AT-FS708LE 10/100Base Ethernet Switch Installation Guide PN 613-50181-00 Rev A
Copyright 2001 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
Electrical Safety and Emission Statement Standards: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Ethernet switch Model Number: AT-FS708LE This product complies with FCC Part 15, Class B Limits: This device complies with part 15 of the FCC Rules.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når De ser symbolet , skal De slå op i tillæg A og finde de oversatte sikkerhedsadvarsler i Deres eget sprog. Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze ziet, raadpleeg Appendix A apparatuur. Wanneer u de voor vertaalde veiligheidsinstructies in uw taal.
Table of Contents Electrical Safety and Emission Statement........................................................ iii Table of Contents ......................................... vii Welcome to Allied Telesyn .......................... ix Where to Find Web-based Guides ................... ix Document Conventions .................................... ix Contacting Allied Telesyn ................................. x Online Support ........................................... x Telephone or Fax Support .........
Installing the Unit........................................... 10 Verifying the Package Contents .............. 10 Selecting a Site ......................................... 11 Reviewing Safety Guidelines ................... 12 Installing the Unit on a Desktop ............. 14 Installing the Unit on a Wall................... 15 Verifying and Troubleshooting the Installation....................................................... 17 Warranty Registration ....................................
Welcome to Allied Telesyn This guide contains instructions on how to install an Allied Telesyn AT-FS708LE Ethernet Switch. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com contains the most recent documentation for all Allied Telesyn products. All documents can be downloaded from the web site in PDF format. Document Conventions This guide uses several conventions that you should become familiar with before you begin to install the product.
Caution A caution indicates that performing or omitting a specific action may result in equipment damage or loss of data. Warning A warning indicates that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn You can contact Allied Telesyn technical support by telephone, fax, e-mail, or online. Online Support You can request technical support online by filling out the Online Technical Support Form at www.alliedtelesyn.com/forms/ support.htm.
AT-FS708LE Installation Guide Telephone or Fax Support For technical support via fax, please fill out the“Technical Support Fax Order” on page 35 and send it to the appropriate location listed below.
E-mail Support United States and Canada TS1@alliedtelesyn.com Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands latin_america@alliedtelesyn.com United Kingdom, Sweden, Norway, Denmark, and Finland support_europe@alliedtelesyn.com Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
AT-FS708LE Installation Guide Latin America, the Caribbean, Virgin Islands Tel: international code + 425-481-3852 Fax: international code + 425-483-9458 Mexico and Puerto Rico Tel: 1-800-424-5012, ext 3852 or 1-800-424-4284, ext 385 2 Mexico only: 95-800-424-5012, ext 3852 Fax: international code + 425-489-9191 FTP Server If you need a new version of management software for an Allied Telesyn device and you know the file name of the program, you can download the software by connecting directly to our FTP s
For Sales or Corporate Information For sales or corporate information, contact Allied Telesyn at one of the following locations: Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191 Allied Telesyn International, Corp.
AT-FS708LE Fast Ethernet Switch Overview The AT-FS708LE unit is a 10Base-T/100BaseTX Ethernet switch. The unit provides you with a simple, cost-effective solution for Ethernet switching between end nodes operating at either 10 or 100 Mbps.
Features The AT-FS708LE Ethernet Switch has the following features: ❑ Eight auto-negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ One Uplink port for connecting the AT-FS708LE unit to a switch or hub without a crossover cable ❑ IEEE 802.3 and IEEE 802.3u compliant ❑ 256K of buffer memory ❑ Store-and-forward packet forwarding design ❑ Total bandwidth of up to 800 Mbps ❑ MAC address table capacity of 8,000 entries ❑ IEEE 802.
AT-FS708LE Installation Guide Figure 2 and Figure 3 show the front and back panels of the switch.
Physical Description The physical description for the switch includes: ❑ Ports 1 through 7 ❑ Port 8 and the Uplink port ❑ LEDs ❑ Power supply Ports 1 Through 7 Ports 1 through 7 can operate at either 10 Mbps or 100 speed and in either full- or half-duplex mode. The ports, featuring RJ-45 connectors, are configured as MDI-X, meaning that you can connect a workstation or server to one of the ports without using a crossover cable.
