AT-VIEW PLUS 3.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Copyright (c) 2003-2004 Allied Telesis K. K. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, K. K. Microsoft is a registered trademark of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT TABLE OF CONTENTS Basic Operations ................................................................................................................ 11 Common operations on the main window....................................................................... 12 Menu for stacked devices ............................................................................................... 13 Port selection dialog box.....................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window .................................................................................................................. 52 Agent Menu .................................................................................................................... 53 Bridge Menu ................................................................................................................... 54 RMON Menu...............................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window .................................................................................................................. 90 Agent Menu .................................................................................................................... 92 Routing Menu ................................................................................................................. 92 Bridge Menu .............................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR450S ......................................................................................................................................... 121 Main Window ................................................................................................................ 121 Agent Menu .................................................................................................................. 122 Routing Menu ........................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8748XL ....................................................................................................................... 147 Main Window ................................................................................................................ 147 Agent Menu .................................................................................................................. 148 Routing Menu ..........................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-LX/SC, G6F-SX/SC, G6F-SX/MT-RJ............................................................ 177 Main Window ................................................................................................................ 177 Agent Menu .................................................................................................................. 179 Routing Menu ......................................................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window ................................................................................................................ 213 Agent Menu .................................................................................................................. 214 Status Menu ................................................................................................................. 215 AT-MCF112 Family ..........................................................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Service Modules................................................................................................. 251 Uplink Modules................................................................................................................. 253 Layer 2 Switches Uplink Modules ................................................................................. 253 Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules ...........................
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT This document describes the operations and menus specific to particular Allied Telesyn models of managed devices. For module-independent information, refer to the AT-View Plus Device Manager User's Guide. Basic Operations AT-View Plus Device Manager's main window shows the main panel of the target device. It has both common and device-specific menus on its menu bar.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Common operations on the main window Right clicking on a port Port Right clicking on a port opens a pull-down menu specific to the device. Selecting a menu item opens another window and lets you view and edit MIB information related to the port. You can also access the same menu from the menu bar. RS-232 Terminal Port Right clicking on an RS-232 port opens a pull-down menu and lets you choose how to log into the agent.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Menu for stacked devices If the target is a stacked device, some menus have extra subitems to specify a single device in the stack.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port selection dialog box When you select a menu item acting on ports, a dialog box opens to let you select ports. Check the target ports and click OK. Note - If you select multiple ports, it may take some time for data to be displayed. Select Port dialog box Port status colors Port status is shown by its color. Port speed is also displayed in the port image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED status In AT-View Plus Device Manager, LEDs do not blink. The meanings of LEDs differ between devices. Utilization Utilization is calculated by the following formula.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8000 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8000 Series.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8016F/MT AT-8016F/SC PN 613-50665 Rev A Page 17 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8016F/ST AT-8024 PN 613-50665 Rev A Page 18 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8024GB AT-8024M PN 613-50665 Rev A Page 19 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8026FC AT-8026T PN 613-50665 Rev A Page 20 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8088/MT AT-8088/SC PN 613-50665 Rev A Page 21 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8000 Series LED State Description PWR Green The switch is receiving power. MASTER Orange Gray DUPLEX Green Orange The switch is the master switch of an enhanced stack. The switch is a slave switch or is not a member of an enhanced stack. The port is operating in full-duplex mode. The port is operating in half-duplex mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - Attempting to enter more than 39 characters for the System Contact, System Name, and System Location parameters may result in a timeout error.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Port Name parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName". Spanning Tree Info Displays the port's spanning tree parameters. Note - Setting a port's Port parameter to 'disabled' does not automatically set the Port State parameter under Detail Info to 'disabled'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Stacking Menu From the Stacking menu, you can perform enhanced stacking from any AT-8000 Series master switch. Stacking Info Displays information about the switch's mode. This is also the menu where you can perform enhanced stacking. Expansion Module Notes • AT-View Plus Device Manager cannot distinguish between the AT-A45/xx, AT-A47, and AT-STACKM expansion modules. All are displayed with the same GIF image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT • By default, the Port Speed and Mode parameter of the AT-A47 expansion module port is set to 'auto sense'. From this mode, the Port Speed and Mode can only be changed to '1Gbps fullduplex'. However, once set to '1Gbps full-duplex', it can no longer be set to 'auto sense'. • The Port Speed and Mode parameter of the AT-STACKM expansion module cannot be modified. It is fixed at '1Gbps full-duplex'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124 This section describes AT-View Plus Device Manager menus and operations specific to the AT8124 switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8124 LED State Description PWR Green The switch is receiving power. DUPLEX Green Gray The port is operating in full-duplex mode. The port is operating in half-duplex mode. Agent Menu From the Agent menu, you can view and edit the system information for the device or log into the CLI using telnet. System Info Displays basic system information, including system name, location, contact and description.