AT-FS709FC 10/100 Fast Ethernet Unmanaged Switch Installation Guide PN 613-10817-00 Rev.
Copyright 1999 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086, USA All rights reserved. No part of this publication may be reproduced without prior written permission from AlliedTelesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. AlliedTelesyn International, Corp.
Safety Warnings STANDARDS: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Manufacture Address: Allied Telesyn International, Corp. 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Fast Ethernet Unmanaged Switch Model Number: AT-FS709FC This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Safety Warnings WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. IMPORTANT: Appendix A contains translated safety statements for installing this equipment. Go to Appendix A for the translated safety statement in your language. WICHTIG: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Schlagen Sie in Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
Table of Contents Safety Warnings ................................................................................................................... iii Chapter Product Description ..............................................................................................................1 Overview ..................................................................................................................................1 Description ................................................................
Appendix C Technical Support Fax Order .............................................................................................31 Incident Summary.................................................................................................................31 Appendix D AT-FS709FC Installation Feedback ....................................................................................33 Appendix E Where To Find Us ......................................................................................
Chapter 1 Product Description Overview The AT-FS709FC is a nine port Fast Ethernet switch with eight auto-negotiating 10Base-T/ 100Base-TX shielded twisted pair RJ45 ports and one 100Base-FX(SC) fiber port. The switch features include: ! IEEE 802.3, IEEE 802.3u and IEEE 802.
Product Description Figure 1 shows the switch front panel. TX RX Figure 1 AT-FS709FC Front Panel Description This section includes: ! Connectors ! LEDs ! MDI/MDI-X Port 8 ! Power Supply ! Auto-negotiation Connectors Table 1 lists and defines the type of connectors available and their function.
AT-FS709FC Installation Guide LEDs Figure 2 illustrates the switch front panel LEDs. Table 2 lists and describes these LEDs. Power Link/Act 100M FDX 1 2 3 4 5 6 7 8 9 Figure 2 A Close Up of the Front Panel LEDs Table 2 LED Status LEDs Color LINK/ACTIVITY Green Description On indicates a valid physical link on the port. Blinking indicates data is being transmitted. Off means no link. 100M Green On means the bandwidth is 100 Mbps. Off means the bandwidth is 10 Mbps.
Product Description MDI/MDI-X Port 8 Port 8 is associated with the MDI function. Port 8 gives you the flexibility of using a straight-through cable to connect to a hub or another switch (Port 8 MDI), or to any DTE device (Port 8 MDI-X), such as an end station or a server. Note Use only one Port 8, either Port 8 MDI or Port 8 MDI-X.
Chapter 2 Installation Before you Proceed Before installing the switch, make sure you read “Electrical Safety and Installation Requirements” on page 15. Verifying Package Contents Make sure that the package includes the following items: ! One AT-FS709FC switch ! One AC power cord (for the U.S., Continental Europe, and the U.K.
Installation Site Requirements Make sure you observe the following site requirements: ! Make sure you are placing the switch in a dust-free and moisture-free environment. ! Do not block ventilation openings on the unit. ! Make sure that the switch’s power is accessible and cables can be connected easily. ! Cabling should be away from sources of electrical noise such as radios, transmitters, broadband amplifiers, power lines and fluorescent fixtures. ! Do not place objects on top of the switch.
AT-FS709FC Installation Guide Note Do not plug a phone jack connector into any RJ45 port. This may damage the switch. Use only twisted-pair cables with RJ45 connectors that conform with FCC standards. 6. Attach the data cables and observe normal operation as indicated by the port LEDs. Use only one Port 8, either Port 8 MDI or Port 8 MDI-X. 7. Attach fiber optic cable with SC connectors to Port 9 and observe LEDs for normal operation.
Installation 6. Attach the data cables and observe normal operation as indicated by the port LEDs. Use only one Port 8, either Port 8 MDI or Port 8 MDI-X. For typical configuration information, refer to “Cascade Configuration” on page 9. 7. Attach fiber optic cable with SC connectors to Port 9 and observe LEDs for normal operation. Note Auto-negotiation for transmission mode supports full-duplex only if the connected device also negotiates for full-duplex transmission mode.
AT-FS709FC Installation Guide Cascade Configuration Cascading means that two switches can be connected together using any of the switch ports, provided you maintain the same media type. Two switches can be cascaded to support multiple network port connections. Cable length to the nodes must follow the 100Base-TX cabling specifications. To cascade installed switches, do the following: Note When cascading switches, you must use the same media type from port to port. 1.
Installation Uplink Configuration For 100 Mbps connection to the backbone, use Port 9. Figure5 illustrates how this switch can be used as a full-duplex uplink to the backbone in a typical office complex using Fiber cable.
Chapter 3 Troubleshooting This chapter describes the procedures to test and troubleshoot the switches. Connectivity Testing In the following procedure, you will test each port for a valid connection and to confirm the correct operation of the network. 1. Start with Ports 1 and 2. Connect these two ports of a single switch to two nodes or workstations and turn on the switch power. 2.
Troubleshooting Problem Solving Is the unit receiving power? Check the Power LED on the front of the switch. This green LED should be lit. Note The switch performs a self-diagnostic test upon power on, and takes about 20 seconds to complete. If the Power LED is not on, check both ends of the power cord or adapter. Make sure the power cord or adapter is plugged into a functioning wall outlet and that it is properly inserted into the switch’s connector on the back of the unit.
