Owner's manual

ManualsBrandsAllied Telesis ManualsComputer HardwareAT-VIEW PLUS 2.3 DEVICE MANAGEMENT

PN 613-50507-00 Rev C Page 1 of 224

AT-VIEW PLUS 2.3

DEVICE MANAGEMENT GUIDE

Summary of content (224 pages)

PAGE 1
AT-VIEW PLUS 2.
PAGE 2
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Copyright (c) 2003-2004 Allied Telesis K. K. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, K. K. Microsoft is a registered trademark of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.
PAGE 3
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT TABLE OF CONTENTS Basic Operations ................................................................................................................ 10 Common operations on the main window....................................................................... 11 Menu for stacked devices ............................................................................................... 11 Port selection dialog box.....................................................
PAGE 4
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu .................................................................................................................... 50 Bridge Menu ................................................................................................................... 51 RMON Menu................................................................................................................... 51 Port Menu ................................................................
PAGE 5
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu .................................................................................................................... 88 Routing Menu ................................................................................................................. 88 Bridge Menu ................................................................................................................... 90 ADSL Menu ..............................................................
PAGE 6
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Routing Menu ............................................................................................................... 117 Bridge Menu ................................................................................................................. 118 Port Menu ..................................................................................................................... 118 AT-AR720 ................................................................
PAGE 7
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu ..................................................................................................................... 145 Rapier 16F/MT and 16F/SC ............................................................................................. 146 Main Window ................................................................................................................ 146 Agent Menu .....................................................................
PAGE 8
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu ..................................................................................................................... 179 SwitchBlade Line Cards ................................................................................................... 180 AT-9812T ......................................................................................................................... 183 Main Window ..........................................................
PAGE 9
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR020..................................................................................................................... 215 AT-AR021..................................................................................................................... 215 AT-AR022..................................................................................................................... 216 AT-AR023..................................................................
PAGE 10
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT This document describes the operations and menus specific to particular Allied Telesyn models of managed devices. For module-independent information, refer to the AT-View Plus Device Manager User's Guide. Basic Operations AT-View Plus Device Manager's main window shows the main panel of the target device. It has both common and device-specific menus on its menu bar.
PAGE 11
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Common operations on the main window Right clicking on a port Port Right clicking on a port opens a pull-down menu specific to the device. Selecting a menu item opens another window and lets you view and edit MIB information related to the port. You can also access the same menu from the menu bar. RS-232 Terminal Port Right clicking on an RS-232 port opens a pull-down menu and lets you choose how to log into the agent.
PAGE 12
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Module submenu PN 613-50507-00 Rev C Page 12 of 224
PAGE 13
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port selection dialog box When you select a menu item acting on ports, a dialog box opens to let you select ports. Check the target ports and click OK. Note - If you select multiple ports, it may take some time for data to be displayed. Select Port dialog box Port status colors Port status is shown by its color. Port speed is also displayed in the port image.
PAGE 14
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Utilization Utilization is calculated by the following formula.
PAGE 15
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8000 Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8000 Series (excluding the AT-8026T).
PAGE 16
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8016F/MT AT-8016F/SC PN 613-50507-00 Rev C Page 16 of 224
PAGE 17
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8016F/ST AT-8024 PN 613-50507-00 Rev C Page 17 of 224
PAGE 18
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8024GB AT-8024M PN 613-50507-00 Rev C Page 18 of 224
PAGE 19
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8026FC AT-8088/MT PN 613-50507-00 Rev C Page 19 of 224
PAGE 20
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8088/SC Device Manager LEDs for AT-8000 Series LED State Description PWR Green The switch is receiving power. MASTER Orange Gray DUPLEX Green Orange The switch is the master switch of an enhanced stack. The switch is a slave switch or is not a member of an enhanced stack. The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 21
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Connection between an AT-8024GB and an AT-8324 can only be established if the uplink ports on both devices are configured to auto-negotiate. Note - When a port's Port Speed and Mode parameter is set to 'auto sense' and the port is connected to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.
PAGE 22
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Default Domain Name and the DNS Server parameters to be configured. Manager Address Info Displays the IP address of the management station. Device Info Displays general information about the switch. MAC Address Table Displays a list of static MAC addresses configured on the switch.
PAGE 23
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table.
PAGE 24
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Error Statistics Displays error statistics. Detail Info Displays detailed port information such as duplex mode. Note - Setting the Port Reset parameter to 'reset' will not reset the port's attributes. Note - Valid MIB Set values for the Port Flow Control parameter are 'disable', 'transmitonly', 'receive-only', and 'transmit-and-receive'.
PAGE 25
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Under the Sun Solaris platform, the AT-View Plus Device Manager application may terminate abnormally if multiple ports have been selected and each dialog box with the message "May I set 'atiswitchPortState.n' to down" is clicked one after the other. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.
PAGE 26
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT • When the Port Speed and Mode parameter of the AT-A46 expansion module port is set to "auto 10/100Mbps" and the port is connected to a 10/100Mbps full-duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green. • The Spanning Tree Protocol (STP) does not work for the AT-A46 expansion module when it is installed on an AT-8016F/ST device.