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Detail Info Displays port traffic statistics such as the number of frames received/transmitted on the port. Error Statistics Displays error information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124XL (V2) This section describes AT-View Plus Device Manager menus and operations specific to the AT8124XL (V2) switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-8124XL (V2) Device Manager LEDs for AT-8124XL (V2) LED State Description PWR Green The switch is receiving power. DUPLEX Green Orange PN 613-50665 Rev A The port is operating in full-duplex mode. The port is operating in half-duplex mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the System Contact, System Name, and System Location parameters but truncates them to 64 characters. NULL values are not accepted.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch's ports. RMON Menu From the RMON menu you can view and edit the RMON MIB.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Detail Info Displays detailed port information such as duplex mode. Note - Enabling/Disabling the Port STP Configuration parameter for one port enables/disables STP for all ports. Note - Attempting to modify the Port Speed and Mode parameter from 'auto sense' to '1Gbps half-duplex' or '1Gbps full-duplex' will result in the following: • • An error message: "The error occurred with 'Set' operation.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination. IGMP Snooping Displays the current state of IGMP Snooping and allows reconfiguration.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8200XL Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8216FXL/SC and AT-8224XL switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8224XL Device Manager LEDs for AT-8200XL Series LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating at full-duplex mode. The port is operating at half-duplex mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version allows the user to enter up to 64 characters for the System Contact and the System Location parameters and up to 20 characters for the System Name parameter. Note - The current firmware version appends a period '.' and the value of the Default Domain Name parameter to the value of the System Name parameter. Firmware Info Displays the firmware version of the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Diagnostics Displays the operating status of the switch's components such as power supply and system fans. Note - The current firmware version returns 'non-supported' for the following parameters: • • • • • • Fan Speed 3 3.3V Power 2.5Va Power 2.5Vb Power 2V Power CPU Temperature Reset Resets the switch. Console Settings Displays the current settings of the console. Telnet Starts a Telnet connection to the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. RMON Menu From the RMON menu you can view and edit the RMON MIB.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics. Detail Info Displays detailed port information such as duplex mode. Note - The Port Flow Control parameter has a fixed value of 'not supported' and cannot be modified. Note - When the Port Speed and Mode parameter of an AT-8224XL fixed port is set to 'auto sense' and the port is connected to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Expansion Module Notes • • • • • • • • When the Port Speed and Mode parameter of an AT-A14 expansion module port is set to 'auto sense' and the port is connected to a 100Mbps full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green. The current firmware version does not allow the Port Speed and Mode parameter of the ATA14 expansion module port to be set to any value other than 'auto-sense'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324 This section describes AT-View Plus Device Manager menus and operations specific to the AT8324 switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Supports up to 8 stacked AT-8324 switches. Device Manager LEDs for AT-8324 LED State Description PWR Green The switch is receiving power. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - The current firmware version does not allow AT-View Plus Device Manager to support the RPS and the Master LEDs.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because of lack memory or the entry's aging timer has expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version is unable to retrieve the correct information for the History Control Table. As a result, the following error message appears: "Failed to get MIB data." Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version accepts from 0 up to 19 characters for the Port Name parameter. Note - The Port State parameter returns 'unknown' for active ports. Note - When a port is configured to auto-negotiate, the current firmware version does not always update its Port Duplex Status parameter with the correct negotiated mode. As a result, the port's Duplex LED may show up as green when it should really be orange and vice-versa.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Stacking Menu From the Stacking menu, you can view basic switch information as well as stacking information. Stacking Info Displays information such as Product Type, Port Count and Uplink Types for all switches in the stack.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324SX This section describes AT-View Plus Device Manager menus and operations specific to the AT8324SX switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8324SX Supports up to 4 stacked switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8324SX LED State Description PWR Green The switch is receiving power. RPS Green Redundant power is ON. Gray Redundant power is OFF. DUPLEX Gray STACK ID The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode. Green The switch's position in the switch stack. Note - When multiple units of AT-8324SX are stacked together, port numbering is continuous.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Displays the reset table that allows you to configure reset parameters before restarting the management agent. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information, such as the forwarding database and spanning tree status. Forwarding Database Displays the Forwarding Database table.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Table Displays the RMON event table. Event Log Displays the RMON event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Note - The current firmware version does not allow Port Menu to support the Class of Service. Utilization Displays the port's utilization information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value". Note - The Module ID and Port Number parameters return 'noSuchName'. Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8300GB Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8300GB Series.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8326GB PN 613-50665 Rev A Page 58 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT The AT-8326GB supports up to 6 AT-8326GB stacked switches or any of the following mixed stack combinations of AT-8326GB and AT-8350GB switches: • • • • Two AT-8326GB switches and one AT-8350GB switch Two AT-8326GB switches and two AT-8350GB switches Three AT-8326GB switches and one AT-8350GB switch Four AT-8326GB switches and one AT-8350GB switch Note - When 3 or more AT-8326GB devices are stacked together, expect the twisted pair port image of Port 26 on th
