATM instances are configured. The ATM channel submenus are greyed out if no ATM channels are configured. Instance Configuration Displays ATM Instance configuration information.
PAGE 119
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Physical Info Displays information about the ADSL physical layer parameters. Performance Statistics Displays ADSL event counters. Interval Statistics Displays ADSL interval counters. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Utilization Displays the port's utilization information.
PAGE 120
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR450S This section describes AT-View Plus Device Manager menus and operations specific to the ATAR450S router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR450S Device Manager LEDs for AT-AR450S LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex. Gray The port is either inactive or is operating at half-duplex.
PAGE 121
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router. WEB browser Opens your web browser and connects to the switch's HTTP server.
PAGE 122
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 123
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR720 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR720 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR720 with PICs installed Device Manager LEDs for AT-AR720 LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
PAGE 124
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 125
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 126
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port’s spanning tree parameters. This option is greyed out if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
PAGE 127
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725 This section describes AT-View Plus Device Manager menus and operations specific to ATAR725 and AT-AR725-DC routers.
PAGE 128
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725-DC Device Manager LEDs for AT-AR725 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled.
PAGE 129
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-AR725 AC only) File List Displays a list of the files in the router’s flash file system.
PAGE 130
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are unavailable if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry’s aging timer expired.
PAGE 131
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port’s spanning tree parameters. This option is unavailable if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
PAGE 132
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR740 and AT-AR740-DC routers.
PAGE 133
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740-DC Device Manager LEDs for AT-AR740 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled.
PAGE 134
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note – To turn RPS monitoring on or off on the router, from the AT-AR740 console enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on. Note – The current firmware version does not allow AT-View Plus Device Manager to support the RPS LED on the AT-AR740-DC model.
PAGE 135
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges are not configured.
PAGE 136
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port’s spanning tree parameters.
PAGE 137
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR745 and AT-AR745-DC routers.
PAGE 138
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745-DC Device Manager LEDs for AT-AR745 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled.
PAGE 139
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Before hotswapping in the NSM bay, make sure periodic device polling is enabled (File menu -> Properties). Note - To turn RPS monitoring on or off on the router, from the AT-AR745 console enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 140
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status.
PAGE 141
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 142
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8500 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8500 Series.
PAGE 143
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8550GB AT-8550SP PN 613-50665-00 Rev C Page 143 of 294
PAGE 144
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8500 Series LED State Description PWR Green The switch is receiving power. MASTER Orange Gray DUPLEX Green Orange The switch is the master switch of an enhanced stack. The switch is a slave switch or is not a member of an enhanced stack. The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 145
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT MAC Address Table Displays a list of static MAC addresses configured on the switch. Note - The MIB (atiStackSwitch.mib v2.10) supported by the current firmware version defines the Module ID and Port ID parameters as "read-write". As a result, AT-View Plus Device Manager displays these parameters as configurable objects. However, attempting to configure these parameters will show that the firmware does not accept any value.
PAGE 146
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version is unable to provide History Control Table information. As a result, the following error message appears: "Failed to get MIB data." Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
PAGE 147
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Valid MIB Set values for the Port Back Pressure parameter are 'disable' and 'enable'. Attempting to set Port Back Pressure to 'unknown' will cause the parameter to be set to 'enable'. Note - The Port CoS/QoS Priority parameter is not applicable to the AT-8500 series and should be ignored.
PAGE 148
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Mirroring Source Module, Mirroring Source Port and Mirroring Destination Module parameters are not applicable to the AT-8500 series and should be ignored. MAC Address Security Displays MAC Address Security parameters and allows you to set the security level for dynamic and static MAC addresses learned and assigned to a port.
PAGE 149
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version allows the Port Speed and Mode parameter of the AT-A47 expansion module port to be set to '10Mbps full-duplex' or '100Mbps fullduplex' even if the GBIC installed is not capable of 10/100 Mbps connectivity. Note - The Port Speed and Mode parameter of the AT-STACKM expansion module port should have a fixed value of 'auto sense'.
PAGE 150
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8724XL This section describes AT-View Plus Device Manager menus and operations specific to the AT8724XL and AT-8724XL-DC Advanced Layer 2 Switches.