AT-FS708LE Installation Guide Port 8 and the Uplink Port Port 8 and the Uplink port allow you to connect an additional workstation to the unit or interconnect the unit with a switch, hub, or router, without the use of a crossover cable. If you need to connect an additional workstation to the unit, use Port 8, which is configured as MDI-X, just like ports 1 through 7. If you need to connect the unit to an Ethernet switch, hub, or router, use the Uplink port, which is configured as MDI.
Front Panel LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description Power Green On means the switch is receiving power. Off means the switch is not receiving power. 100M Green On means the port is operating at 100 Mbps. Yellow On means the port is operating at 10 Mbps. Green On indicates a valid physical link on the port. Flashing indicates data is being transmitted or received on the port. Off means there is no link on the port.
AT-FS708LE Installation Guide Table 1 LED Functions (continued) LEDs Color Description Fdx/Hdx Green On indicates the port is operating in full-duplex mode. Off indicates the port is operating in half-duplex mode. Power Supply The AT-FS708LE Ethernet Switch uses an external power adapter that comes standard with the unit.
Network Topologies Figure 4 illustrates a network that consists of one AT-FS708LE Ethernet Switch used to interconnect seven workstations and a server. The Uplink port is not used in this configuration.
AT-FS708LE Installation Guide Figure 5 illustrates a network of two ATFS708LE Ethernet Switches that have been interconnected using the Uplink port on the top unit. Using the Uplink port eliminates the need for a crossover cable to interconnect the devices.
Installing the Unit This section contains the procedures for installing the unit. Verifying the Package Contents Make sure that the package includes the following items. If any item is damaged or missing, contact your Allied Telesyn representative for assistance.
AT-FS708LE Installation Guide Selecting a Site Be sure to observe the following site requirements: ❑ Make sure you are placing the device in a dust-free and moisture-free environment. ❑ Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the front and back of the unit for ventilation. ❑ Make sure that the unit’s power is accessible and cables can be connected easily.
❑ Observe the following cabling specifications: Ports Connector Type 1 to 8 RJ-45 Type of Cable Maximum Distance Category 3, 4, or 5 (10 Mbps) 100 m (328 ft) Category 5 (100 Mbps) Uplink RJ-45 Category 3, 4, or 5 (10 Mbps) 100 m (328 ft) Category 5 (100 Mbps) Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the device. Warning Power cord is used as a disconnection device: To deenergize equipment, disconnect the power cord.
AT-FS708LE Installation Guide Caution Pluggable Equipment: The socket outlet should be installed near the equipment and should be easily accessible. 6 Caution Air vents: The air vents on the unit must not be blocked and must have free access to the room ambient air for cooling. 7 Caution Operating Temperature: This product is designed for a maximum ambient temperature of 40°C. 8 Caution All Countries: Install this product in accordance with local and National Electric Codes.
Installing the Unit on a Desktop To install the switch on the desktop, perform the following procedure. To mount the unit on a wall, perform the steps “Installing the Unit on a Wall” on page 15. 1. Attach the four self-adhesive rubber feet to the bottom of the device, positioning them in the indentations. 2. Place the device on a flat, level surface. 3. Plug the power adapter into a power source and then plug the DC power cord into the DC connector on the front panel of the switch.
AT-FS708LE Installation Guide 5. Attach the data cables to the ports on the hub. Do not use crossover cables to connect workstations or servers to ports 1 through 8. Do not use a crossover cable to connect a switch, hub, or router to the Uplink port. Note You can use either port 8 or the Uplink port on an AT-FS708LE device. You cannot use both ports simultaneously. 6. Go to the procedure “Verifying and Troubleshooting the Installation” on page 17.
Note For wall-mount installation, you must supply the two screws and plastic anchors or other material necessary to physically mount the switch to the wall. 3. Install two plastic anchors and two pan-head screws into the wall, separated by 5 centimeters (approximately 2 inches). 4. Position the device onto the wall screws. 5. Plug the power adapter into a power source and plug the DC power cord into the DC connector on the front panel of the switch. Warning The power cord is used as a disconnection device.
AT-FS708LE Installation Guide 7. Attach the data cables to the switch ports. Do not use crossover cables to connect workstations or servers to ports 1 through 8. Do not use a crossover cable to connect a switch, hub, or router to the Uplink port. Note You can use either port 8 or the Uplink port, but you cannot use both simultaneously. 8. Go to the procedure “Verifying and Troubleshooting the Installation” on page 17.