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow AT-View Plus Device Manager to support expansion modules that may be installed on the AT-8350GB. Device Manager LEDs for AT-8300GB Series LED State Description PWR Green The switch is receiving power. STACK ID Green The switch's position in the switch stack. DUPLEX Green The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Info Displays network-related information such as the device IP address and the default gateway address. Note - The current firmware version does not save changes made to the DNS Server and the Default Domain Name parameters. DHCP Info Displays DHCP information including the DHCP System Group and DHCP Timer Group. Manager Address Info Displays the IP address of the management station. Reset Resets the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Port Bridge ID parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value". Note - When a port's Port Speed and Mode parameter is set to 'auto sense', the current firmware version does not update its Port Duplex Status parameter with the negotiated mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Security Action parameter returns '???(0)' when the Security Configuration parameter is set to 'disabled'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 This section describes AT-View Plus Device Manager menus and operations specific to the AT8400 switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8400 Device Manager LEDs for AT-8401 Management Module LED State Description FAN A Green FAN TRAY A is installed and is operating correctly. Gray FAN TRAY A is not installed. Green FAN TRAY B is installed and is operating correctly. Gray FAN TRAY B is not installed. FAN B MASTER Green Gray PN 613-50665 Rev A The switch is the master of an enhanced stack.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT is not a member of an enhanced stack. RPS Green The switch is receiving power from the redundant power supply (PWR B). Gray The switch is receiving power from the main power supply (PWR A). PWR Green Gray (Only if RPS is installed) The switch is receiving power from the main power supply (PWR A). The main power supply is not functioning. Note - Please refer to AT-8400 Line Cards for the operations and behavior of the line cards installed on the chassis.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note -The current firmware version does not allow the Power A Status and Power B Status parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error.". Line Card Info Displays information for each line card including line card type and line card temperature. MAC Address Table Displays a list of static MAC address configured on the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - When setting the Spanning Tree Status parameter to 'enabled', connection to the AT8400 is temporarily lost. As a result, the following error message appears: "The error occurred with 'Set' operation. Error: time out occurred.". Note - Setting the value of the Spanning Tree Version parameter to 'stp' will result in a permanent loss of connection. To re-establish connection, restart the device.
Allied Telesyn • • • • AT-VIEW PLUS DEVICE MANAGEMENT Utilization Interface Info -> Standard Error Statistics -> Standard Spanning Tree Info Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Valid MIB Set values for the Port Mirroring Configuration Entry Status parameter are 'active', 'not in service' and 'destroy'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.". Stacking Menu From the Stacking menu, you can view basic switch information as well as stacking information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 Line Cards This section describes the AT-8400 Line Cards supported by AT-View Plus Device Manager. If line cards are installed on the AT-8400 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image. • • • • AT-8411 AT-8412 AT-8413 AT-8414 AT-8411 AT-8411 LED State Description DUPLEX Green The port is operating in full-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8412 AT-8412/MT AT-8412/SC LED State Description DUPLEX Green The port is operating in full-duplex. Note - The current firmware version does not allow the Port Flow Control parameter of ports on the AT-8412/MT and AT-8412/SC line cards to be set to 'auto'. Attempting to set this parameter to 'auto' will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Description DUPLEX Green The port is operating in full-duplex. Orange The port is operating in half-duplex. Note - A GBIC image is always visible on the GBIC slot of the AT-8413GB/T line card image even if there is no GBIC physically present in the slot.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Port Negotiation parameter of ports on the AT-8414/SC and AT-8414/ST line cards has a fixed value of '10Mbps full-duplex' and cannot be modified.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006 Family This section describes AT-View Plus Device Manager menus and operations specific to the AT9006SX/SC and AT-9006T switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006T Device Manager LEDs for AT-9006 Family LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - Ports on the expansion modules are numbered starting from 7.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Firmware Info Displays firmware version. Network Info Displays network-related information such as agent's and default gateway address. Manager Address Info Displays management station's IP address. Reset Reset the switch. Telnet Connect to the switch's telnet service. Bridge Menu From the Bridge menu, you can view and edit information such as forwarding database and spanning tree status. Forwarding Database Displays forwarding database table.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Alarm Table Displays RMON Alarm table. Event Table Displays RMON Event table. Event Log Displays RMON Event log. VLAN Menu From the VLAN menu, you can view the list of VLAN and member ports. Note - You cannot modify VLAN configuration on the AT-9006 Family using the VLAN menu. Name List Displays configured VLAN names. Port Info Displays VLAN to which the port belongs. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9410GB This section describes AT-View Plus Device Manager menus and operations specific to the AT9410GB switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-9410GB Device Manager LEDs for AT-9410GB LED State Description PWR Green The switch is receiving power. DUPLEX Green The port is operating at full-duplex mode. Orange The port is operating at half-duplex mode.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - When Global STP is enabled, the current firmware version sets the Port State parameter of inactive ports to 'blocking'. As a result, expect port images for inactive ports to turn yellow in ATView Plus Device Manager. Note - When a port on the AT-9410GB is set to 'auto sense' and is connected to a half-duplex port on another device, its corresponding Duplex LED on the device image turns green instead of orange.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT DHCP Info Displays DHCP information including the DHCP System Group and DHCP Timer Group. Reset Resets the switch. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - When connection is established between a twisted pair port that is configured to autonegotiate and a port on another device that is configured to operate at 10/100Mbps full/half duplex, expect the link to drop when the twisted pair port's speed and mode is changed to match the speed and mode of the port on the other device. Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-FH800u This section describes AT-View Plus Device Manager menus and operations specific to the ATFH812u and AT-FH824u hubs. Topics: • • • • • • Main Window Agent Menu Hub Menu Module Menu RMON Menu Port Menu Main Window AT-FH800u Series Device Manager LEDs for AT-FH800u LED State Description PWR Green The hub is receiving power.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Network Info Displays network-related information such as the device's IP address, and the default gateway address.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Hub Menu From the Hub menu, you can check traffic statistics and hub's status. It also lets you perform a selftest. Status Displays hub information such as stacking status. Module Menu From the Module menu, you can view and edit MIB information about a selected hub in the stacked group. Status Displays information such as operation status and object identifier.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Segment Status Displays RMON configuration information of each segment. Port Menu From the Port menu, you can view and edit MIB information about hub's ports. Statistics Displays port statistics such as number of frames received/transmitted on the port, bytes received/transmitted on the port and port status. Status Displays whether the port is enabled or disabled, whether it is partitioned and other status information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR200E This section describes AT-View Plus Device Manager menus and operations specific to the ATAR240E, AT-AR250E, and AT-AR255E ADSL bridge/routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR250E AT-AR255E Device Manager LEDs for ADSL Bridge/Router LED State Description PWR Green The router is receiving power. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The port speed displayed on the Ethernet port images is always '100' even if the Ethernet port is connected to a 10Mbps port on another device. Note - The four Ethernet ports on the AT-AR250E and AT-AR255E operate as a single port. As a result, even if connection is established on just one port, all four ports will turn green. Note - Expect the ADSL port to be green even if there is no physical connection established.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Note - The current firmware version does not allow the user to configure the Physical Address parameter. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: gen Error." Address Table Displays the list of IP interfaces and their IP addresses on the router.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT UDP Statistics Displays UDP statistics. TCP Statistics Displays TCP statistics. Note - The current firmware version does not allow the user to configure the TCP Connection State parameter. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ATUR Channels Displays ATUR Channel information like interleave delay, transmit rate, and length of the channel data-block. ATUR Performance Data Displays ATUR performance statistics like frame failures, signal failures and power failures. Note - The ATUR Performance Data sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ATM Menu From the ATM menu, you can view and edit ATM and AAL5-related information such as ATM interfaces, ATM virtual links, ATM cross-connects, AAL5 entities, and AAL5 connections. Interface Configuration Displays ATM interface configuration information.
Allied Telesyn • • • • AT-VIEW PLUS DEVICE MANAGEMENT Parameter 4 Parameter 5 QoS Class Status Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error." Virtual Path Link (VPL) Displays configuration and state information for a bi-directional Virtual Path Link. Note - The Virtual Path Link (VPL) sub-menu option does not display the correct parameters.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Virtual Path (VP) Cross Connect Displays configuration and state information of all point-to-point , point-to-multipoint, or multipoint-to-multipoint VP cross connect. Note - The Virtual Path (VP) Cross Connect sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the following parameters to be configured: Receive ACC Map Transmit ACC Map Magic Number FCS Size Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: bad value." PPP Link Quality Report LQR Info Displays Link Quality Report information for a particular PPP link. Note - The LQR Info sub-menu option does not display the correct parameters.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridging Configuration Info Displays bridging configuration information for a particular PPP link. Note - The current firmware version does not allow the Administration Status parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PPP Security Security Configuration Info Displays the security configuration information for a particular PPP link. Note - The current firmware version does not allow the Protocol parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied. Note - The current firmware version does not allow the Status parameter to be configured.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT of the ports. For ports 1 to 3, the Administration Status parameter cannot be configured. Its value is fixed to 'up'. For ports 5 to 12, valid MIB Set values for the Administration Status parameter are 'up' and 'down'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300 and AT-AR300L This section describes AT-View Plus Device Manager menus and operations specific to the ATAR300 and AT-AR300L routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300L Device Manager LEDs for AT-AR300 and AT-AR300L LED State Description PWR Green The router is receiving power. B1 Green Data or voice is being transmitted over the B1 channel of the ISDN interface. Gray B2 Green Gray No data or voice is being transmitted over the B1 channel or if the device is connected to a frame relay network. Data or voice is being transmitted over the B2 channel of the ISDN interface.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router. Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT DLCMI Info Displays DLCMI (Data Link Connection Management Interface) information. Circuit Info Displays Frame Relay circuit statistics. Error Info Displays information about errors related to the Frame Relay module. Call List Menu From the Call List menu, you can view ISDN call information. Detail Info Displays ISDN call information such as ISDN nubmer and call direction. Spanning Tree Info Displays information about currently active ISDN calls.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR320 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR320 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR320 Device Manager LEDs for AT-AR320 LED State Description PWR Green The router is receiving power.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR350 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR350 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR350 Device Manager LEDs for AT-AR350 LED State Description PWR Green The router is receiving power.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR370(S) and AT-AR370(U) routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370(U) Device Manager LEDs for AT-AR370(S) and AT-AR370(U) LED State Description PWR Green The router is receiving power. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view and edit ISDN call information. The Call List submenus are greyed out if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN nubmer and call direction. Active Call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR410 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR410 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR410 with PIC installed Device Manager LEDs for AT-AR410 LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Spanning Tree Info Displays the port's spanning tree parameters.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR450S This section describes AT-View Plus Device Manager menus and operations specific to the ATAR450S router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR450S Device Manager LEDs for AT-AR450S LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex. Gray The port is either inactive or is operating at half-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR720 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR720 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR720 with PICs installed Device Manager LEDs for AT-AR720 LED State Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters. This option is greyed out if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725 This section describes AT-View Plus Device Manager menus and operations specific to AT-AR725 and AT-AR725-DC routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725-DC Device Manager LEDs for AT-AR725 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-AR725 AC only) File List Displays a list of the files in the router's flash file system.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are unavailable if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters. This option is unavailable if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR740 and AT-AR740-DC routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740-DC Device Manager LEDs for AT-AR740 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. RPS Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Device Manager LEDs for AT-AR740-DC LED State Description PWR Green The router is receiving power from the main power supply unit.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Note - Please refer to Network Service Modules (NSMs) for the operations and behavior of the Network Service Modules installed in this device. Note - Before hotswapping in the NSM bay, make sure periodic device polling is enabled (File menu -> Properties).