PAGE 151
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8748XL Device Manager LEDs for AT-8700XL Series (AC Models) LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 152
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Uplink Modules for the operations and behavior of the uplink modules installed on these devices. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 153
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache), on the switch. Address Table Displays the list of IP interfaces and their IP addresses on the switch. Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received.
PAGE 154
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port.
PAGE 155
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9400 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT9400 Series.
PAGE 156
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9424T/SP Device Manager LEDs for AT-9400 Series LED State Description PWR Green The switch is receiving power. MASTER Orange Gray DUPLEX Green Orange The switch is the master switch of an enhanced stack. The switch is a slave switch or is not a member of an enhanced stack. The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 157
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Note - Configuring the System Contact, System Name and System Location parameters may sometimes result in the error message: "The error occurred with 'Set' operation. Error: gen Error." However, the values are still set successfully.
PAGE 158
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 159
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.
PAGE 160
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - When the priority level of a CoS Queue parameter is modified, what actually gets modified is the priority level of the next higher priority queue. In addition, the priority level is set to the next higher priority. Note - The current firmware version does not allow the CoS Queue parameters to be set to the following values: • • • • egress-queue-4 egress-queue-5 egress-queue-6 egress-queue-7 Enable Enables the port. Disable Disables the port.
PAGE 161
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Stacking Menu From the Stacking menu, you can access slave switches and other Master switches in the enhanced stack. Stacking Info Displays Enahanced Stacking parameters, allows you to set the switch's enhanced stacking status and select a switch to manage in the enhanced stack.
PAGE 162
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8624T/2M This section describes AT-View Plus Device Manager menus and operations specific to the AT8624T/2M Layer 3 Switch.
PAGE 163
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8624T/2M LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 164
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache), on the switch. Address Table Displays the list of IP interfaces and their IP addresses on the switch. Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received.
PAGE 165
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics. Spanning Tree Info Displays the port's spanning tree parameters. MAU Info Displays interface-related MAU information for the port. MAU Negotiation Info Displays the MAU's auto-negotiation settings and its status. Enable Enables the port.
PAGE 166
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8800 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8800 Series of Intelligent Workgroup Switches.
PAGE 167
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8848 Device Manager LEDs for AT-8800 Series LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 168
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Firmware Info Displays a list of software releases installed on the switch. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. File List Displays a list of the files in the switch's file system. Config File Name Displays the file name of the start-up configuration file.
PAGE 169
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT IP Statistics Displays statistics about IP, such as the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, such as the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 170
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Enable Enables the port. Disable Disables the port.
PAGE 171
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/MT and 16F/SC This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 16F/MT and Rapier 16F/SC Layer 3 Fast Ethernet Switches.
PAGE 172
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/SC Device Manager LEDs for Rapier 16F/MT and Rapier 16F/SC LED State Description PWR Green The switch is receiving power from the main power supply. Red The main power supply has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 173
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on. Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet.
PAGE 174
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 175
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
PAGE 176
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24 and 24i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 24 and Rapier 24i Layer 3 Fast Ethernet Switches.
PAGE 177
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24i Device Manager LEDs for Rapier 24 and 24i LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 178
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on. Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet.
PAGE 179
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 180
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
PAGE 181
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48 and 48i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 48 and Rapier 48i Layer 3 Switches.
PAGE 182
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48i Device Manager LEDs for Rapier 48 and 48i LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 183
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. File List Displays a list of the files in the switch's file system.
PAGE 184
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded for reasons such as lack of memory or the entry's aging timer. Spanning Tree Info Displays spanning tree parameters such as priority and cost.
PAGE 185
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6 This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6 Layer 3 Gigabit Ethernet Switch.
PAGE 186
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for Rapier G6 LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 187
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Connects to the switch's Telnet server. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch.
PAGE 188
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics. Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port.
PAGE 189
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-LX/SC, G6F-SX/SC, G6FSX/MT-RJ This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6F-LX/SC, Rapier G6F-SX/SC and Rapier G6F-SX/MT-RJ Layer 3 Gigabit Ethernet Switches.
PAGE 190
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-SX/SC Rapier G6F-SX/MT-RJ PN 613-50665-00 Rev C Page 190 of 294
PAGE 191
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for Rapier G6F LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 192
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Connects to the switch's Telnet server WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch.