❑ Check to be sure that the power outlet has power by connecting another device to it. ❑ Try replacing the power adapter with another power adapter. 2. Check the Link/Act LED for each port. The LED should be lit steady or flashing. If a Link/Act LED is OFF, check the following: ❑ Verify that the node connected to the port on the switch is powered ON. If the node is OFF, power the unit ON. ❑ Verify that the distance between the switch and the connected network device is no greater than 100 meters (328 feet).
AT-FS708LE Installation Guide ❑ Verify that you are using the correct type of cable: Category 3, 4, or 5 for 10 Mbps operation and Category 5 cable for 100 Mbps operation. Warranty Registration When you have finished installing the unit, you should register your product by completing the enclosed warranty card and sending it in, or by visiting our web site at www.alliedtelesyn.com/forms/ warranty.htm and completing the on-line registration. Technical Specifications Standards Compatibility: IEEE 802.
Flow Control: Full-duplex: Disable IEEE 803.3u Half-duplex: Enable backpressure Physical Dimensions: WxDxH 146 x 82 x 26 mm (5.75 x 3.23 x 1.02 in.) Environment Specifications: Operating Temperature 0° to 40° C Storage Temperature -25° to 70° C Operating Humidity 5% to 90% Relative Humidity Storage Humidity 10% to 95% Relative Humidity Electromagnetic Emission: FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) Certification: CE Mark Immunity: EN55024 Safety: UL 1950, CSA C22.2 No.
Appendix A Translated Safety and Emission Information Important: This appendix contains multiplelanguage translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idiomas das advertências de segurança neste guia. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.
AT-FS708LE Installation Guide Standards: This product meets the following standards: U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International Manufacture Address: 950 Stewart Drive, Suite B Sunnyvale, CA 94085 USA 408-730-0950 Manufacture Telephone: Declares that the product: Ethernet switch Model Number: AT-FS708LE This product complies with FCC Part 15, Class B Limits: This device complies with part 15 of the FCC Rules.
Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. 24 1 RFI Emissions 2 WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 3 Immunity EN55024 4 Electrical Safety UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide 11 USA/CANADA: Use a UL Listed/CSA Certified AC adapter of DC 9V, 1A. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung 2 WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. 3 Störsicherheit EN55024 4 Elektrische Sicherheit UL 1950, CSA C22.2 No.
26 Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission: FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. 3 Immunitet EN55024 4 Elektrisk sikkerhed UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie 2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. 3 Immuniteit 4 Electrische Veiligheid FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) EN55024 UL 1950, CSA C22.2 No. 950, EN60950 VEILIGHEID 5 WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE ONTKOPPELEN.
28 Normes: ce produit est conforme aux normes de suivantes. 1 Emission d’interférences radioélectriques FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. 3 Immunité EN55024 4 Sécurité électrique UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä 2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. 3 Kestävyys EN55024 4 Sähköturvallisuus UL 1950, CSA C22.2 No.
30 Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. 3 Immunità EN55024 4 Sicurezza elettrica UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling 2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. 3 Immunitet EN55024 4 Elektrisk sikkerhet UL 1950, CSA C22.2 No.
32 Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de radiofrequência FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. 3 Imunidade EN55024 4 Segurança Eléctrica UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI 2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. 3 Inmunidad EN55024 4 Seguridad eléctrica UL 1950, CSA C22.2 No.
34 Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning 2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. 3 Immunitet EN55024 4 Elsäkerhet UL 1950, CSA C22.2 No. 950, EN60950 FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) SÄKERHET 5 VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln. 6 UTRUSTNING MED PLUGG.
Appendix B Technical Support Fax Order Name __________________________________ Company _______________________________ Address ________________________________ City____________________________________ State/Province __________________________ Zip/Postal Code ________________________ Country ________________________________ Phone __________________________________ Fax ___________________________________ Incident Summary Model number of Allied Telesyn product I am using______________________________ Firmwa
Brief summary of problem _______________ _______________________________________ Conditions (List the steps that led up to the problem. _________________________ _______________________________________ _______________________________________ Detailed description (Please use separate sheet) Please also fax printouts of relevant files such as batch files and configuration files. When completed, fax this sheet to the appropriate Allied Telesyn office. Fax numbers can be found on page x.
Appendix C AT-FS708LE Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. You can fax or mail this form to the mailing address and fax number at the bottom of the page.