PAGE 27
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124 This section describes AT-View Plus Device Manager menus and operations specific to the AT8124 switch.
PAGE 28
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-8124 LED State Description PWR Green The switch is receiving power. DUPLEX Green Gray The port is operating in full-duplex mode. The port is operating in half-duplex mode. Agent Menu From the Agent menu, you can view and edit the system information for the device or log into the CLI using telnet. System Info Displays basic system information, including system name, location, contact and description.
PAGE 29
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 30
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Detail Info Displays port traffic statistics such as the number of frames received/transmitted on the port. Error Statistics Displays error information.
PAGE 31
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8124XL (V2) This section describes AT-View Plus Device Manager menus and operations specific to the AT8124XL (V2) switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-8124XL (V2) Device Manager LEDs for AT-8124XL (V2) LED State Description PWR Green The switch is receiving power. DUPLEX Green Orange PN 613-50507-00 Rev C The port is operating in full-duplex mode. The port is operating in half-duplex mode.
PAGE 32
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the System Contact, System Name, and System Location parameters but truncates them to 64 characters. NULL values are not accepted.
PAGE 33
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch's ports. RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table.
PAGE 34
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Attempting to modify the Port Speed and Mode parameter from 'auto sense' to '1Gbps half-duplex' or '1Gbps full-duplex' will result in the following: • • An error message: "The error occurred with 'Set' operation. Error: gen Error" Port Speed and Mode parameter value changing to '100Mbps half-duplex' Note - The current firmware version does not allow the Port Bridge ID parameter to be configured.
PAGE 35
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8200XL Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8216FXL/SC and AT-8224XL switches.
PAGE 36
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8224XL Device Manager LEDs for AT-8200XL Series LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating at full-duplex mode. The port is operating at half-duplex mode.
PAGE 37
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version allows the user to enter up to 64 characters for the System Contact and the System Location parameters and up to 20 characters for the System Name parameter. Note - The current firmware version appends a period '.' and the value of the Default Domain Name parameter to the value of the System Name parameter. Firmware Info Displays the firmware version of the switch.
PAGE 38
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT DHCP Info Displays the DHCP information about the switch. Diagnostics Displays the operating status of the switch's components such as power supply and system fans. Note - The current firmware version returns 'non-supported' for the following parameters: • • • • • • Fan Speed 3 3.3V Power 2.5Va Power 2.5Vb Power 2V Power CPU Temperature Reset Resets the switch. Console Settings Displays the current settings of the console.
PAGE 39
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the VLAN Name parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName." Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 40
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value." Error Statistics Displays error statistics. Detail Info Displays detailed port information such as duplex mode. Note - The Port Flow Control parameter has a fixed value of 'not supported' and cannot be modified.
PAGE 41
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Expansion Module Notes • When the Port Speed and Mode parameter of an AT-A14 expansion module port is set to 'auto sense' and the port is connected to a 100Mbps full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green. • The current firmware version does not allow the Port Speed and Mode parameter of the ATA14 expansion module port to be set to any value other than 'auto-sense'.
PAGE 42
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324 This section describes AT-View Plus Device Manager menus and operations specific to the AT8324 switch.
PAGE 43
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Supports up to 8 stacked AT-8324 switches. LED State PWR Green DUPLEX Green Orange Device Manager LEDs for AT-8324 Description The switch is receiving power. The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - The current firmware version does not allow AT-View Plus Device Manager to support the RPS and the Master LEDs.
PAGE 44
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because of lack memory or the entry's aging timer has expired.
PAGE 45
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version is unable to retrieve the correct information for the History Control Table. As a result, the following error message appears: "Failed to get MIB data." Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 46
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Port State parameter returns 'unknown' for active ports. Note - When a port is configured to auto-negotiate, the current firmware version does not always update its Port Duplex Status parameter with the correct negotiated mode. As a result, the port's Duplex LED may show up as green when it should really be orange and vice-versa.
PAGE 47
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Stacking Menu From the Stacking menu, you can view basic switch information as well as stacking information. Stacking Info Displays information such as Product Type, Port Count and Uplink Types for all switches in the stack.
PAGE 48
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8324SX This section describes AT-View Plus Device Manager menus and operations specific to the AT8324SX switch.
PAGE 49
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8324SX Supports up to 4 stacked switches.
PAGE 50
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Device Manager LEDs for AT-8324SX Description PWR Green The switch is receiving power. RPS Green Redundant power is ON. Gray Redundant power is OFF. DUPLEX Gray STACK ID The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode. Green The switch's position in the switch stack. Note - When multiple units of AT-8324SX are stacked together, port numbering is continuous.
PAGE 51
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information, such as the forwarding database and spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 52
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Displays the RMON event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Note - The current firmware version does not allow Port Menu to support the Class of Service. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 53
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination. IGMP Snooping Displays the current state of IGMP Snooping and allows reconfiguration. Note - Valid MIB Set values for the IGMP Report Delay parameter should range from 5 to 30.
PAGE 54
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8300GB Series This section describes AT-View Plus Device Manager menus and operations specific to the AT8300GB Series.
