AT-FS708LE Fast Ethernet Switch Version 2 Installation Guide PN 613-50636-00 Rev A
Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Statement Standards: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Fast Ethernet Switch Model Number: AT-FS708LE Version 2 This product complies with FCC Part 15, Class B Limits: This device complies with part 15 of the FCC Rules.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AT-FS708LE Installation Guide Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når De ser symbolet , skal De slå op i tillæg A og finde de oversatte sikkerhedsadvarsler i Deres eget sprog. Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de ziet, raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw taal.
Table of Contents Electrical Safety and Emission Statement ....................................3 Welcome to Allied Telesyn .........................9 Where to Find Web-based Guides ..................9 Document Conventions ...................................9 Contacting Allied Telesyn ..............................10 Online Support ........................................10 E-mail and Telephone Support...............11 Returning Products .................................
Cascade Topology ....................................23 Planning the Installation ...............................24 Verifying the Package Contents .............24 Selecting a Site ........................................25 Reviewing Safety Guidelines ..................26 Installing the Unit on a Desktop ...................28 Installing the Unit on a Wall .........................29 Warranty Registration ...................................31 Troubleshooting ..............................................
Welcome to Allied Telesyn This guide contains instructions on how to install an Allied Telesyn AT-FS708LE Fast Ethernet Switch. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site.
Caution Cautions informs you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings informs you that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales or corporate information.
AT-FS708LE Installation Guide E-mail and Telephone Support For Technical Support via E-mail or telephone, refer to the Support & Services section of the Allied Telesyn web site: http://www.alliedtelesyn.com. Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
AT-FS708LE Fast Ethernet Switch Overview The AT-FS708LE unit is a 10Base-T/ 100Base-TX Fast Ethernet Switch. The unit provides you with a simple, cost-effective solution for Ethernet switching between endnodes operating at either 10 or 100 Mbps. Figure 1 and Figure 2 show the front and back panels of the switch.
8x 7x 6x 5x 4x 3x 2x 1x Figure 2 Back Panel Key Features The AT-FS708LE Ethernet Switch has the following features: ❑ LEDs for unit and port status ❑ 8 Auto-Negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ Auto MDI/MDI-X on all ports ❑ IEEE 802.3 and IEEE 802.3u compliant ❑ Store and forward switching mode ❑ MAC address table capacity of up to 4,000 entries ❑ IEEE 802.
AT-FS708LE Installation Guide Status LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description PWR Green Indicates the switch is receiving power. 100M Green Indicates the port is operating at 100 Mbps. OFF Indicates the port is operating at 10 Mbps. Green Indicates a valid physical link on the port. Blinking Indicates data is being transmitted or received on the port. Green Indicates the port is operating in full-duplex mode.
Power Supply The AT-FS708LE Ethernet Switch uses an external power adapter that comes standard with the unit. Store and Forward The AT-FS708LE switch uses store and forward as the method for receiving and transmitting frames. When an Ethernet frame is received on a switch port, the switch does not retransmit the frame out the destination port until it has received the entire frame and stored the frame in a port buffer. It then examines the frame to determine if it is a valid frame.
AT-FS708LE Installation Guide end-node to stop transmitting data to allow the slower end-node to catch up. An example of this would be when a server operating at 100 Mbps is sending data to a workstation operating at only 10 Mbps. How a switch signals an end-node to stop transmitting data differs depending on the speed and duplex mode of the end-node and switch port. A twisted pair port operating at 100 Mbps port and half-duplex mode stops an end-node from transmitting data by forcing a collision.
The AT-FS708LE supports TX Flow Control only. This means a PAUSE packet will be transmitted to the end-node connection if it receives data faster than it can switch the packets. The AT-FS708LE does not support RX Flow Control, however, and it will not respond to PAUSE packets sent to it by an end-node. Twisted Pair Ports The AT-FS708LE switch has eight 10Base-T/ 100Base-TX twisted pair ports. Each twisted pair port features a RJ-45 connector.