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR745 and AT-AR745-DC routers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745-DC Device Manager LEDs for AT-AR745 LED State Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. RPS Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Device Manager LEDs for AT-AR745-DC LED State Description PWR Green The router is receiving power from the main power supply unit.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Note - Please refer to Network Service Modules (NSMs) for the operations and behavior of the Network Service Modules installed in this device. Note - Before hotswapping in the NSM bay, make sure periodic device polling is enabled (File menu -> Properties).
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are unavailable if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8724XL This section describes AT-View Plus Device Manager menus and operations specific to the AT8724XL and AT-8724XL-DC Advanced Layer 2 Switches. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-8724XL Device Manager LEDs for AT-8724XL LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Device Manager LEDs for AT-8724XL-DC LED State Description PWR Green The switch is receiving power. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-8724XL AC model only) File List Displays a list of the files in the switch's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8748XL This section describes AT-View Plus Device Manager menus and operations specific to the AT8748XL and AT-8748XL-DC Advanced Layer 2 Switches. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-8748XL Device Manager LEDs for AT-8748XL LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Device Manager LEDs for AT-8748XL-DC LED State Description PWR Green The switch is receiving power. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-8748XL AC model only) File List Displays a list of the files in the switch's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Connects to the switch's Telnet server. WEB browser Opens your web browser and connects to the switch's HTTP server.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded for reasons such as lack of memory or the entry's aging timer. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8824 This section describes AT-View Plus Device Manager menus and operations specific to the AT8824 Intelligent Workgroup Switch. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-8824 Device Manager LEDs for AT-8824 LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Grey There is no link over the port. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Reset Warm Performs a warm start of the software modules and executes the default configuration file. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8848 This section describes AT-View Plus Device Manager menus and operations specific to the AT8848 Intelligent Workgroup Switch. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-8848 Device Manager LEDs for AT-8848 LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/MT and 16F/SC This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 16F/MT and Rapier 16F/SC Layer 3 Fast Ethernet Switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/SC Device Manager LEDs for Rapier 16F/MT and Rapier 16F/SC LED State Description PWR Green The switch is receiving power from the main power supply. Red The main power supply has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Network Service Modules for the operations and behavior of the NSM installed in this device. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if the device is not configured for ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24 and 24i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 24 and Rapier 24i Layer 3 Fast Ethernet Switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24i Device Manager LEDs for Rapier 24 and 24i LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. RPS Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Uplink Modules for the operations and behavior of the uplink modules installed in this device. Note - Please refer to Network Service Modules for the operations and behavior of the NSM installed in this device. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the switch. Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48 and 48i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 48 and Rapier 48i Layer 3 Switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48i Device Manager LEDs for Rapier 48 and 48i LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. RPS Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on. Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ICMP Statistics Displays statistics about ICMP, such as the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6 This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6 Layer 3 Gigabit Ethernet Switch. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window Rapier G6 Device Manager LEDs for Rapier G6 LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch. Address Table Displays the list of IP interfaces on the switch. Route Table Displays the IP routing table on the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics. Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-LX/SC, G6F-SX/SC, G6F-SX/MTRJ This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6F-LX/SC, Rapier G6F-SX/SC and Rapier G6F-SX/MT-RJ Layer 3 Gigabit Ethernet Switches.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-SX/SC Rapier G6F-SX/MT-RJ Device Manager LEDs for Rapier G6F LED State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch. Address Table Displays the list of IP interfaces on the switch. Route Table Displays the IP routing table on the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics. Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8948 This section describes AT-View Plus Device Manager menus and operations specific to the AT8948 Enhanced Layer 3+ Switch. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-8948 Device Manager LEDs for AT-8948 LED State PWR 1 and Green PWR 2 Description There is a power supply unit (PSU) in the PSU bay, and it is supplying power to the switch.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT bay. Gray Either: Red - there is no PSU or FOM in the PSU bay, or - a PSU is installed but has a power supply or fan fault or its temperature has exceeded its recommended threshhold (75 degrees C), or - an FOM is installed and a fan has failed. Duplex Green The port is operating at full duplex. Orange The port is operating at half duplex. Gray There is no link over the port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Reset Cold Reset Cold resets the hardware and executes the default configuration file. Reset Warm performs a warm start of the software modules and executes the default configuration file.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4004 This section describes AT-View Plus Device Manager menus and operations specific to the SwitchBlade 4004, including the AT-SB4211 Switch Controller, power supply units and fan tray installed in it.