PAGE 193
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
PAGE 194
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8948 This section describes AT-View Plus Device Manager menus and operations specific to the AT8948 Enhanced Layer 3+ Switch.
PAGE 195
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8948 LED State PWR 1 and Green PWR 2 Description There is a power supply unit (PSU) in the PSU bay, and it is supplying power to the switch. There is a functioning Fan Only Module (FOM) in the PSU bay.
PAGE 196
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Reset Cold Reset Cold resets the hardware and executes the default configuration file.
PAGE 197
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
PAGE 198
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade This section describes AT-View Plus Device Manager menus and operations specific to the SwitchBlade Series, including the AT-SB4211 Switch Controller, power supply units and fan tray installed.
PAGE 199
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window SwitchBlade 4004 with SB4211 Switch Controller, SB4215 Bandwidth Expander, and Line Cards installed PN 613-50665-00 Rev C Page 199 of 294
PAGE 200
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4008 with SB4211 Switch Controller and Line Cards installed PN 613-50665-00 Rev C Page 200 of 294
PAGE 201
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-SB4211 Switch Controller LED State Description PWR Green The PSU is receiving power from its supply circuit. MASTER Orange The card is the master switch controller. Gray The card is a slave switch controller. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 202
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis board, and switch controller and line card boards installed in the device. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
PAGE 203
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. For each Port menu option, select first the slot in the SwitchBlade chassis, then the ports in the line card for which you require information.
PAGE 204
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade Line Cards This section describes the SwitchBlade Line Cards in AT-View Plus Device Manager. If the following Line Cards are installed in a SwitchBlade chassis, they are displayed in the main window. The operations available for the SwitchBlade include any of these line cards.
PAGE 205
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-SB4411 8-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-SB4412 24-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.
PAGE 206
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-SB4452 8-Port (MT-RJ) 1000BASE-SX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4461 8-Port (SC) 1000BASE-LX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4462 8-Port (MT-RJ) 1000BASE-LX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex.
PAGE 207
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9700 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT9700 Series of Advanced Layer 3 Gigabit Switches.
PAGE 208
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-9724TS The AT-9724TS supports up to 12 stacked AT-9724TS switches.
PAGE 209
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9748TS/XP The AT-9748TS/XP supports up to 8 AT-9748TS/XP stacked switches or any of the following mixed stack combinations of AT-9748TS/XP and AT-9724TS switches.
PAGE 210
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9748TS/XP AT-9724TS 7 <=2 6 <=4 5 <=6 4 <=8 3 <=9 2 <=10 1 <=11 Device Manager LEDs for AT-9700 Series LED State Description PWR Green The switch is receiving power from the main power supply. RPS Green The switch is receiving power from the redundant power supply. Gray RPS is not installed or not functioning. STACK ID Green The stacked unit is either a slave switch or the switch is not in a stacked mode.
PAGE 211
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-View Plus Device Manager detects that the established link speed is less than 1Gbps, only the RJ-45 port images will turn green. Note - When multiple units of the AT-9700 series are stacked together, port numbering is continuous based on the Box ID.
PAGE 212
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Info General Info Displays common management information. General Config Displays basic control of the system. Note - The current firmware version does not allow the RS-232C Mode parameter to be configured. Note - The current firmware version returns 'noSuchName' for the Asymmetric VLAN Status parameter. MIB List Displays the list of MIB capability entries supported by the system.
PAGE 213
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Alarm Config Displays trap configurations status. Date and Time System Date and Time Displays the current date and time configurations of the system. Summer Date and Time Displays the summer date and time configurations of the system. Note - The current firmware version does not allow the following parameters to be configured: o o o o Repeating Start Repeating End Annual Start Annual End SNTP Displays the SNTP configuration of the system.
PAGE 214
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT IP Interface Info Displays information about IP interfaces. Note - The current firmware version does not allow the following parameters to be configured: o o o o o Interface Name IP Subnet Mask VLAN Name Operation Mode Secondary IP Note - Valid MIB Set values for the Row Status parameter are 'active' and 'not in service'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation.
