AT-MC102XLPCI 100TX to 100FX(SC) PCI Bus Media Converter Installation Guide 613-001527 Rev.
Copyright © 2012 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc.
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Declaration of Conformity Manufacturer Name: Allied Telesis, Inc. Declares that the product: Media Converter Model Numbers: AT-MC102XLPCI This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Chapter : Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” posted on the Allied Telesis website at alliedtelesis.com.
Contents Preface ............................................................................................................................................................ 11 Document Conventions .................................................................................................................................... 12 Contacting Allied Telesis ..................................................................................................................................
Contents 6
Figures Figure 1. AT-MC102XLPCI Media Converter ..................................................................................................................... Figure 2. Status LEDs ........................................................................................................................................................ Figure 3. PC Board Location of Jumper J4.........................................................................................................................
List of Figures 8
Tables Table 1. LED Functions ......................................................................................................................................................17 Table 2. Auto-Negotiation Configuration- Jumper J4 Positions ..........................................................................................20 Table 3. MissingLink & Link Test - Jumper J5 Positions ....................................................................................................22 Table 4.
Tables 10
Preface This guide contains instructions on how to install an AT-MC102XLPCI 100Mbps Media Converter.
Preface Safety Symbols This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Warning Warnings inform you that an eye and skin hazard exists due to the presence of a Class 1 laser device.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support.
Preface 14
Chapter 1 Product Overview The AT-MC102XLPCI 100Mbps Media Converter is designed to connect a copper Ethernet medium with a fiber Ethernet medium while being installed in the PCI bus of a computer. A common application for this product is providing an interconnection between a computer's network copper port and a fiber network infrastructure.
Chapter 1: Product Overview Key Features The AT-MC102XLPCI Media Converter features a 100Base-TX twistedpair port and an 100Base-FX fiber optic port. The twisted-pair port has an RJ-45 connector and a maximum operating distance of 100 meters (328 feet). The fiber optic port has a dual SC connector and a maximum operating distance of 2 kilometers (1.2 miles). This media converter operates at 100 Mbps and is configured from the factory for Auto-Negotiation mode.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Status LEDs The AT-MC102XLPCI 100Mbps Media Converter has two status LEDs associated with the 100Base-TX twisted-pair port and the 100Base-FX fiber optic port. The location of these LEDs is shown in Figure 2. Fiber Link LED TX Link LED Figure 2. Status LEDs The functional description of the 100Base-TX twisted-pair port Status LEDs are given in Table 1. Table 1.
Chapter 1: Product Overview Auto MDI/MDIX An RJ-45 twisted-pair port on an 100 Mbps Ethernet network device can have one of two possible wiring configurations: MDI or MDI-X. The RJ-45 port on a PC, router, or bridge is typically wired as MDI, while the twistedpair port on a switch or hub is usually MDI-X. The AT-MC102XLPCI Media Converter features automatic MDI/MDI-X.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Auto-Negotiation The Auto-Negotiation feature is used to automatically determine a common duplex mode between the twisted-pair port and its link partner. This feature is enabled at the factory and is compatible with the IEEE 802.3u specification. The 100FX port usually operates in Full Duplex mode.
Chapter 1: Product Overview Note Although is not marked on J4, Pin 2 is positioned between pins 1 and 3. Table 2.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide MissingLink & Link Test Features The MissingLink & Link Test jumper (J5) on the PC board is configured at the factory with the MissingLink feature enabled and Link Test disabled.
Chapter 1: Product Overview Configuring MissingLink & Link Test Features The MissingLink & Link Test jumper (J5) on the AT-MC102XLPCI assembly is configured at the factory with the MissingLink feature enabled. By reconfiguring this jumper, the link Test function can be enabled (and MissingLink disabled). The location of the jumper is shown in Figure 4. Figure 4. PC Board Location of Jumper J5 The MissingLink & Link Test configuration and jumper (J5) pin positions are given in Table 3.
Chapter 2 Installation This chapter contains the following installation procedures for the AT-MC102XLPCI 100Mbps Media Converter.
Chapter 2: Installation Reviewing Safety Precautions Please review the following safety guidelines before installing the media converter. Note The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements. Warning: Class 1 Laser product. L1 Warning: Do not stare into the laser beam. L2 Warning: Do not look directly at the fiber optic cable ends or inspect the cable ends with an optical lens.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Pre-Installation Checklist This is a pre-installation checklist for you to follow prior to installing the ATMC102XLPCI media converter in your computer chassis: Planning the Installation Unpacking the Media Converter ❒ Planning the Installation ❒ Unpacking the Media Converter ❒ Replacing the Bracket on page 27 ❒ Configuring Auto-Negotiation on page 28 ❒ Configuring MissingLink & Link Test on page 28 Observe the following guidelines when
Chapter 2: Installation Note Store the packaging material in a safe location. If you need to return the unit to Allied Telesis, you may re-use the packing material. 2. Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesis sales. Table 4. AT-MC102XLPCI 100Mbps Media Converter Items Component Description One AT-MC102XLPCI 100Mbps Media Converter with factory-installed low profile bracket One standard profile PCI bracket 3.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Replacing the Bracket The AT-MC102XLPCI Media Converter is shipped with the low-profile bracket attached to the adapter and a separate standard-profile bracket. You may need to replace the low-profile bracket attached to your adapter with the standard profile bracket depending on your PC. The following procedure describes how to remove the low-profile bracket from the adapter and replace it with the standard bracket.