PAGE 55
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8326GB PN 613-50507-00 Rev C Page 55 of 224
PAGE 56
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT The AT-8326GB supports up to 6 AT-8326GB stacked switches or any of the following mixed stack combinations of AT-8326GB and AT-8350GB switches: • • • • Two AT-8326GB switches and one AT-8350GB switch Two AT-8326GB switches and two AT-8350GB switches Three AT-8326GB switches and one AT-8350GB switch Four AT-8326GB switches and one AT-8350GB switch Note - When 3 or more AT-8326GB devices are stacked together, expect the twisted pair port image of Port 26 on th
PAGE 57
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow AT-View Plus Device Manager to support expansion modules that may be installed on the AT-8350GB. LED State PWR Green Device Manager LEDs for AT-8300GB Series Description The switch is receiving power. STACK ID Green The switch's position in the switch stack. DUPLEX Green The port is operating in full-duplex mode. Orange The port is operating in half-duplex mode.
PAGE 58
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Info Displays network-related information such as the device IP address and the default gateway address. Note - The current firmware version does not save changes made to the DNS Server and the Default Domain Name parameters. DHCP Info Displays DHCP information including the DHCP System Group and DHCP Timer Group. Manager Address Info Displays the IP address of the management station. Reset Resets the switch.
PAGE 59
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT RMON Menu From the RMON menu you can view and edit the RMON MIB. Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON History table. Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 60
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Port Bridge ID parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value". Note - When a port's Port Speed and Mode parameter is set to 'auto sense', the current firmware version does not update its Port Duplex Status parameter with the negotiated mode.
PAGE 61
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The Security Action parameter returns '???(0)' when the Security Configuration parameter is set to 'disabled'.
PAGE 62
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 This section describes AT-View Plus Device Manager menus and operations specific to the AT8400 switch.
PAGE 63
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window AT-8400 PN 613-50507-00 Rev C Page 63 of 224
PAGE 64
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED Device Manager LEDs for AT-8401 Management Module State Description FAN A Green FAN TRAY A is installed and is operating correctly. Gray FAN TRAY A is not installed. Green FAN TRAY B is installed and is operating correctly. Gray FAN TRAY B is not installed. FAN B MASTER Green RPS The switch is the master of an enhanced stack. Gray The switch is either a slave switch of an enhanced stack or the switch is not a member of an enhanced stack.
PAGE 65
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Network Info Displays network-related information such as the addresses of the default gateway and the agents. Note - The current firmware version does not allow the DNS Server and Default Domain Name parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation.
PAGE 66
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - It may take some time to retrieve Forwarding Database information. As a result, all the Forwarding Database parameters may reflect the value 'retry over occurred'. To avoid this, click on File -> Property -> Polling options and set the Polling Interval parameter to 25 seconds or longer.
PAGE 67
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Note - Ports are numbered continuously from top to bottom, across all installed line cards, starting from the leftmost line card all the way through the rightmost line card.
PAGE 68
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Security Displays the port security attributes for each physical port present in the switch. Enable Enables the port. Disable Disables the port. Port Mirroring Displays port mirroring parameters and allows configuration of port mirroring state and port's source list. Note - Valid MIB Set values for the Port Mirroring Configuration Entry Status parameter are 'active', 'not in service' and 'destroy'.
PAGE 69
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8400 Line Cards This section describes the AT-8400 Line Cards supported by AT-View Plus Device Manager. If line cards are installed on the AT-8400 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image. • • • • AT-8411 AT-8412 AT-8413 AT-8414 AT-8411 AT-8411 LED State Description DUPLEX Green The port is operating in full-duplex.
PAGE 70
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8412 AT-8412/MT AT-8412/SC LED State Description DUPLEX Green The port is operating in full-duplex. Note – The current firmware version does not allow the Port Flow Control parameter of ports on the AT-8412/MT and AT-8412/SC line cards to be set to ‘auto’. Attempting to set this parameter to ‘auto’ will result in the error message: “The error occurred with ‘Set’ operation. Error: gen Error”.
PAGE 71
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8413 AT-8413GB/T LED State Description DUPLEX Green The port is operating in full-duplex. Orange The port is operating in half-duplex. Note - A GBIC image is always visible on the GBIC slot of the AT-8413GB/T line card image even if there is no GBIC physically present in the slot.
PAGE 72
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8414 AT-8414/SC AT-8414/ST LED State Description DUPLEX Green The port is operating in full-duplex. Orange The port is operating in half-duplex. Note - The Port Negotiation parameter of ports on the AT-8414/SC and AT-8414/ST line cards has a fixed value of '10Mbps full-duplex' and cannot be modified.
PAGE 73
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006 Family This section describes AT-View Plus Device Manager menus and operations specific to the AT9006SX/SC and AT-9006T switches.
PAGE 74
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9006T Device Manager LEDs for AT-9006 Family LED State Description PWR Green The switch is receiving power. RPS Green An optional redundant power supply is connected to the switch. Gray There is no redundant power supply connected to the switch. DUPLEX Green Orange The port is operating in full-duplex mode. The port is operating in half-duplex mode. Note - Ports on the expansion modules are numbered starting from 7.