PAGE 215
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT TCP Statistics Displays the TCP Statistics. CIDR Route Number Displays the number of valid CIDR entries. Route Table Displays the CIDR routing tables. Note - The current firmware version does not allow the following parameters to be configured: o o o o Next Hop AS Number Destination Metric 2 Destination Metric 3 Destination Metric 4 ICMP Statistics Displays the ICMP Statistics. Route Preferences Displays configurations of routing preferences.
PAGE 216
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Valid MIB Set values for the Row Status parameter are 'active' and 'not in service'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value". Active Peer Info Displays information about active peer relationships. Note - The Active Peer Info sub-menu option does not display the correct parameters.
PAGE 217
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Address Range Info sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. Host Info Displays the list of hosts, and their metrics, that the device will advertise as host routes. Interface Info Displays the interfaces from the viewpoint of OSPF.
PAGE 218
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The External Link State Ads sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. Area Aggregate Info Displays the range of IP addresses specified by an IP address/IP network mask pair . DVMRP Basic Info Displays basic information about Distance Vector Multicast Routing Protocol. Interface Info Displays the list of device's multicast capable interfaces.
PAGE 219
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Next Hop Table sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. PIM Join/Prune Interval Displays the default interval at which periodic PIM-SM Join/Prune messages are to be sent. Interface Info Displays the list of device's Protocol Independent Multicast interfaces. Neighbor Info Displays the list of device's PIM neighbors.
PAGE 220
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Component Displays the list of objects specific to a PIM. Note - The Component sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. IPM Basic Info Displays basic information about IP Multicast Routing Protocol. Interface Info Displays the list of multicast routing information specific to interfaces.
PAGE 221
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Next Hop Table Displays the table containing information on the next hops on outgoing interfaces for routing IP multicast datagrams. Note - The Next Hop Table sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. BOOTP Relay Basic Info Displays basic information about BOOTP relay function.
PAGE 222
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the following parameters to be configured: o o o o o o o o o VLAN Range List 1 - 64 VLAN Range List 65 - 128 VLAN Range List 129 - 192 VLAN Range List 193 - 256 VLAN Range List 257 - 320 VLAN Range List 321 - 384 VLAN Range List 385 - 448 VLAN Range List 449 - 512 Row Status Statistics Displays statistics about frames received/transmitted on the switch port.
PAGE 223
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Join Time, Leave Time and Leave All Time to be configured. IGMP Menu From the IGMP menu, you can view and edit IGMP information such as IGMP queries and reports sent between devices, VLAN's IGMP functions and interfaces on which IGMP is enabled. IGMP Config Displays configurations of the Internet Group Management Protocol function.
PAGE 224
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT VRRP Menu From the VRRP menu, you can view and edit VRRP-related information such as the current VRRP version, VRRP status, VRRP statistics and IP addresses associated with VRRP. Basic Info Displays basic information such as the particular version of the Virtual Routing Redundancy Protocol supported by the device and the whether the VRRP-enabled router will generate SNMP traps.
PAGE 225
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Authenticator PAE Statistics Displays statistics objects for the Authenticator PAE associated with each Port. Note - The current firmware version returns 'noSuchName' for the Port Number parameter. Authenticator PAE Diagnostics Displays diagnostics objects for the Authenticator PAE associated with each Port. Note - The current firmware version returns 'noSuchName' for the Port Number parameter.
PAGE 226
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Authenticator PAE Diagnostics sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. Authenticator PAE Session Statistics Displays session statistics objects for the Authenticator PAE associated with each MAC address. Note - The Authenticator PAE Session Statistics sub-menu option does not display the correct parameters.
PAGE 227
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Secure Socket Layer SSL Config Displays the status of SSL support and cipher suites, and the cache timeout value for SSL module to refresh the session resume data kept in database. Note - The current firmware version does not allow the Cipher Suites parameter to be configured. Certificate File Displays the parameters used on downloading certificate or key file.
PAGE 228
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the following parameters to be configured: o o o Source MAC Address Mask Destination MAC Address Mask Ethernet Type IP Info Displays ACL mask of IP information.
PAGE 229
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Packet Content Rule Displays ACL rule of user-defined information. Note - The current firmware version does not allow the following parameters to be configured: o o o o o Offset 0 to 15 Offset 16 to 31 Offset 32 to 47 Offset 48 to 63 Offset 64 to 79 RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table.
