AT-LMC10SC AT-LMC10ST Ethernet Media Converters Installation Guide PN 613-50451-00 Rev B
Copyright © 2004 Allied Telesyn, Inc. 960 Stewart Drive, Suite B, Sunnyvale, CA 94085, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Manufacturer Address: Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. RFI Emission EN55022 Class B 1 Immunity EN55024 2 Warning: This product requires shielded cables to comply with emission and immunity standards.
AT-LMC10SC and AT-LMC10ST Installation Guide Importante: O Anexo A contém advertências de segurança traduzidas para instalar este equipamento. Quando vir o símbolo , leia a advertência de segurança traduzida no seu idioma no Anexo A. Importante: El Apéndice A contiene mensajes de seguridad traducidos para la instalación de este equipo. Cuando vea el símbolo , vaya al Apéndice A para ver el mensaje de seguridad traducido a su idioma.
Table of Contents Electrical Safety and Emission Compliance............................................iii Table of Contents .......................................................................................... vii Welcome to Allied Telesyn ........................................................................... ix Where to Find Web-based Guides .................................................................... ix Document Conventions ..............................................................
Appendix A Technical Specifications ............................................................................. 17 Physical ............................................................................................................. 17 Environmental .................................................................................................. 17 Electrical Rating ............................................................................................... 17 Agency Certifications...................
Welcome to Allied Telesyn This guide contains instructions on how to install an AT-LMC10SC or an AT-LMC10ST Fast Ethernet Media Converter. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site.
Welcome to Allied Telesyn Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales or corporate information. Online Support You can request technical support online by accessing the Allied Telesyn Knowledge Base from the following web site: http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
Chapter 1 Overview The AT-LMC10 Series Ethernet Media Converters include the following models: ❑ AT-LMC10SC ❑ AT-LMC10ST The AT-LMC10 Series Ethernet Media Converters are designed to extend the distance of your network by interconnecting LAN devices that are physically separated by large distances. These media converters have the functionality to connect any managed/unmanaged 10Mbps switch or hub using standard 10Base-T RJ-45 connections and convert the signal to 10Base-FL fiber.
Overview CLASS 1 LASER PRODUCT DO NOT STARE INTO BEAM TX RX 10Base-FL 10Base-T REC REC PWR LNK LNK MDI MDI-X AT-LMC10ST ETHERNET MEDIA CONVERTER Figure 2 AT-LMC10ST Model Converter - Front Panel Figure 3 displays the rear panel of the AT-LMC10 Series Media Converters. 12 V D C Figure 3 AT-LMC10 Series Converters - Rear Panel Table 1 lists the maximum operating distances for the media converters.
AT-LMC10SC and AT-LMC10ST Installation Guide Key Features The media converters have the following key features: ❑ LEDs for unit and port status ❑ MDI/MDI-X selector switch on RJ-45 port ❑ Automatic half- or full-duplex mode operation with 10Base-T or 10Base-FL fiber optic port ❑ Maximum transmission distance of fiber connection is 2 kilometers at full-duplex mode ❑ External AC/DC power adapter ❑ Standard size for use in an AT-MCR12 chassis Status LEDs Table 2 defines the media converter’s LEDs
Overview Note After using the MDI/MDI-X switch to change between the two settings, you must reset the media converter by powering OFF then powering ON the unit. External AC/DC Power Adapter An external AC/DC power adapter is included with the media converter for standalone operation. The power adapter supplies 12VDC to the media converter. Allied Telesyn supplies an approved safety compliant AC power adapter for the 120 or 240V AC versions with an unregulated output of 12VDC at 1 A.
AT-LMC10SC and AT-LMC10ST Installation Guide Network Topologies The AT-LMC10 Series Media Converters can be used in two different types of topologies: standalone and back-to-back. Both topologies are described below. Standalone Topology Figure 4 illustrates a standalone topology where two AT-8224XL switches have been interconnected with an AT-LMC10SC media converter.
Back-to-Back Topology Figure 5 illustrates two media converters in a back-to-back configuration. AT-8224XL AT-LMC10SC PORT ACTIVITY RS-232 TERMINAL PORT STATUS 10BASE-T / 100BASE-TX CLASS 1 LASER PRODUCT DO NOT STARE INTO BEAM TX 10BASE-T / 100BASE-TX SWITCH FAST ETHERNET RX 10Base-FL 10Base-T REC REC PWR LNK LNK MDI MDI-X AT-LMC10SC ETHERNET MEDIA CONVERTER 100 m (328 ft) 2 km (1.