PAGE 75
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Firmware Info Displays firmware version. Network Info Displays network-related information such as agent's and default gateway address. Manager Address Info Displays management station's IP address. Reset Reset the switch. Telnet Connect to the switch's telnet service. Bridge Menu From the Bridge menu, you can view and edit information such as forwarding database and spanning tree status. Forwarding Database Displays forwarding database table.
PAGE 76
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Alarm Table Displays RMON Alarm table. Event Table Displays RMON Event table. Event Log Displays RMON Event log. VLAN Menu From the VLAN menu, you can view the list of VLAN and member ports. Note - You cannot modify VLAN configuration on the AT-9006 Family using the VLAN menu. Name List Displays configured VLAN names. Port Info Displays VLAN to which the port belongs. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 77
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port.
PAGE 78
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9410GB This section describes AT-View Plus Device Manager menus and operations specific to the AT9410GB switch. Topics: • • • • • Main Window Agent Menu Bridge Menu RMON Menu Port Menu Main Window AT-9410GB Device Manager LEDs for AT-9410GB Description LED State PWR Green The switch is receiving power. DUPLEX Green The port is operating at full-duplex mode. Orange The port is operating at half-duplex mode.
PAGE 79
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT inactive ports to 'blocking'. As a result, expect port images for inactive ports to turn yellow in ATView Plus Device Manager. Note - When a port on the AT-9410GB is set to 'auto sense' and is connected to a half-duplex port on another device, its corresponding Duplex LED on the device image turns green instead of orange.
PAGE 80
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 81
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on 'down'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation.
PAGE 82
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Port VLAN Tag Priority parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value.
PAGE 83
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-FH800u This section describes AT-View Plus Device Manager menus and operations specific to the ATFH812u and AT-FH824u hubs. Topics: • • • • • • Main Window Agent Menu Hub Menu Module Menu RMON Menu Port Menu Main Window AT-FH800u Series LED State Device Manager LEDs for AT-FH800u Description PWR Green The hub is receiving power.
PAGE 84
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Network Info Displays network-related information such as the device's IP address, and the default gateway address.
PAGE 85
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Hub Menu From the Hub menu, you can check traffic statistics and hub's status. It also lets you perform a selftest. Status Displays hub information such as stacking status. Module Menu From the Module menu, you can view and edit MIB information about a selected hub in the stacked group. Status Displays information such as operation status and object identifier.
PAGE 86
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about hub's ports. Statistics Displays port statistics such as number of frames received/transmitted on the port, bytes received/transmitted on the port and port status. Status Displays whether the port is enabled or disabled, whether it is partitioned and other status information. Detail Status Displays information such as port name, LED status and polarity.
PAGE 87
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR250E This section describes AT-View Plus Device Manager menus and operations specific to the ATAR250E router. Topics: • • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu ADSL Menu ATM Menu PPP Menu Port Menu Main Window AT-AR250E LED State Device Manager LEDs for AT-AR250E Description PWR Green The router is receiving power. Note - The current firmware version does not allow AT-View Plus Device Manager to support the Reset button.
PAGE 88
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The port speed displayed on the Ethernet port images is always '100' even if the Ethernet port is connected to a 10Mbps port on another device. Note - The four Ethernet ports on the device operate as a single port. As a result, even if connection is established on just one port, all four ports will turn green. Note - Expect the ADSL port to be green even if there is no physical connection established.
PAGE 89
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router. Note - The Address Table sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. Route Table Displays the IP routing table on the router. Note - The current firmware version does not allow the user to configure the Destination Port Number parameter.
PAGE 90
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the user to configure the TCP Connection State parameter. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value." Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database, discard/aging time information, and spanning tree status.
PAGE 91
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ATUR Performace Data by Interval Diplays collection of ATUR performance statistics in 15-minute intervals. Note - The ATUR Performance Data by Interval sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'. ATUR Channel Performance Data Displays ATUR channel performance statistics like received blocks, transmitted blocks, and error counts.
PAGE 92
Allied Telesyn • • • • • AT-VIEW PLUS DEVICE MANAGEMENT Max Active VCI Bits ILMI VPI ILMI VCI Neighbor IP Address Neighbor Name Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error." Interface DS3 PLCP Displays DS3 PLCP configuration and state parameters. Note - The Interface DS3 PLCP sub-menu option does not display the correct parameters.
PAGE 93
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Virtual Channel Link (VCL) Displays configuration and state information for a bi-directional Virtual Channel Link. Note - The Virtual Channel Link (VCL) sub-menu option does not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.
PAGE 94
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Initial MRU parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.
PAGE 95
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT MAC Bridging over PPP Bridging Info Displays information indicating whether the Bridge Network Control Protocol has reached an opened state, the type of compression used, and use of LAN identification field in packets. Bridging Configuration Info Displays bridging configuration information for a particular PPP link. Note - The current firmware version does not allow the Administration Status parameter to be configured.