AT-FS709FC Installation Guide 4. Problem 4: There is data loss between the switch and one of the connected network nodes. ! Solution 4: — Make sure that the distance between the switch and the connected network device is no greater than 100 m (328 ft). — Make sure you are using Category 5 cable.
Appendix A Electrical Safety and Installation Requirements STANDARDS: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Manufacture Address: Allied Telesyn International, Corp.
Electrical Safety and Installation Requirements Canadian Department of Communications This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. RADIATED ENERGY RFI Emission EN55022 Class B WARNING: This product requires shielded cables to comply with Class B emission limits.
AT-FS709FC Installation Guide CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling. OPERATING TEMPERATURE This product is designed for a maximum ambient temperature of 40 degrees C. ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Electrical Safety and Installation Requirements BETRIEBSTEMPERATUR Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 40° C entworfen. ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften entsprechen. STANDARDER: Dette produkt tilfredsstiller de følgende standarder. Radiofrekvens forstyrrelsesemission EN55022 Klasse B ADVARSEL: Der skal bruges skærmkabler med dette produkt for at opfylde Klasse B emissionsgrænser.
AT-FS709FC Installation Guide BETJENINGSTEMPERATUR Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C. ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer. EISEN: Dit product voldoet aan de volgende eisen. RFI Emissie EN55022 Klasse B WAARSCHUWING: Dit product vereist beschermende kabels in overeenstemming met de limieten van Klasse B emissie.
Electrical Safety and Installation Requirements OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht ongehinderd toelaten voor afkoeling. BEDRIJFSTEMPERATUUR De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius. ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften.
AT-FS709FC Installation Guide ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de circuler librement pour le refroidissement. TEMPÉRATURE DE FONCTIONNEMENT Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés Celsius. POUR TOUS PAYS: Installer le matériel conformément aux normes électriques nationales et locales. STANDARDI : Tämä tuote on seuraavien standardien mukainen.
Electrical Safety and Installation Requirements HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi. KÄYTTÖLÄMPÖTILA Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C. KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti. STANDARD: Questo prodotto è conforme ai seguenti standard.
AT-FS709FC Installation Guide ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero ricircolo dell’aria ambiente per il raffreddamento. TEMPERATURA DI FUNZIONAMENTO Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi centigradi. TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche nazionali. SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
Electrical Safety and Installation Requirements DRIFTSTEMPERATUR Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius. ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder. PADRÕES: Este produto atende aos seguintes padrões. Emissão de interferência de radiofrequência EN55022 Classe B AVISO: Este produto requer cabos protegidos a fim de obedecer aos limites de emissão da Classe B.
AT-FS709FC Installation Guide CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso livre ao ar ambiente para arrefecimento adequado do aparelho. TEMPERATURA DE FUNCIONAMENTO Este produto foi projetado para uma temperatura ambiente máxima de 40 graus centígrados. TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para instalações elétricas. ESTÁNDARES: Este producto cumple con los siguientes estándares.
Electrical Safety and Installation Requirements ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso libre al aire ambiental de la sala para su enfriamiento. TEMPERATURA REQUERIDA PARA LA OPERACIÓN Este producto está diseñado para una temperatura ambiental máxima de 40 grados C. PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos locales y nacionales. STANDARDER: Denna produkt uppfyller följande standarder.
AT-FS709FC Installation Guide DRIFTSTEMPERATUR Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader Celsius. ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser för elektrisk utrustning.
Appendix B Switch Specifications Physical Characteristics Chassis dimensions: LxWxH 13 in x 8.0 in x 1.72 in 330 mm x 203 mm x 44 mm Weight: 4 lbs (2.0 kg) Operating temperatures: 0° to 40° C (32° to 104° F) Storage temperatures: -20° to 60° C (-40° to 158° F) Relative humidity: 10% to 80% (operating) 5% to 95% (storage) Operating altitude: Up to 10,000 ft (3,048 m) Safety Agency CE compliant Standard: IEEE 802.3 10Base-T Ethernet IEEE 802.3u, 100Base-TX Fast Ethernet, IEEE 802.
Switch Specifications Cable Specifications Table 4 IEEE 802.3 and 802.3u Network Specifications 10Base-T 100Base-TX Media Shielded Twisted Pair Category 3 or 5 Shielded Twisted Pair Category 5 only Topology Star, Tree Star, Tree External Devices Network Adapter Card, Repeater, Switch Network Adapter Card, Repeater, Switch Maximum Segment Length 328 ft (100 m) 328 ft (100 m) Table 5 100Base-FC Media SC Fiber Optic Cable 50/100 µm, or 62.
Appendix C Technical Support Fax Order Name ___________________________________________________________________ Company ________________________________________________________________ Address _________________________________________________________________ City ________________________State/Province ________________________________ Zip/Postal Code ___________________ Country_________________________________ Phone _______________________________Fax_________________________________ Incident Summary Model
Appendix D AT-FS709FC Installation Feedback Please tell us what additional information you would like to see discussed in the guide. If there are topics you would like information on that were not covered in the guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of the guide.
Appendix E Where To Find Us For Technical Support or Service Location Phone Fax Americas United States, Canada, Mexico, Central America, South America 1 (800) 428-4835 1 (918) 628-3222 Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India (+65) 3815-613 (+65) 3833-830 Australia Australia, New Zealand (+61) 2-943-5111 (+61) 2-9438-4966 France France, Belgium, Luxembourg, The Netherlands, Middle East, Africa (+33) 1-60-92-15-32 (+33) 1-69-28-37-49 Germany Germ