AT-FS708LE Installation Guide port on the switch and the end-node are operating at the same speed and that they are communicating at the highest possible common speed of the devices. Duplex Mode Duplex mode refers to the way an end-node sends and receives data on the network. An end-node can operated in either half- or fullduplex mode depending on its capabilities. An end-node that is operating in half-duplex mode can either send data or receive data, but it cannot do both at the same time.
Note Since the AT-FS708LE ports operate in Auto-Negotiate mode only, the end-nodes connected to the AT-FS708LE must also be configured to operate in the AutoNegotiate mode. If an end-node is configured to a specific duplex in a manual mode, it will not respond to the Auto-Negotiate protocol from the AT-FS708LE. (The speed is determined from the link pulses, however, so the speed is always detected correctly.) As a result, the AT-FS708LE port setting will end up at half-duplex.
AT-FS708LE Installation Guide To connect two 10 Mbps or 100 Mbps network devices together that have dissimilar port wiring configurations, such as an MDI to MDI-X, you would use a straight-through twisted pair cable. To connect two networks devices that have the same wiring configuration, such as MDI to MDI, you would use a crossover cable. The AT-FS708LE switch features automatic MDI/MDI-X.
Network Topologies The AT-FS708LE switch can be used in a variety of network topologies, such as a standalone or cascade. Both topologies are described below. Standalone Topology Figure 3 illustrates the standalone topology where each end-node is directly connected directly to a 10/100Base-TX port on an AT-FS708LE switch. This gives each end-node a dedicated 10 Mbps or 100 Mbps link.
AT-FS708LE Installation Guide Cascade Topology Figure 4 illustrates the cascade topology where Port 1 on the AT-FS708LE switch is connected to Port 8 on the AT-FS716E switch. Since Port 1 is wired as auto MDI/MDI-X, a crossover or straight-through Category 5 or better twisted pair cable can be use.
Note Cascading switches, as shown in Figure 4, can result in data loss between switches if the data rate exceeds 100 Mbps. Symptoms may include inability of certain workstations to “Log-On” to a server or unusually slow data transfer rates between workstations or servers. Planning the Installation This section contains the procedures for installing the unit. Verifying the Package Contents Make sure that the package includes the following items.
AT-FS708LE Installation Guide Selecting a Site Be sure to observe the following site requirements: ❑ Make sure you are placing the device in a dust-free and moisture-free environment. ❑ Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the front and back of the unit for ventilation. ❑ Make sure that the unit’s power is accessible and cables can be connected easily.
Table 2 10Base-T/100Base-TX Twisted Pair Port Cabling Specifications Operating Mode Twisted Pair Cable Maximum Operating Distance 10Base-T Shielded or unshielded Category 3 or better 100 m (328 ft) 100Base-TX Shielded or unshielded Category 5 or better 100 m (328 ft) Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the device. Warning Power cord is used as a disconnection device: To deenergize equipment, disconnect the power cord.
AT-FS708LE Installation Guide Caution Pluggable Equipment: The socket outlet should be installed near the equipment and should be easily accessible. 6 Caution Air vents: The air vents on the unit must not be blocked and must have free access to the room ambient air for cooling. 7 Caution Operating Temperature: This product is designed for a maximum ambient temperature of 40°C. 8 Caution All Countries: Install this product in accordance with local and National Electric Codes.
Installing the Unit on a Desktop To wall-mount the switch on a wall, refer to “Installing the Unit on a Wall” on page 29. To install the switch on the desktop, perform the following procedure. 1. Attach the four self-adhesive rubber feet to the bottom of the device, positioning them in the indentations. 2. Place the device on a flat, level surface. Warning The power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. 5 3.
AT-FS708LE Installation Guide 6. Power ON the end-nodes connected to the switch. 7. Check that the LNK/ACT LED for each port on the switch is green. If a LED is OFF, refer to “Troubleshooting” on page 31. The AT-FS708LE switch is now ready for use. Installing the Unit on a Wall For wall-mount installation, you can position the switch vertically or horizontally on the wall using the keyhole cutouts in the bottom of the switch chassis.
4. Position the switch onto the wall screws with the LEDs either facing up or down. Warning The power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. 5 5. Plug the power adapter into a power source and then plug the DC power cord into the DC connector on the front panel of the switch. 6. Make sure the PWR LED on the front panel is green. If the LED is OFF, refer to “Troubleshooting” on page 31. 7.