PAGE 96
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The current firmware version does not allow the Compression parameter to be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName." Note - The current firmware version does not allow the Administration Status parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.
PAGE 97
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Note - The Interface Info sub-menu option displays port parameters for 20 ports. By default, the Administration Status parameter is set to 'up' for the first four ports and 'down' for the rest of the ports. For ports 1 to 3, the Administration Status parameter cannot be configured.
PAGE 98
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300 and AT-AR300L This section describes AT-View Plus Device Manager menus and operations specific to the ATAR300 and AT-AR300L routers.
PAGE 99
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR300L LED Device Manager LEDs for AT-AR300 and AT-AR300L State Description PWR Green The router is receiving power. B1 Green Data or voice is being transmitted over the B1 channel of the ISDN interface. Gray B2 Green Gray No data or voice is being transmitted over the B1 channel or if the device is connected to a frame relay network. Data or voice is being transmitted over the B2 channel of the ISDN interface.
PAGE 100
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router. Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router.
PAGE 101
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Circuit Info Displays Frame Relay circuit statistics. Error Info Displays information about errors related to the Frame Relay module. Call List Menu From the Call List menu, you can view ISDN call information. Detail Info Displays ISDN call information such as ISDN nubmer and call direction. Spanning Tree Info Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
PAGE 102
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR320 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR320 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR320 LED State Device Manager LEDs for AT-AR320 Description PWR Green The router is receiving power.
PAGE 103
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 104
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 105
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR350 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR350 router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR350 LED State Device Manager LEDs for AT-AR350 Description PWR Green The router is receiving power.
PAGE 106
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 107
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 108
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR370(S) and AT-AR370(U) routers.
PAGE 109
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR370(U) LED Device Manager LEDs for AT-AR370(S) and AT-AR370(U) State Description PWR Green The router is receiving power. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system.
PAGE 110
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ARP Table Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router. Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics.
PAGE 111
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view and edit ISDN call information. The Call List submenus are greyed out if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN nubmer and call direction. Active Call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports.
PAGE 112
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR410 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR410 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR410 with PIC installed LED State Device Manager LEDs for AT-AR410 Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
PAGE 113
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems.
PAGE 114
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 115
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Spanning Tree Info Displays the port's spanning tree parameters.
PAGE 116
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR450S This section describes AT-View Plus Device Manager menus and operations specific to the ATAR450S router. Topics: • • • • • Main Window Agent Menu Routing Menu Bridge Menu Port Menu Main Window AT-AR450S LED State Device Manager LEDs for AT-AR450S Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex. Gray The port is either inactive or is operating at half-duplex.
PAGE 117
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash and NVS file systems. Config File Name Displays the file name of the start-up configuration file. Telnet Starts a Telnet connection to the router.
PAGE 118
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 119
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR720 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR720 router. Topics: • • • • • • • Main Window Agent Menu Routing Menu Bridge Menu Frame Relay Menu Call List Menu Port Menu Main Window AT-AR720 with PICs installed LED State Device Manager LEDs for AT-AR720 Description PWR Green The router is receiving power. DUPLEX Green The port is operating at full-duplex.
PAGE 120
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Port Interface Cards (PICs) for the operations and behavior of the Port Interface Cards installed in this device. Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. File List Displays a list of the files in the router's flash file system.
PAGE 121
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are greyed out if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 122
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters. This option is greyed out if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
PAGE 123
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725 This section describes AT-View Plus Device Manager menus and operations specific to AT-AR725 and AT-AR725-DC routers.
PAGE 124
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR725-DC LED State Device Manager LEDs for AT-AR725 Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled.
PAGE 125
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-AR725 AC only) File List Displays a list of the files in the router's flash file system.
PAGE 126
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status. The Bridge submenus are unavailable if bridges are not configured. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.
PAGE 127
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics for the port. Spanning Tree Info Displays the port's spanning tree parameters. This option is unavailable if bridge ports are not configured on the router at the time AT-View Plus Device Manager is started.
PAGE 128
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR740 and AT-AR740-DC routers.
PAGE 129
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR740-DC LED State Device Manager LEDs for AT-AR740 Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. LED State Device Manager LEDs for AT-AR740-DC Description PWR Green The router is receiving power from the main power supply unit.
PAGE 130
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Before hotswapping in the NSM bay, make sure periodic device polling is enabled (File menu -> Properties). Note - To turn RPS monitoring on or off on the router, from the AT-AR740 console enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 131
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status.
PAGE 132
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 133
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745 This section describes AT-View Plus Device Manager menus and operations specific to the ATAR745 and AT-AR745-DC routers.
PAGE 134
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-AR745-DC LED State Device Manager LEDs for AT-AR745 Description PWR Green The router is receiving power from the main power supply unit. Red The main PSU has failed. Green The router is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. LED State Device Manager LEDs for AT-AR745-DC Description PWR Green The router is receiving power from the main power supply unit.
PAGE 135
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Before hotswapping in the NSM bay, make sure periodic device polling is enabled (File menu -> Properties). Note - To turn RPS monitoring on or off on the router, from the AT-AR745 console enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 136
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Address Table Displays the list of IP interfaces and their IP addresses on the router Route Table Displays the IP routing table on the router. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status.
