AT-MC1004 AT-MC1005/1 AT-MC1005/2 AT-MC1005/3 AT-MC1005/4 Gigabit Ethernet Media Converters Installation Guide PN 613-50438-00 Rev A
Copyright 2003 Allied Telesyn, Inc. 960 Stewart Drive, Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Statement Standards: This product meets the following standards U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Statement Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. RFI Emission EN55022 Class B 1 Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Table of Contents Electrical Safety and Emission Compliance Statement .......................iii Table of Contents ............................................................................................ v Preface ............................................................................................................. vii Where to Find Web-based Guides ................................................................... vii Document Conventions .......................................................
Table of Contents Chapter 2 Installing the Media Converter ................................................................... 9 Verifying the Package Contents ........................................................................ 9 Planning the Installation............................................................................ 9 Selecting a Site .......................................................................................... 10 Reviewing Safety Guidelines .................................
Preface This guide contains instructions on how to install the AT-MC1004 and the AT-MC1005/x Series Gigabit Ethernet Media Converters. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products. All web-based documents relating to this product and other Allied Telesyn products, can be downloaded from the web site in PDF format.
Preface Contacting Allied Telesyn Technical Support You can contact Allied Teleysn technical support online or by telephone or e-mail. Online Support You can request technical support online accessing the Knowledge Base at http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
AT-MC1004 and AT-MC1005/x Series Installation Guide Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
Chapter 1 Overview The AT-MC1004 and AT-MC1005/x Series Gigabit Ethernet Media Converters are designed to extend the distance of your network by converting Gigabit Ethernet data between twisted pair cabling and either multimode or singlemode fiber optic cabling. The AT-MC1004 media converter features a 1000Base-SX fiber optic port and a 1000Base-T twisted pair port. The fiber optic port has an SC connector and a maximum operating distance of 550 meters (1,804 feet).
Overview Figure 2 shows an example of an AT-MC1005/x Series Media Converter. TX SM 1000Base-LX RX 1000Base-T V2 ML PWR LNK SML LNK ACT LT ACT MODE CLASS 1 LASER PRODUCT DO NOT STARE INTO BEAM AT-MC1005/3 GIGABIT ETHERNET MEDIA CONVERTER Figure 2 AT-MC1005/x Series Gigabit Ethernet Media Converter (Model AT-MC1005/3) Table 1 lists the cabling distances for the Gigabit Ethernet media converters.
AT-MC1004 and AT-MC1005/x Series Installation Guide Key Features The media converters have the following key features: ❑ LEDs for unit and port status ❑ 1000Base twisted pair port with a maximum operating distance of 100 meters (328 feet) ❑ 1000Base fiber optic port with a maximum operating distance of 550 meters (1,804 feet) to 70 kilometers (43.
Overview Fiber Optic Port The 1000Base-SX port on the AT-MC1004 media converter has an SC connector and is designed to operate with multimode fiber optic cabling. This port has a maximum operating distance of 550 meters (1,804 feet) using 62.5/ 125 micron multimode fiber optic cable. The 1000Base-LX port on the AT-MC1005/x Series Media Converters has an SC connector and is designed to operate with single-mode fiber optic cabling. This port has a maximum operating distance of 10 kilometers (6.
AT-MC1004 and AT-MC1005/x Series Installation Guide For example, if the network twisted pair cable to the 1000Base-T port on the media converter were to fail, the unit would respond by dropping the link on the fiber optic port. In this way, the media converter notifies the end-node connected to the fiber optic port that the connection on the twisted pair port has been lost. If the failure had started with the fiber optic cabling, the unit would drop the link to the twisted pair port.
Overview Half- and Full-Duplex Mode Duplex mode refers to the way an end-node sends and receives data on the network. An end-node can operate in either half- or full-duplex mode, depending on its capabilities. An end-node that is operating in half-duplex mode can either send data or receive data, but it cannot do both at the same time. An end-node that is operating in full-duplex mode can send and receive data simultaneously.