PAGE 230
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about selected ports. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Note - The current firmware version returns '??? (117)' for the Port Type parameter. Error Statistics Displays error statistics for the port.
PAGE 231
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Deletion Displays configuration parameters to allow port security deletion. Note - The current firmware version does not allow the MAC Address and Port Security Deletion Activity parameters to be configured. Traffic Management Config Displays traffic control configuration parameters for every port present in the switch. Segmentation Displays the information that specifies the port with its traffic forward list.
PAGE 232
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Trunking Basic Info Displays basic information about port trunking. Trunk Config Displays port trunking parameteres and allows configuration of the master port, member ports, trunk type and trunk status. Note - The current firmware version does not allow the Member Ports and Trunk Type parameters to be configured. Aggregator Info Displays information about every Aggregator that is associated with this system.
PAGE 233
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LACP Debug Displays ink Aggregation debug information about every port that is associated with this device. Note - The current firmware version returns 'noSuchName' for all parameters under this sub-menu option.
PAGE 234
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9800 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT9800 Series of Multi-Layer Gigabit Switches.
PAGE 235
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9816GB Device Manager LEDs for AT-9800 Series LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 236
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. Firmware Info Displays a list of software releases installed on the switch.
PAGE 237
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the switch. Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received.
PAGE 238
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT MAU Info Displays interface-related MAU information for the port. MAU Negotiation Info Displays the MAU's auto-negotiation settings and its status. Enable Enables the port. Disable Disables the port.
PAGE 239
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9924T, AT-9924SP, AT-9924T/4SP This section describes AT-View Plus Device Manager menus and operations specific to the AT9924T, AT-9924SP and AT-9924T/4SP Advanced Layer 3+ Gigabit Switches.
PAGE 240
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9924SP AT-9924T/4SP PN 613-50665-00 Rev C Page 240 of 294
PAGE 241
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-9924T, AT-9924SP, AT-9924T/4SP LED State PWR 1 and Green PWR 2 Description There is a power supply unit (PSU) in the PSU bay, and it is supplying power to the switch. There is a functioning Fan Only Module (FOM) in the PSU bay.
PAGE 242
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Chassis Temperature and Fan Info Displays the actual temperature of the switch, the temperature status, and the fan status. Reset Reset Cold resets the hardware and executes the default configuration file. Reset Warm performs a warm start of the software modules and executes the default configuration file. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
PAGE 243
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
PAGE 244
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF06 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF06 family of media converters.
PAGE 245
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF06 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 246
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter.
PAGE 247
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF12 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF12 family of media converters.
PAGE 248
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF12 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 249
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12.
PAGE 250
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF106 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF106 family of media converters.
PAGE 251
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF106 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 252
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter.
PAGE 253
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF112 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF112 family of media converters.
PAGE 254
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF112 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 255
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12.
PAGE 256
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MPB3000 This section describes AT-View Plus Device Manager menus and operations specific to the ATMPB3000 chassis.
PAGE 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-MPB3000 Note - The current firmware version does not allow AT-View Plus Device Manager to support stacked AT-MPB3000 devices.
PAGE 258
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MPB3000 LED State Description PWR1 Green Power supply 1 is installed and power is on. Gray Power supply 1 is not installed or it is installed but not powered on. Green Power supply 2 is installed and power is on. Gray Power supply 2 is not installed or it is installed but not powered on. Green The optional redundant power supply is installed and power is on.
PAGE 259
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MPB3000 Modules This section describes the modules supported by AT-View Plus Device Manager. If modules are installed on the AT-MPB3000 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.
PAGE 260
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The MCM100-02 module image applies to the following variants: • • • • AT-MCM100-02SC AT-MCM100-02SMR AT-MCM100-02SMRF15 AT-MCM100-02ST AT-MCM110 Modules MCM110-01 MCM110-02 LED State Description RAD Green The FX port is connected to a remote access device.
PAGE 261
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCM1000S Modules MCM1000S LED State Description RAD Green The LX port is connected to a remote access device. Note - The TP Link Status parameter reflects the status of the SX port while the F/O Link Status parameter reflects the status of the LX port. Note - The remote access device connected to the LX port may at times be inaccessible when link is established on the SX port.
PAGE 262
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCM1000T Modules MCM1000T LED State Description RAD Green The LX port is connected to a remote access device.