PAGE 137
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.
PAGE 138
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8724XL This section describes AT-View Plus Device Manager menus and operations specific to the AT8724XL and AT-8724XL-DC Advanced Layer 2 Switches.
PAGE 139
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Device Manager LEDs for AT-8724XL Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 140
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-8724XL AC model only) File List Displays a list of the files in the switch's flash file system.
PAGE 141
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 142
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-8748XL This section describes AT-View Plus Device Manager menus and operations specific to the AT8748XL and AT-8748XL-DC Advanced Layer 2 Switches.
PAGE 143
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Device Manager LEDs for AT-8748XL Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 144
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT System Info Displays basic system information, including system name, location, contact and description. Power Supply Info Displays information about the power supply, redundant power supply and power supply monitoring. (AT-8748XL AC model only) File List Displays a list of the files in the switch's flash file system. Config File Name Displays the file name of the start-up configuration file. Telnet Connects to the switch's Telnet server.
PAGE 145
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded for reasons such as lack of memory or the entry's aging timer. Spanning Tree Info Displays spanning tree parameters such as priority and cost.
PAGE 146
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/MT and 16F/SC This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 16F/MT and Rapier 16F/SC Layer 3 Fast Ethernet Switches.
PAGE 147
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 16F/SC LED Device Manager LEDs for Rapier 16F/MT and Rapier 16F/SC State Description PWR Green The switch is receiving power from the main power supply. Red The main power supply has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 148
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Network Service Modules for the operations and behavior of the NSM installed in this device. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 149
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 150
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if the device is not configured for ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction for active calls. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 151
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24 and 24i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 24 and Rapier 24i Layer 3 Fast Ethernet Switches.
PAGE 152
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 24i LED State Device Manager LEDs for Rapier 24 and 24i Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 153
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - Please refer to Network Service Modules for the operations and behavior of the NSM installed in this device. Note - To turn RPS monitoring on or off on the switch, from the switch command line interface enter the command SET SYSTEM RPSMONITOR={ON|OFF}. To see whether RPS monitoring is on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on.
PAGE 154
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Route Table Displays the IP routing table on the switch. IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, including the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 155
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if an ISDN interface is not installed, and the device is not configured to use ISDN. Detail Info Displays ISDN call information such as ISDN number and call direction. Active call Displays information about currently active ISDN calls. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 156
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48 and 48i This section describes AT-View Plus Device Manager menus and operations specific to the Rapier 48 and Rapier 48i Layer 3 Switches.
PAGE 157
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier 48i LED State Device Manager LEDs for Rapier 48 and 48i Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 158
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT on, use the command SHOW SYSTEM. To turn on RPS monitoring using SNMP, set the fanAndPsRpsMonitoringStatus variable to on. Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description.
PAGE 159
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT IP Statistics Displays statistics about IP, such as the number of IP datagrams received. ICMP Statistics Displays statistics about ICMP, such as the number of ICMP datagrams received. Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status. Forwarding Database Displays the Forwarding Database table.
PAGE 160
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Disable Disables the port.
PAGE 161
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6 This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6 Layer 3 Gigabit Ethernet Switch.
PAGE 162
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Device Manager LEDs for Rapier G6 Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 163
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Telnet Connects to the switch's Telnet server. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled.
PAGE 164
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information.
PAGE 165
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-LX/SC, G6F-SX/SC, G6F-SX/MTRJ This section describes AT-View Plus Device Manager menus and operations specific to the Rapier G6F-LX/SC, Rapier G6F-SX/SC and Rapier G6F-SX/MT-RJ Layer 3 Gigabit Ethernet Switches.
PAGE 166
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Rapier G6F-SX/SC Rapier G6F-SX/MT-RJ PN 613-50507-00 Rev C Page 166 of 224
PAGE 167
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Device Manager LEDs for Rapier G6F Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 168
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Connects to the switch's Telnet server WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displays the ARP cache on the switch.
PAGE 169
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status. Error Statistics Displays error statistics. Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port.
PAGE 170
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4004 This section describes AT-View Plus Device Manager menus and operations specific to the SwitchBlade 4004, including the AT-SB4211 Switch Controller, power supply units and fan tray installed in it.
PAGE 171
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Main Window SwitchBlade 4004AC with SB4211 Switch Controller, SB4215 Bandwidth Expander, and Line Cards installed PN 613-50507-00 Rev C Page 171 of 224
PAGE 172
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED Device Manager LEDs for AT-SB4211 Switch Controller State Description PWR Green The PSU is receiving power from its supply circuit. MASTER Orange The card is the master switch controller. Gray The card is a slave switch controller. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 173
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT File List Displays a list of the files in the switch's file system. Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis board, and switch controller and line card boards installed in the device. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
PAGE 174
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port.
PAGE 175
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4008 This section describes AT-View Plus Device Manager menus and operations specific to the SwitchBlade 4008, including the AT-SB4211 Switch Controller, power supply units and fan tray installed in it.