AT-MC1004 and AT-MC1005/x Series Installation Guide Network Topologies The AT-MC1004 and AT-MC1005/x Series Gigabit Ethernet Media Converters can be used in two different network topologies: standalone and back-to-back. These network topologies are described below. Standalone Topology A standalone topology uses only one media converter between the end-nodes. Figure 4 illustrates a standalone topology that uses two AT-MC1005/1 media converters to interconnect three remote campuses.
Overview Back-to-Back Topology In some network configurations you may want to interconnect two media converters in what is referred to as a back-to-back topology. In this topology, the media converters not only extend the distance of your network but also convert the fiber optic cable from twisted pair to fiber optic and back again. Figure 5 illustrates one AT-8216FXL/MT switch with an AT-A14 expansion module at each campus. The switches are interconnected by two AT-MC1005/3 media converters.
Chapter 2 Installing the Media Converter Verifying the Package Contents Make sure the following items are included in your media converter package. If any item is missing or damaged, contact your Allied Telesyn sales representative.
Installing the Media Converter Table 3 Twisted Pair Cabling Specifications Model Cable Maximum Operating Distance All Models Shielded Twisted Pair Category 5 or better 100 m (328 ft) Note The 1000Base-T ports use 4 pair (8 wires) in a twisted pair cable. Table 4 Fiber Optic Cabling Specifications Model Cable Maximum Operating Distance Maximum Allowable Loss Budget AT-MC1004 50/125 micron multimode 550 m (1,804 ft) 8.5 dB at 850 nm 62.5/125 micron multimode 1 275 m (902 ft) 7.
AT-MC1004 and AT-MC1005/x Series Installation Guide Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the media converter. Warning Class 1 laser device. 6 Warning Do not stare into the laser beam. 7 Warning Electric Shock Hazard: To prevent electric shock, do not remove the cover. There are no user-serviceable parts inside. The unit contains hazardous voltages and should only be opened by a trained and qualified technician.
Installing the Media Converter Installing the Media Converter The following procedure explains how to install the media converter in your network. Note When two media converters are connected back-to-back with no twisted pair cables connected, the LNK LEDs on the fiber port may flash. This is normal and will not affect the normal operation of the units. Refer to Figure 5 on page 8 for an example of a back-to-back topology. To install the unit, perform the following procedure: 1.
AT-MC1004 and AT-MC1005/x Series Installation Guide 5. Plug the AC/DC power adapter into an appropriate AC power outlet and insert the power plug into the DC receptacle located on the back of the unit. This step does not apply if you installed the unit in an AT-MCR12 chassis. Power Plug DC Receptacle 12 V D C Back of Media Converter AC/DC Power Adapter Figure 7 DC Connector 6. Verify that the PWR LED is green. If the LED is OFF, refer to “Troubleshooting” on page 15 for instructions. 7.
Installing the Media Converter Warranty Registration When you finish installing the product, you should register your product by completing the enclosed warranty card and sending it in.
Chapter 3 Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. If the PWR LED is OFF, do the following: ❑ If the media converter is installed on a desktop, check to be sure that the power adapter is securely connected to a power outlet and that the power adapter cable is securely connected to the back of the media converter. ❑ If the media converter is installed in an AT-MCR12 chassis, check that the unit is fully seated in the slot.
Troubleshooting If the LNK LED for the fiber optic port is OFF, do the following: ❑ Verify that the end-node connected to the port is ON and is operating properly. ❑ Check that the fiber optic cable is securely connected to the fiber optic port on the media converter and on the remote end-node. ❑ Check to be sure that the end-node connected to the port is operating at 1000 Mbps. ❑ Make sure that the fiber optic port on the remote end-node is operating in full-duplex.
Appendix A Technical Specifications Physical Dimensions: WxDxH 10.5 cm x 9.5 cm x 2.5 cm (4.125 in x 3.75 in x 1.0 in) Weight: 294 g (10.