Chapter 2 Installing the Media Converter Verifying the Package Contents Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.
Installing the Media Converter Table 4 10Base-FL Fiber Optic Port Specifications (Full-duplex) Model Type of Fiber Optic Cable Maximum Operating Distance Maximum Allowable Loss Budget AT-LMC10SC 50/125 micron multi-mode 2 km (1.2 mi) 13 dB at 1310 nm 62.5/125 micron multi-mode 2 km (1.2 mi) 13 dB at 1310 nm and AT-LMC10ST Reviewing Safety Precautions Please review the following safety guidelines before installing the media converter. Class 1 laser product. 6 Do not stare into the laser beam.
AT-LMC10SC and AT-LMC10ST Installation Guide Note Do not remove the dust cover from the fiber optic port until you are ready to connect the fiber optic cable. Dust contamination can adversely impact the operating performance of the port on the media converter. 2. If you are installing the media converter in an AT-MCR12 chassis, refer to the chassis’s installation guide for instructions on how to install the unit, then proceed to Step 5. 3.
Installing the Media Converter DC Receptacle Power Plug 12 V D C AC/DC Power Adapter Back of Media Converter DC Polarity Symbols Figure 7 12VDC Connector on Rear Panel 6. Verify that the PWR LED is green. If the LED is OFF, refer to “Troubleshooting” on page 13. 7. Remove the dust cover from the fiber optic connector and connect the cable to the fiber optic port.
AT-LMC10SC and AT-LMC10ST Installation Guide Warranty Registration When you finish installing the product, you should register your product by completing the enclosed warranty card and sending it in.
Chapter 3 Troubleshooting Troubleshooting Guidelines Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. If the PWR LED is OFF, do the following: ❑ If the unit is installed on a desktop, check to be sure that the power adapter is securely connected to a power outlet and that the power adapter cable is securely connected to the back of the media converter. ❑ If the unit is installed in an AT-MCR12 chassis, check that the unit is fully seated in the slot.
Troubleshooting If the LNK LED for the fiber optic port is OFF, do the following: ❑ Verify that then end-node connected to the port is ON and is operating properly. ❑ Check that the fiber optic cable is securely connected to the fiber optic port on the media converter and on the end-node. ❑ Verify that the end-nodes connected to the media converter are operating at the same speed. Both must be operating at 10 Mbps.
AT-LMC10SC and AT-LMC10ST Installation Guide Loopback Test To check hardware reliability of the media converter, perform the following procedure: 1. Power OFF the media converter by unplugging the power adapter from the wall outlet and from the back of the unit. 2. Connect the RJ-45 twisted pair port to a 10Base port on the end-node and power ON the end-node. 3.
Appendix A Technical Specifications Physical Dimensions: WxDxH 10.5 cm x 9.5 cm x 2.5 cm (4.125 in x 3.75 in x 1.0 in) Weight: 0.27 kg (0.
Technical Specifications Agency Certifications EMI/RFI: FCC Class B, EN55022 Class B, VCCI Class B Electrical Safety: EN60950 (TUV), UL1950 (cULus), CE Compliant Immunity: EN55024, VCCI Class B Fiber Optic Port Specifications Table 5 through Table 7 list the specifications for the 10Base-FL fiber optic port. Table 5 Fiber Optic Transmitter Model AT-LMC10SC and AT-LMC10ST Fiber Type1 Fiber Optic Diameter (microns) Optical Wavelength Launch Power (dBm)2 Max. Avg. Min.
AT-LMC10SC and AT-LMC10ST Installation Guide Table 7 Fiber Optic Datalink Model Fiber Type1 Minimum Power / Link Budget Average Signal Loss Minimum Distance Spec.2 Maximum Distance Spec. AT-LMC10SC and AT-LMC10ST 50/125 MMF 13.00 dB 18.70 dB 0 2 km (1.2 mi) 62.5/125 MMF 16.80 dB 22.50 dB 0 2 km (1.2 mi) 1. MMF = Multimode Fiber 2. The recommended minimum range is stated in all cases where the maximum transmitter output power exceeds the receivers saturation level.
Appendix B Translated Electrical Safety and Emission Information Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Electrical Safety and Emission Information Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Manufacturer Address: Allied Telesyn, Inc.