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window SwitchBlade 4004AC with SB4211 Switch Controller, SB4215 Bandwidth Expander, and Line Cards installed PN 613-50665 Rev A Page 187 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-SB4211 Switch Controller LED State Description PWR Green The PSU is receiving power from its supply circuit. MASTER Orange The card is the master switch controller. Gray The card is a slave switch controller. Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis board, and switch controller and line card boards installed in the device. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. For each Port menu option, select first the slot in the SwitchBlade chassis, then the ports in the line card for which you require information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4008 This section describes AT-View Plus Device Manager menus and operations specific to the SwitchBlade 4008, including the AT-SB4211 Switch Controller, power supply units and fan tray installed in it.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4008 with SB4211 Switch Controller and Line Cards installed PN 613-50665 Rev A Page 192 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-SB4211 Switch Controller LED State Description PWR Green The PSU is receiving power from its supply circuit. MASTER Orange The card is the master switch controller. Gray The card is a slave switch controller. Green The port is operating at full duplex. Orange The port is operating at half duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis board, and switch controller and line card boards installed in the device. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. For each Port menu option, select first the slot in the SwitchBlade chassis, then the ports in the line card for which you require information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade Line Cards This section describes the SwitchBlade Line Cards in AT-View Plus Device Manager. If the following Line Cards are installed in a SwitchBlade chassis, they are displayed in the main window. The operations available for the SwitchBlade include any of these line cards.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-SB4411 8-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-SB4412 24-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-SB4451 8-Port (SC) 1000BASE-SX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4452 8-Port (MT-RJ) 1000BASE-SX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4461 8-Port (SC) 1000BASE-LX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9812T This section describes AT-View Plus Device Manager menus and operations specific to the AT9812T, AT-9812TF and AT-9812T-DC Multi-Layer Gigabit Switches. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-9812T Device Manager LEDs for AT-9812T, AT-9812TF, and AT-9812T-DC LED State Description PWR Green The switch is receiving power from the main power supply.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Note - AT-9812T, AT-9812TF and AT-9812T-DC share the same device image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Reset Cold Resets the hardware and executes the default configuration file.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9816GB This section describes AT-View Plus Device Manager menus and operations specific to the AT9816GB, AT-9816GF and AT-9816GB-DC Multi-Layer Gigabit Switches. Topics: Main Window Agent Menu Routing Menu Bridge Menu Port Menu • • • • • Main Window AT-9816GB Device Manager LEDs for AT-9816GB, AT-9816GF, and AT-9816GB-DC LED State Description PWR Green The switch is receiving power from the main power supply.
Allied Telesyn RPS Green AT-VIEW PLUS DEVICE MANAGEMENT The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. DUPLEX Green The port is operating at full duplex. Orange The port is operating at half duplex. Note - AT-9816GB, AT-9816GF and AT-9816GB-DC share the same device image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Reset Cold Resets the hardware and executes the default configuration file. Reset Warm Performs a warm start of the software modules and executes the default configuration file.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF06 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF06 family of media converters. Topics: • • • Main Window Agent Menu Status Menu Main Window AT-MCF06 Family Device Manager LEDs for AT-MCF06 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT but not powered on. NORM Green TEST The unit is not performing a link test. Gray The unit is performing a link test. Green The unit is performing a link test. Gray The unit is not performing a link test. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button. Agent Menu From the Agent Menu, you can view and edit the system information for the device, or log into the CLI using Telnet.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter. Status Menu From the Status Menu, you can view all channels or per channel information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF12 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF12 family of media converters. Topics: • • • Main Window Agent Menu Status Menu Main Window AT-MCF12 Family Device Manager LEDs for AT-MCF12 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on.
Allied Telesyn RPS AT-VIEW PLUS DEVICE MANAGEMENT Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. NORM Green TEST The unit is not performing a link test. Gray The unit is performing a link test. Green The unit is performing a link test. Gray The unit is not performing a link test. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12. Telnet Starts a Telnet connection to the media converter. Status Menu From the Status Menu, you can view all channels or per channel infomation.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF106 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF106 family of media converters. Topics: • • • Main Window Agent Menu Status Menu Main Window AT-MCF106 Family Device Manager LEDs for AT-MCF106 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT but not powered on. NORM Green TEST The unit is not performing a link test. Gray The unit is performing a link test. Green The unit is performing a link test. Gray The unit is not performing a link test. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button. Agent Menu From the Agent Menu, you can view and edit the system information for the device, or log into the CLI using Telnet.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter. Status Menu From the Status Menu, you can view all channels or per channel information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF112 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF112 family of media converters. Topics: • • • Main Window Agent Menu Status Menu Main Window AT-MCF112 Family Device Manager LEDs for AT-MCF112 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on.