PAGE 263
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade This section describes AT-View Plus Device Manager menus and operations specific to the ATPBC18 chassis.
PAGE 264
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-PBC18 LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The optional redundant power supply is installed and power is on. Gray The optional redundant power supply is not installed or it is installed but not powered on.
PAGE 265
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Info Displays power supply voltage information. Battery Voltage Displays the battery voltage information. Omega Displays Omega management interface information, including time-out and port status (RS-232 and 10Base-T). Telnet Starts a Telnet connection to the chassis. Status Menu From the Status Menu, you can view and edit information about PowerBlade Modules installed on the chassis. Options to view all/per module information are displayed.
PAGE 266
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade Modules This section describes the modules supported by AT-View Plus Device Manager. If modules are installed on the PowerBlade chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.
PAGE 267
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB100 Series Media Converter Modules PB101 PB102 PB103/1 PB103/2 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - The Port A Mode parameter for these modules has a fixed value of 'full' and cannot be modified.
PAGE 268
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB200 Series Switch Modules PB201 PB202 PB202/1 PB202/3 PB202/4 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The 10/100Base-TX port is auto-negotiating.
PAGE 269
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB300 Series Media Converter Modules PB301 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - Port A is displayed as an SC connector instead of a VF-45 connector. Note - The Port A Mode parameter for this module has a fixed value of 'full' and cannot be modified.
PAGE 270
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB1000 Series Media Converter Modules PB1001/1 PB1001/3 LED State Description LT Green Link Test is enabled SML Green Smart Missing Link is enabled ML Green Missing Link is enabled PB1005G Note - Smart Missing Link is only supported on the AT-PB1005G module. However, the current firmware version allows the Link Test parameter of the AT-PB1001/1 and AT-PB1001/3 modules to be set to 'smart-missing-link'.
PAGE 271
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG213 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATRG213FX and AT-RG213TX Residential VoIP Gateways. Topics: • • • • Main Window Agent Menu RTC Menu Port Menu Main Window AT-RG213 Device Manager LEDs for AT-RG213FX and AT-RG213TX LED State Description PWR Green The residential gateway is receiving power. Note - The AT-RG213FX and the AT-RG213TX share the same device image.
PAGE 272
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Note - The current firmware version does not allow the following parameters to be configured: • • • System Name System Location System Contact Attempting to configure these parameters will result in the error message: "The error occured with 'Set' operation. Error: time out occured.
PAGE 273
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Link State Port Type Port Speed Port Duplex Mode Port Autonegotiation State Voice Displays information for each voice port. Information displayed will vary depending on the protocol used : H.323, Media Gateway Control (MGCP), or Session Initiation (SIP). Note - H.323 : The Port Capability parameter does not display all capabilities used during call setup.
PAGE 274
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - SIP : The current firmware version returns the value of the Location Server IP Address parameter on the Port Proxy Server IP Address parameter and the value of the Proxy Server IP Address parameter on the Port Location Server IP Address parameter.
PAGE 275
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG600 Series This section describes AT-View Plus Device Manager menus and operations specific to the ATRG600 Ethernet and ADSL Residential Gateways.
PAGE 276
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG613TX AT-RG634A PN 613-50665-00 Rev C Page 276 of 294
PAGE 277
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG656BD Device Manager LEDs for AT-RG600 Series LED State Description PWR Green The residential gateway is receiving power. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - The current firmware version does not allow AT-View Plus Device Manager to determine the negotiated mode for active LAN or WAN ports that are configured to auto-negotiate. As a result, the Duplex LED will turn gray.
PAGE 278
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - The current firmware version does not allow the user to enter multiple-word values for the System Name parameter. Attempting to do so will result in the error message: "The error occurred with 'Set' operation.
PAGE 279
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT If GSPAN is loaded on the device, the same behavior may occur when the Comment or Password parameters are set to a string that is more than 65 characters long and more than 84 characters, respectively, Note - AT-RG656BD: Valid MIB Set values for the Comment parameter are in the range [0-89] inclusive.
PAGE 280
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG656BD: The current firmware version does not allow the Learning Status parameter to be set to 'disable'. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: time out occurred." Note - AT-RG656BD : Changing the value of the Aging Time Mode parameter causes the Aging Time Value parameter to be set to 0.