PAGE 176
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade 4008 with SB4211 Switch Controller and Line Cards installed PN 613-50507-00 Rev C Page 176 of 224
PAGE 177
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED Device Manager LEDs for AT-SB4211 Switch Controller State Description PWR Green The PSU is receiving power from its supply circuit. MASTER Orange The card is the master switch controller. Gray The card is a slave switch controller. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 178
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis board, and switch controller and line card boards installed in the device. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server.
PAGE 179
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 180
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT SwitchBlade Line Cards This section describes the SwitchBlade Line Cards in AT-View Plus Device Manager. If the following Line Cards are installed in a SwitchBlade chassis, they are displayed in the main window. The operations available for the SwitchBlade include any of these line cards.
PAGE 181
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-SB4411 8-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-SB4412 24-Port (RJ-45) 10BASE-T/100BASE-TX/1000BASE-T Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.
PAGE 182
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4452 8-Port (MT-RJ) 1000BASE-SX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex. AT-SB4461 8-Port (SC) 1000BASE-LX Gigabit Ethernet Line Card LED State Description DUPLEX Green The port is operating at full-duplex.
PAGE 183
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9812T This section describes AT-View Plus Device Manager menus and operations specific to the AT9812T, AT-9812TF and AT-9812T-DC Multi-Layer Gigabit Switches.
PAGE 184
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED Device Manager LEDs for AT-9812T, AT-9812TF, and AT-9812T-DC State Description PWR Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex. Orange The port is operating at half duplex.
PAGE 185
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Config File Name Displays the file name of the start-up configuration file. Chassis Temperature Info Displays the actual temperature of the switch and the temperature status. Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled.
PAGE 186
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port.
PAGE 187
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-9816GB This section describes AT-View Plus Device Manager menus and operations specific to the AT9816GB, AT-9816GF and AT-9816GB-DC Multi-Layer Gigabit Switches.
PAGE 188
Allied Telesyn LED PWR RPS DUPLEX AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-9816GB, AT-9816GF, and AT-9816GB-DC State Description Green The switch is receiving power from the main power supply. Red Main power supply is either off or has failed. Green The switch is receiving power from the redundant power supply. Red RPS has failed. Gray RPS is not installed or RPS monitoring is disabled. Green The port is operating at full duplex.
PAGE 189
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP server. Note - The web browser can only contact the device if the device has a valid resource file loaded and set, and the HTTP server and GUI on the device are enabled. Reset Cold Resets the hardware and executes the default configuration file.
PAGE 190
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired. Spanning Tree Info Displays spanning tree parameters such as priority and cost. Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and edit MIB information about the port.
PAGE 191
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF06 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF06 family of media converters.
PAGE 192
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF06 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 193
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter.
PAGE 194
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF12 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF12 family of media converters.
PAGE 195
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF12 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 196
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12.
PAGE 197
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF106 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF106 family of media converters.
PAGE 198
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF106 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 199
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter.
PAGE 200
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-MCF112 Family This section describes AT-View Plus Device Manager menus and operations specific to the ATMCF112 family of media converters.
PAGE 201
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-MCF112 Family LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The backup power supply is installed and power is on. Gray The backup power supply is not installed or it is installed but not powered on. RPS NORM Green TEST The unit is not performing a link test.
PAGE 202
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Management Interface Info Displays basic interface information for the management port including description, type, physical address, speed and operation status. Temperature Info Displays the temperature of the device in celsius. Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channels 7 to 12.
PAGE 203
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade This section describes AT-View Plus Device Manager menus and operations specific to the ATPBC18 chassis.
PAGE 204
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-PBC18 LED State Description PWR Green The main power supply is installed and power is on. Gray The main power supply is not installed or it is installed but not powered on. Green The optional redundant power supply is installed and power is on. Gray The optional redundant power supply is not installed or it is installed but not powered on.
PAGE 205
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Power Info Displays power supply voltage information. Battery Voltage Displays the battery voltage information. Omega Displays Omega management interface information, including time-out and port status (RS232 and 10Base-T). Telnet Starts a Telnet connection to the chassis. Status Menu From the Status Menu, you can view and edit information about PowerBlade Modules installed on the chassis. Options to view all/per module information are displayed.
PAGE 206
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT PowerBlade Modules This section describes the modules supported by AT-View Plus Device Manager. If modules are installed on the PowerBlade chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.
PAGE 207
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB100 Series Media Converter Modules PB101 PB102 PB103/1 PB103/2 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - The Port A Mode parameter for these modules has a fixed value of 'full' and cannot be modified.
PAGE 208
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB200 Series Switch Modules PB201 PB202 PB202/1 PB202/3 PB202/4 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The 10/100Base-TX port is auto-negotiating.
PAGE 209
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB300 Series Media Converter Modules PB301 LED State Description DUP Green The media converter is operating in full-duplex mode. Gray The media converter is operating in half-duplex mode. Green The Missing Link feature is enabled. ML Note - Port A is displayed as an SC connector instead of a VF-45 connector. Note - The Port A Mode parameter for this module has a fixed value of 'full' and cannot be modified.