Technical Specifications Fiber Optic Port Specifications Table 5 and Table 6 list the specifications for the fiber optic port. Table 5 Fiber Optic Port Specifications Model Cable Transmitter Output Power (dBm) Optical Wavelength (nm) Minimum Receiver Sensitivity (dBm) AT-MC1004 50/125 or 62.5/125 micron multimode -4.0 to -9.5 850 -17.0 AT-MC1005/1 9/125 micron single-mode -3.0 to -9.0 1310 -20.0 AT-MC1005/2 9/125 micron single-mode -4.0 to 1.0 1310 -21.
AT-MC1004 and AT-MC1005/x Series Installation Guide RJ-45 Pin Assignments Figure 8 shows the pin assignments of the media converter’s RJ-45 port. Pin 1 Pin 8 Figure 8 RJ-45 Pin Assignments Table 7 lists the RJ-45 connector pins and their signals for 1000Base-T.
Appendix B Translated Safety Statements Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety Statements Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacture Name: Allied Telesyn, Inc.
AT-MC1004 and AT-MC1005/x Series Installation Guide 1 RFI Emission 2 Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 3 Immunity EN55024 4 Electrical Safety EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Class B Safety 6 Warning: Class 1 Laser product. 7 Warning: Do not stare into the laser beam.
Translated Safety Statements Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung 2 Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. 3 Störsicherheit 4 Elektrische Sicherheit EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Klasse B EN55024 Sicherheit 24 6 Warnung: Laserprodukt der Klasse 1. 7 Warnung: Nicht direkt in den Strahl blicken.
AT-MC1004 and AT-MC1005/x Series Installation Guide Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission EN55022 Klasse B 2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. 3 Immunitet EN55024 4 Elektrisk sikkerhed EN60950, UL1950, CSA 950 5 Laser EN60825 Sikkerhed 6 Advarsel: Laserprodukt av klasse 1.
Translated Safety Statements Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie 2 Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. 3 Immuniteit EN55024 4 Electrische Veiligheid EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Klasse B Veiligheid 26 6 Waarshuwing: Klasse-1 laser produkt. 7 Waarchuwing Neit in de straal staren.
AT-MC1004 and AT-MC1005/x Series Installation Guide Normes: ce produit est conforme aux normes de suivantes: 1 Emission d’interférences radioélectriques EN55022 Classe B 2 Mise En Garde: dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. 3 Immunité EN55024 4 Sécurité électrique EN60950, UL1950, CSA 950 5 Laser EN60825 Sécurité 6 Attention: Producit laser di classe 1.
Translated Safety Statements Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä 2 Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. 3 Kestävyys EN55024 4 Sähköturvallisuus EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Luokka B Turvallisuus 28 6 Varoitus: Luokan 1 Lasertuote. 7 Variotus: Älä katso säteeseen.
AT-MC1004 and AT-MC1005/x Series Installation Guide Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B 2 Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. 3 Immunità EN55024 4 Sicurezza elettrica EN60950, UL1950, CSA 950 5 Laser EN60825 Norme Di Sicurezza 6 Avvertenza: Prodotto laser di Classe 1.
Translated Safety Statements Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling 2 Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. 3 Immunitet 4 Elektrisk sikkerhet EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Klasse B EN55024 Sikkerhet 30 6 Advarsel: Laserprodukt av klasse 1. 7 Advarsal: Stirr ikke på strålen.
AT-MC1004 and AT-MC1005/x Series Installation Guide Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de radiofrequência EN55022 Classe B 2 Aviso: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
Translated Safety Statements Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI 2 Advertencia: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. 3 Inmunidad EN55024 4 Seguridad eléctrica EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Clase B Seguridad 32 6 ¡Advertencia! Producto láser Clase 1. 7 ¡Advertencia! No mirat fijamente el haz.
AT-MC1004 and AT-MC1005/x Series Installation Guide Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning 2 Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. 3 Immunitet 4 Elsäkerhet EN60950, UL1950, CSA 950 5 Laser EN60825 EN55022 Klass B EN55024 Säkerhet 6 Varning! Laserprodukt av klass 1. 7 Varning! Laserstrålning när enheten är öppen.