AT-LMC10SC and AT-LMC10ST Installation Guide 1 RFI Emission EN55022 Class B 2 Immunity EN55024 3 Warning: This product requires shielded cables to comply with emission and immunity standards. If it is used with unshielded cables, the user may be required to take measures to correct the interference problem at their own expense. 4 Electrical Safety EN60950 (TUV), UL1950 (cULus) Safety 5 Laser 6 Warning: Class 1 Laser product. 7 Warning: Do not stare into the Laser beam.
Translated Electrical Safety and Emission Information Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung EN55022 Klasse B 2 Störsicherheit EN55024 3 Achtung: Für dieses Produkt sind abgeschirmte Kabel erforderlich, damit den Richtlinien für Emission und Interferenzschutz entsprochen wird.
AT-LMC10SC and AT-LMC10ST Installation Guide Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemissionEN55022 Klasse B 2 Immunitet 3 Advarsel: Dette produkt skal bruges med afskærmede kabler for at overholde bestemmelserne vedrørende udstråling og støjimmunitet. Hvis det bruges med uafskærmede kabler, kan det blive påkrævet af brugeren at korrigere interferensproblemer for egen regning. 4 Elektrisk sikkerhed.
Translated Electrical Safety and Emission Information Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie EN55022 Klasse B 2 Immuniteit EN55024 3 Waarschuwing: Om te voldoen aan de emissie- en immuniteitsnormen dient dit apparaat te zijn voorzien van afgeschermde kabels. Als het met niet-afgeschermde kabels wordt gebruikt, kan het zijn dat de gebruiker maatregelen moet treffen om interferentieproblemen voor eigen rekening op te lossen.
AT-LMC10SC and AT-LMC10ST Installation Guide Normes: ce produit est conforme aux normes de suivantes. 1 Emission d'interférences radioélectriques EN55022 Classe B 2 Immunité EN55024 3 Avertissement: Il faut utiliser des câbles blindés pour ce produit afin de respecter les normes d’émission et d’immunité.
Translated Electrical Safety and Emission Information Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä EN55022 Luokka B 2 Kestävyys EN55024 3 Varoitus: Tämä tuote vaatii suojattuja kaapeleita toimiakseen emissio- ja häiriönsietostandardien mukaisesti. Jostuotetta käytetään ilman suojattuja kaapeleita, käyttäjä voi joutua korjaamaan häirinnän aiheuttaman ongelman omallakustannuksellaan.
AT-LMC10SC and AT-LMC10ST Installation Guide Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B 2 Immunità EN55024 3 Avvertenza: questo prodotto, se utilizzato con cavi schermati, è conforme alle norme sulle emissioni e sull’immunità. In caso di uso senza cavi schermati, l’utente può dover adottare a proprie spese misure correttive contro le interferenze.
Translated Electrical Safety and Emission Information Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling EN55022 Klasse B 2 Immunitet EN55024 3 Advarsel: Dette produktet må brukes med vernede kabler for å tilfredsstille emisjons- og fritakelsesstandarder. Dersom produktet brukes med uvernede kabler, må brukeren muligens rette forstyrrelsesproblemene for egen regning.
AT-LMC10SC and AT-LMC10ST Installation Guide Padrões: Este produto atende aos seguintes padrões. 1 Emissão De Interferência De Radiofrequência EN55022 Classe B 2 Imunidade EN55024 3 Advertência: Este produto requer a utilização de cabos blindados para cumprimento dos standards de limites de emissão e imunidade. Se o produto for utilizado com cabos não blindados, o utilizador poderá necessitar de tomar medidas para correcção de problemas de interferência, por sua própria conta.
Translated Electrical Safety and Emission Information Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI EN55022 Clase B 2 Inmunidad EN55024 3 Advertencia: Este producto exige cables protectores para ajustarse a las normas de emisión e inmunidad. Si se utiliza con cables sin protección, el usuario tendrá que correr con los gastos por las medidas a tomar en caso de problemas de interferencias.
AT-LMC10SC and AT-LMC10ST Installation Guide Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning EN55022 Klass B 2 Immunitet EN55024 3 Varning! Denna produkt kräver skärmade kablar för att uppfylla standardkraven för emission och immunitet. Om den används med oskärmade kablar kan användaren vara tvungen att vidta åtgärder på egen bekostnad för att åtgärda störningsproblemet.