PAGE 281
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Group Info Displays a list of all group multicast address. Server Info Displays a list of all multicast servers. Note - The Server Info sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. VoIP Menu From the VoIP menu, you can view and edit information related to telephony services available on the residential gateway.
PAGE 282
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG634A: Valid MIB Set values for the Interface parameter are in the range [1-75] inclusive. But the current firmware version allows the parameter to be set to more than 75 characters. Note - AT-RG634A: Valid MIB Set values for the NAT IP Address parameter are in the range [0-255] inclusive. Attempting to set this parameter to a value outside the valid range will result in the error message: "No access error.
PAGE 283
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG613xx : Changing the value of the Port Speed and Mode parameter will result in the error message: "The error occurred with 'Set' operation. Error: time out occurred." However, the new value is still set. Note - AT-RG634A: The current firmware version returns 'No such instance' for the Speed parameter when the Standard sub-menu option is selected. As a result, no speed is displayed on the RJ-45 LAN port images.
PAGE 284
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The port number assignment displayed in the Additional Info and Standard Info MIB Variable Window are inconsistent. Voice Displays information for each voice port. Note - AT-RG634A: The value displayed for the Port parameter is '???(0)'. Note - AT-RG634A: Device Manager takes a while in retrieving information from the device. As a result, the value 'no such instance' may be displayed by default.
PAGE 285
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Interface Cards This section describes the following Port Interface Cards supported in AT-View Plus Device Manager : • • • • • • • AT-AR020 AT-AR021 AT-AR022 AT-AR023 AT-AR024 AT-AR026 AT-AR027 If one of these PICs is installed in a PIC bay of a Router (AT-AR400 series or AT-AR700 series), or in a Network Service Module (NSM) of a Router or Layer 3 Switch (Rapier series), it is displayed in the PIC bay of the device in the main window.
PAGE 286
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR021(S) and AT-AR021(U) LED State B1 and B2 Green Gray Description For permanent circuits, HDLC packets are being exchanged between the switch or router and another end system device (normally another switch or router) over any of the B channel. For on-demand ISDN, there is a call up over the respective Bchannel. No packet/data transmission over B-channel. AT-AR022 Note - There are no LEDs on this PIC.
PAGE 287
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR027 Note - There are no LEDs on this PIC.
PAGE 288
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Service Modules This section describes the following Network Service Modules (NSMs) supported in AT-View Plus Device Manager. AT-AR040 4-PIC slot NSM Note - Up to four Port Interface Cards can be installed in the AT-AR040 NSM. Note - There are no LEDs on this NSM.
PAGE 289
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR041 and AT-AR042 LED State Data LEDs Orange Gray Description For permanent circuits, HDLC packets are being exchanged between the switch or router and another TE end system device (normally another switch or router) over the respective Bchannel. For on-demand ISDN, there is a call up over the respective B-channel. No packet/data transmission over B-channel.
PAGE 290
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Uplink Modules This section describes the Uplink Modules that can be installed in Layer 2 Switches, Advanced Layer 2 Switches, and Layer 3 Switches. Topics : • • Layer 2 Switches Uplink Modules Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules Layer 2 Switches Uplink Modules If the uplink modules are installed in one of the Layer 2 switches, they are displayed in the uplink bays of the device in the main window.
PAGE 291
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-A16 Device Manager LEDs for AT-A16 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A17 Device Manager LEDs for AT-A17 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A18 Device Manager LEDs for AT-A18 LED State Description DUPLEX Green The port is operating at full-duplex.
PAGE 292
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-A19 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A16/AT-A17/AT-A19 Device Manager LEDs for AT-A16/AT-A17/AT-A19 LED State Description DUPLEX Green The port is operating at full- duplex. Orange The port is operating at half-duplex. AT-A45/AT-A47/AT-STACKM Note - There are no LEDs on this module.
PAGE 293
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-A46 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules If the uplink modules are installed in one of the Rapier series or AT-8700XL series switches, they are displayed in the uplink bays of the device in the main window.
PAGE 294
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-A40/MT and AT-A40/SC LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A41 Device Manager LEDs for AT-A41/MT and AT-A41/SC LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.