AT-FS708LE Installation Guide Warranty Registration When you finish installing the product, you should register you product by completing the enclosed warranty card and sending it in. Troubleshooting The following procedure should be perform after you have initially installed the unit to check to be sure that the device is operating properly. You can also perform this procedure to troubleshoot the unit in the event you experience any problems with the device. 1. Check the PWR LED. The LED should be ON.
❑ Verify that the node connected to the port on the switch is powered ON. If the node is OFF, power the unit ON. ❑ Verify that the distance between the switch and the connected network device is no greater than 100 meters (328 feet). ❑ Check to be sure that you are using the correct type of cable: Category 3, 4, or 5 for 10 Mbps operation and Category 5 cable for 100 Mbps operation. ❑ Verify that the cable has not been cut or damaged. 3.
AT-FS708LE Installation Guide Technical Specifications Standards Compatibility: IEEE 802.3, IEEE802.3u Power Supply: Input: 120V @ 1A Connectors: RJ-45 Address Table: Up to 4,000 entries Queue Buffer: 256K bytes Physical Dimensions: WxDxH 14.6 x 8.2 x 2.6 cm (5.8 x 3.3 x 1.0 in) Weight: 350 g (0.
Safety: UL - USA TUV (EN60950) Europe CSA or cUL - Canada C-Tick - Australia CE Mark Immunity: EN55024 34
Appendix A Translated Safety and Emission Information Important: This appendix contains multiplelanguage translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idiomas das advertências de segurança neste guia. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.
AT-FS708LE Installation Guide Standards: This product meets the following standards: U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn, Inc. Manufacture Address: Manufacture Telephone: 950 Stewart Drive, Suite B Sunnyvale, CA 94085 USA 408-730-0950 Declares that the product: Fast Ethernet Switch Model Number: AT-FS708LE This product complies with FCC Part 15, Class B Limits: This device complies with part 15 of the FCC Rules.
Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. 1 RFI Emissions 2 Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 3 Immunity EN55024 4 Electrical Safety UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide 11 USA/CANADA: Use a UL Listed/CSA Certified AC adapter of DC 9V, 1A. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung 2 WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. 3 Störsicherheit EN55024 4 Elektrische Sicherheit UL 1950, CSA C22.2 No.
Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission: FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. 3 Immunitet EN55024 4 Elektrisk sikkerhed UL 1950, CSA C22.2 No. 950, EN60950 SIKKERHED 5 ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN.
AT-FS708LE Installation Guide Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie 2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. 3 Immuniteit 4 Electrische Veiligheid FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) EN55024 UL 1950, CSA C22.2 No. 950, EN60950 VEILIGHEID 5 WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE ONTKOPPELEN.
Normes: ce produit est conforme aux normes de suivantes. 1 Emission d’interférences radioélectriques FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. 3 Immunité EN55024 4 Sécurité électrique UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä 2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. 3 Kestävyys EN55024 4 Sähköturvallisuus UL 1950, CSA C22.2 No. 950, EN60950 FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) TURVALLISUUS 5 HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.
Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. 3 Immunità EN55024 4 Sicurezza elettrica UL 1950, CSA C22.2 No.
AT-FS708LE Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling 2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. 3 Immunitet EN55024 4 Elektrisk sikkerhet UL 1950, CSA C22.2 No. 950, EN60950 FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) SIKKERHET 5 FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET.
Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de radiofrequência FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) 2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. 3 Imunidade EN55024 4 Segurança Eléctrica UL 1950, CSA C22.2 No. 950, EN60950 SEGURANÇA 5 CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE DESCONEXÃO.
AT-FS708LE Installation Guide Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI 2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. 3 Inmunidad EN55024 4 Seguridad eléctrica UL 1950, CSA C22.2 No.
Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning 2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. 3 Immunitet EN55024 4 Elsäkerhet UL 1950, CSA C22.2 No. 950, EN60950 FCC Part 15, EN55022, C-Tick, CISPR 22, VCCI (Class B) SÄKERHET 5 VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln. 6 UTRUSTNING MED PLUGG.