Allied Telesyn RPS AT-VIEW PLUS DEVICE MANAGEMENT Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. NORM Green TEST The unit is not performing a link test. Gray The unit is performing a link test. Green The unit is performing a link test. Gray The unit is not performing a link test. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12. Telnet Starts a Telnet connection to the media converter. Status Menu From the Status Menu, you can view all channels or per channel information.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MPB3000 This section describes AT-View Plus Device Manager menus and operations specific to the ATMPB3000 chassis.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-MPB3000 Note - The current firmware version does not allow AT-View Plus Device Manager to support stacked AT-MPB3000 devices. Device Manager LEDs for AT-MPB3000 LED State Description PWR1 Green Power supply 1 is installed and power is on. Gray Power supply 1 is not installed or it is installed but not powered on.
Allied Telesyn PWR2 RPS AT-VIEW PLUS DEVICE MANAGEMENT Green Power supply 2 is installed and power is on. Gray Power supply 2 is not installed or it is installed but not powered on. Green The optional redundant power supply is installed and power is on. Gray The optional redundant power supply is not installed or it is installed but not powered on. Agent Menu From the Agent Menu, you can view and edit the system information for the chassis, or log into the CLI using Telnet.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MPB3000 Modules This section describes the modules supported by AT-View Plus Device Manager. If modules are installed on the AT-MPB3000 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The MCM100-02 module image applies to the following variants: • • • • AT-MCM100-02SC AT-MCM100-02SMR AT-MCM100-02SMRF15 AT-MCM100-02ST AT-MCM110 Modules MCM110-01 MCM110-02 LED State Description RAD Green The FX port is connected to a remote access device.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCM1000S Modules MCM1000S LED State Description RAD Green The LX port is connected to a remote access device. Note - The TP Link Status parameter reflects the status of the SX port while the F/O Link Status parameter reflects the status of the LX port. Note - The remote access device connected to the LX port may at times be inaccessible when link is established on the SX port.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCM1000T Modules MCM1000T LED State Description RAD Green The LX port is connected to a remote access device.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade This section describes AT-View Plus Device Manager menus and operations specific to the ATPBC18 chassis.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-PBC18 LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The optional redundant power supply is installed and power is on. Gray The optional redundant power supply is not installed or it is installed but not powered on.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Info Displays power supply voltage information. Battery Voltage Displays the battery voltage information. Omega Displays Omega management interface information, including time-out and port status (RS232 and 10Base-T). Telnet Starts a Telnet connection to the chassis. Status Menu From the Status Menu, you can view and edit information about PowerBlade Modules installed on the chassis. Options to view all/per module information are displayed.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade Modules This section describes the modules supported by AT-View Plus Device Manager. If modules are installed on the PowerBlade chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB100 Series Media Converter Modules PB101 PB102 PB103/1 PB103/2 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - The Port A Mode parameter for these modules has a fixed value of 'full' and cannot be modified.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB200 Series Switch Modules PB201 PB202 PB202/1 PB202/3 PB202/4 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The 10/100Base-TX port is auto-negotiating.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB300 Series Media Converter Modules PB301 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - Port A is displayed as an SC connector instead of a VF-45 connector. Note - The Port A Mode parameter for this module has a fixed value of 'full' and cannot be modified.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB1000 Series Media Converter Modules PB1001/1 PB1001/3 LED State Description LT Green Link Test is enabled SML Green Smart Missing Link is enabled ML Green Missing Link is enabled PB1005G Note - Smart Missing Link is only supported on the AT-PB1005G module. However, the current firmware version allows the Link Test parameter of the AT-PB1001/1 and AT-PB1001/3 modules to be set to 'smart-missing-link'.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG213 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATRG213FX and AT-RG213TX Residential VoIP Gateways. Topics: • • • • Main Window Agent Menu RTC Menu Port Menu Main Window AT-RG213 Device Manager LEDs for AT-RG213FX and AT-RG213TX LED State Description PWR Green The residential gateway is receiving power. Note - The AT-RG213FX and the AT-RG213TX share the same device image.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view MIB information about the ethernet and voice ports. Interface Info Ethernet Displays information for each ethernet port. Note - The current firmware version returns 'not available' for the following parameters: Port Link State Port Type Port Speed Port Duplex Mode Port Autonegotiation State Voice Displays information for each voice port. Information displayed will vary depending on the protocol used : H.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Suspicion Threshold Port Disconnection Threshold Port Initial Retransmission Delay Port Maximum Retransmission Delay Port History Time Port Maximum Propagation Delay Note - SIP : The current firmware version returns 'Not Available' for the Port Registration Time parameter.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG600 Series This section describes AT-View Plus Device Manager menus and operations specific to the ATRG613SH, AT-RG613TX, AT-RG634A and AT-RG656BD Residential Gateways.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG613TX AT-RG634A PN 613-50665 Rev A Page 239 of 257