PAGE 210
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-PB1000 Series Media Converter Modules PB1001/1 PB1001/3 LED State Description LT Green Link Test is enabled SML Green Smart Missing Link is enabled ML Green Missing Link is enabled PB1005G Note - Smart Missing Link is only supported on the AT-PB1005G module. However, the current firmware version allows the Link Test parameter of the AT-PB1001/1 and AT-PB1001/3 modules to be set to 'smart-missing-link'.
PAGE 211
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-RG213 This section describes AT-View Plus Device Manager menus and operations specific to the ATRG213FX and AT-RG213TX Residential Gateways. Topics: • • • • Main Window Agent Menu RTC Menu Port Menu Main Window AT-RG213 LED Device Manager LEDs for AT-RG213FX and AT-RG213TX State Description PWR Green The residential gateway is receiving power. Note - The AT-RG213FX and AT-RG213TX share the same device image.
PAGE 212
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Agent Menu From the Agent menu, you can view the system information for the device, or log into the CLI using Telnet. System Info Displays basic system information, including system name, location, contact and description.
PAGE 213
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Menu From the Port menu, you can view MIB information about the ethernet and voice ports. Interface Info Ethernet Displays information for each ethernet port. Note - The current firmware version returns 'not available' for the following parameters: o o o o o Port Link State Port Type Port Speed Port Duplex Mode Port Autonegotiation State Voice Displays information for each voice port. Information displayed will vary depending on the protocol used : H.
PAGE 214
Allied Telesyn o o o o AT-VIEW PLUS DEVICE MANAGEMENT Port Initial Retransmission Delay Port Maximum Retransmission Delay Port History Time Port Maximum Propagation Delay Note - SIP : The current firmware version returns 'Not Available' for the Port Registration Time parameter.
PAGE 215
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Port Interface Cards This section describes the following Port Interface Cards supported in AT-View Plus Device Manager : • • • • • • • AT-AR020 AT-AR021 AT-AR022 AT-AR023 AT-AR024 AT-AR026 AT-AR027 If one of these PICs is installed in a PIC bay of a Router (AT-AR400 series or AT-AR700 series), or in a Network Service Module (NSM) of a Router or Layer 3 Switch (Rapier series), it is displayed in the PIC bay of the device in the main window.
PAGE 216
Allied Telesyn LED AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR021(S) and AT-AR021(U) State Description B1 and B2 Green For permanent circuits, HDLC packets are being exchanged between the switch or router and another end system device (normally another switch or router) over any of the B channel. For on-demand ISDN, there is a call up over the respective B-channel. No packet/data transmission over B-channel. Gray AT-AR022 Note - There are no LEDs on this PIC.
PAGE 217
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Note - The four physical ports in this PIC are configured and behave as one ETH port from the viewpoint of the software running on the device. AT-AR027 Note - There are no LEDs on this PIC.
PAGE 218
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Network Service Modules This section describes the following Network Service Modules (NSMs) supported in AT-View Plus Device Manager. AT-AR040 4-PIC slot NSM Note - Up to four Port Interface Cards can be installed in the AT-AR040 NSM. Note - There are no LEDs on this NSM.
PAGE 219
Allied Telesyn LED State Data LEDs Orange AT-VIEW PLUS DEVICE MANAGEMENT Device Manager LEDs for AT-AR041 and AT-AR042 Description For permanent circuits, HDLC packets are being exchanged between the switch or router and another TE end system device (normally another switch or router) over the respective B-channel. For on-demand ISDN, there is a call up over the respective B-channel. No packet/data transmission over B-channel.
PAGE 220
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Uplink Modules This section describes the Uplink Modules that can be installed in Layer 2 Switches, Advanced Layer 2 Switches, and Layer 3 Switches. Topics : • • Layer 2 Switches Uplink Modules Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules Layer 2 Switches Uplink Modules If the uplink modules are installed in one of the Layer 2 switches, they are displayed in the uplink bays of the device in the main window.
PAGE 221
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-A16 LED Device Manager LEDs for AT-A16 State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A17 LED Device Manager LEDs for AT-A17 State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A18 LED Device Manager LEDs for AT-A18 State Description DUPLEX Green The port is operating at full-duplex.
PAGE 222
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT LED Device Manager LEDs for AT-A19 State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A16/AT-A17/AT-A19 LED Device Manager LEDs for AT-A16/AT-A17/AT-A19 State Description DUPLEX Green The port is operating at full- duplex. Orange The port is operating at half-duplex. AT-A45/AT-A47/AT-STACKM Note - There are no LEDs on this module.
PAGE 223
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules If the uplink modules are installed in one of the Rapier series or AT-8700XL series switches, they are displayed in the uplink bays of the device in the main window. The operations available for the main device include any of these uplink modules. AT-A35 Note - There are no LEDs on this module.
PAGE 224
Allied Telesyn AT-VIEW PLUS DEVICE MANAGEMENT AT-A41 Device Manager LEDs for AT-A41/MT and AT-A41/SC LED State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex. AT-A42/GBIC LED Device Manager LEDs for AT-A42/GBIC State Description DUPLEX Green The port is operating at full-duplex. Orange The port is operating at half-duplex.