Chapter 2: Installation Configuring Auto-Negotiation A jumper (J4) is pre-installed at the factory between pins 1 and 2 which enables the Auto-Negotiation feature. Refer to Figure 4 for the location of this jumper. If you choose to move this jumper to reconfigure the Auto-Negotiation feature, it must be done prior to the installation of the AT-MC102XLPCI assembly into your computer chassis. Refer to Table 2 on page 20 for a functional description if this jumper (J4).
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Installing a Network Adapter Card The following instructions apply to installing AT-MC102XLPCI Media Converter in most systems. For details about performing these tasks on your particular system, refer to the manuals that were supplied with your computer system. Note To perform this procedure, you need to provide a Phillips-head screw driver. To install an AT-MC102XLPCI Media Converter perform the following procedure: 1.
Chapter 2: Installation 6. Select an empty, non-shared PCI slot and remove the faceplate. See Figure 8. Figure 8. Removing the Faceplate From PCI Slot Note Keep the faceplate in a safe place. You may need it for future use. 7. On the inside of the computer chassis, push the media converter card until it is firmly seated in the appropriate PCI slot by applying even pressure at both corners of the card. See Figure 9. Make sure the card is securely seated. Figure 9.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide 8. Secure the network adapter card to the chassis with a Phillips-head screw (not provided). See Figure 10. Figure 10. Securing the Adapter with a High-profile Bracket 9. Replace the system’s cover and secure it with the screws removed in Step 5. 10. Disconnect any personal antistatic devices. 11. Power the system on.
Chapter 2: Installation Connecting the Network Cables The AT-MC102XLPCI Media Converter has an SC type fiber optic connector with a transmit and receive ports and one twisted-pair connector. See Appendix A, “Fiber Optic Port Specifications” on page 39 for the fiber optic cable specifications. For the AT-MC102XLPCI Media Converter, you need a twisted-pair cable. For cable specifications and pinout information, see Appendix A, “RJ-45 Twisted-Pair Port Specifications” on page 38.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Note The TX port of the AT-MC102XLPCI should be connected to the RX port of the link partner. Similarly, the RX port of the AT-MC102XLPCI should be connected to the TX port of the link partner. 3. On the AT-MC102XLPCI Media Converter, connect the twisted-pair Ethernet cable to the RJ-45 port. See Figure 12. Figure 12. Connecting the Twisted-pair Cable to the AT-MC102XLPCI Media Converter 4.
Chapter 2: Installation 34
Chapter 3 Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. Twisted-Pair LED If the LINK LED for the twisted-pair port is OFF, do the following: 1. Verify that the PC is powered ON and has booted up successfully. 2. Check that the end-node connected to the port is powered ON and is operating properly. 3. Check that the twisted-pair cable is securely connected to the twistedpair port on the media converter and on the remote end-node. 4.
Overview 6. Test the attenuation on the fiber optic cable to ensure that it does not exceed acceptable values. Refer to “RJ-45 Twisted-Pair Port Specifications” on page 38 for more information. 7. Verify that you are using the appropriate type of fiber optic cable and that you have not exceeded the maximum operating distance. For maximum operating distances and cable types, refer to “Fiber Optic Port Specifications” on page 39. 8. Check that the operating specifications (e.g.
Appendix A Technical Specifications Physical Dimensions (W x H): 12.5 cm x 6.4 cm (4.9 in x 2.5 in) Weight: .062 kg (2.2 oz) Temperature Operating Temperature: 0° C to 40° C (32° F to 105° F) Storage Temperature: -20° C to 80° C (-4° F to 176° F) Operating Humidity: 5% to 90% non-condensing Storage Humidity: 5% to 95% non-condensing Operating Altitude: Up to 3,048 meters (10,000 feet) Electrical Rating Input Supply Voltage: 3.3 V DC Power Consumption: 1.
Chapter : Technical Specifications Immunity: EN55024 Electrical Safety: UL 60950-1 (CULUS) EN60950-1 (TUV) CE Laser Safety: EN60825-1 Environmental Compliance Eu-RoHS compliant: Yes China-RoHS compliant: Yes WEEE: Yes RJ-45 Twisted-Pair Port Specifications Cable Requirements The cable requirements of the RJ-45 twisted-pair port are given in Table 5. Table 5.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide RJ-45 TwistedPair Port Pinouts Figure 13 illustrates the pin layout to an RJ-45 connector and port. Figure 13. RJ-45 Connector and Port Pin Layout Table 6 lists the MDI and MDI-X RJ-45 pin signals with a twisted-pair port. Table 6. RJ-45 Pin Signals for MDI and MDI-X Pin MDI Signal MDI-X Signal 1 TX+ RX+ 2 TX- RX- 3 RX+ TX+ 6 RX- TX- Fiber Optic Port Specifications The cable requirements of the fiber port are given in Table 7.
Chapter : Technical Specifications Table 8. Fiber Optic Launch Power Fiber Type 1 MMF Fiber Optic Diameter (microns) 50/125 or 62.5/125 Launch Power (dBm)2 Optical Wavelength 1310 nm Min. Avg. Max. -19.0 -16.8 -14.0 1. MMF = Multimode Fiber 2. The launch power is measured at one meter from the transmitter. Table 9. Fiber Optic Receive Power Fiber Type 1 MMF Fiber Optic Diameter (microns) 50/125 or 62.5/125 Optical Wavelengt h 1310 nm Receive Power (dBm) Min. Typical Saturation -31.
AT-MC102XLPCI 100Mbps Media Converter Installation Guide Table 11. Fiber Optic Loss Specifications Fiber Type1 MMF Fiber Optic Diameter (microns) Optical Wavelength Typical Loss Factor (dB/km) 50/125 1310 nm 1.00 400 62.5/125 1310 nm 1.00 500 Bandwidth (Mhz * km) 1.
Chapter : Technical Specifications 42