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG656BD Device Manager LEDs for AT-RG600 Series LED State Description PWR Green The residential gateway is receiving power. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - The current firmware version does not allow AT-View Plus Device Manager to determine the negotiated mode for active LAN or WAN ports that are configured to auto-negotiate. As a result, the Duplex LED will turn gray.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - The current firmware version does not allow the user to enter multiple-word values for the System Name parameter. Attempting to do so will result in the error message: "The error occurred with 'Set' operation.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT operation. Error: Time out occurred." After which, the value for the parameter is then reverted back to its default value. If GSPAN is loaded on the device, the same behavior may occur when the Comment or Password parameters are set to a string that is more than 65 characters long and more than 84 characters, respectively, Note - AT-RG656BD: Valid MIB Set values for the Comment parameter are in the range [089] inclusive.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG634A: Valid MIB Set values for the Aging Time Value parameter are in the range [0-2147483647] inclusive. Attempting to set this parameter to any value will not result in an error, but the new value will not be applied. Note - AT-RG656BD: The current firmware version does not allow the Learning Status parameter to be set to 'disable'. Attempting to do so will result in the error message: "The error occurred with 'Set' operation.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG634A: Valid MIB Set values for the Leave Time parameter are in the range [065535] inclusive. Setting this parameter to a valid or invalid value always results in the error message: "The error occurred with 'Set' operation. Error: commit Failed." VLAN Info Displays the VLAN table. Group Info Displays a list of all group multicast address. Server Info Displays a list of all multicast servers.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT MGCP Protocol Info Displays general information about the protocol. Note - Valid MIB Set values for the Default Port parameter are in the range [10242147483647] inclusive. Attempting to set this parameter to a value outside the valid range will not result in an error but the new value will not be applied. Note - When setting the Profile parameter to 'none', the current firmware is able to set the parameter successfully for the CLI but not for SNMP.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Valid MIB Set values for the Port Speed and Mode parameter of the 100Base-FX WAN ports should only be '100Mbps full-duplex', '100Mbps half-duplex', and 'auto sense'. However, the current firmware version allows it to be set to '10Mbps full-duplex' or '10Mbps half-duplex' as well.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - AT-RG656BD : By default, the WAN port is enabled. However, once disabled, it can no longer be enabled until the device is reset to factory defaults. Note - If the user has no read access to the Admin Info MIB group, the association of the End-Point to the Voice Port may be incorrect when accessing the different context menu options: Dial Info Call Forwarding Info CLI Info Quality Info Statistics As a result, when a user right clicks on a Voice Port (eg.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Interface Cards This section describes the following Port Interface Cards supported in AT-View Plus Device Manager : • • • • • • • AT-AR020 AT-AR021 AT-AR022 AT-AR023 AT-AR024 AT-AR026 AT-AR027 If one of these PICs is installed in a PIC bay of a Router (AT-AR400 series or AT-AR700 series), or in a Network Service Module (NSM) of a Router or Layer 3 Switch (Rapier series), it is displayed in the PIC bay of the device in the main window.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR021(S) and AT-AR021(U) LED State B1 and B2 Green Gray Description For permanent circuits, HDLC packets are being exchanged between the switch or router and another end system device (normally another switch or router) over any of the B channel. For on-demand ISDN, there is a call up over the respective Bchannel. No packet/data transmission over B-channel. AT-AR022 Note - There are no LEDs on this PIC.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The four physical ports in this PIC are configured and behave as one ETH port from the viewpoint of the software running on the device. AT-AR027 Note - There are no LEDs on this PIC.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Service Modules This section describes the following Network Service Modules (NSMs) supported in AT-View Plus Device Manager. AT-AR040 4-PIC slot NSM Note - Up to four Port Interface Cards can be installed in the AT-AR040 NSM. Note - There are no LEDs on this NSM.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR041 and AT-AR042 LED State Data LEDs Orange Gray Description For permanent circuits, HDLC packets are being exchanged between the switch or router and another TE end system device (normally another switch or router) over the respective Bchannel. For on-demand ISDN, there is a call up over the respective B-channel. No packet/data transmission over B-channel.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Uplink Modules This section describes the Uplink Modules that can be installed in Layer 2 Switches, Advanced Layer 2 Switches, and Layer 3 Switches. Topics : • • Layer 2 Switches Uplink Modules Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules Layer 2 Switches Uplink Modules If the uplink modules are installed in one of the Layer 2 switches, they are displayed in the uplink bays of the device in the main window.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-A16 Device Manager LEDs for AT-A16 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A17 Device Manager LEDs for AT-A17 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A18 Device Manager LEDs for AT-A18 LED State Description DUPLEX Green The port is operating at full-duplex.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-A19 LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A16/AT-A17/AT-A19 Device Manager LEDs for AT-A16/AT-A17/AT-A19 LED State Description DUPLEX Green The port is operating at full- duplex. Orange The port is operating at half-duplex. AT-A45/AT-A47/AT-STACKM Note - There are no LEDs on this module.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules If the uplink modules are installed in one of the Rapier series or AT-8700XL series switches, they are displayed in the uplink bays of the device in the main window. The operations available for the main device include any of these uplink modules. AT-A35 Note - There are no LEDs on this module.
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-A41 Device Manager LEDs for AT-A41/MT and AT-A41/SC LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A42/GBIC Device Manager LEDs for AT-A42/GBIC LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.
