AT-FS705PD Fast Ethernet Switch Installation Guide PN 613-50465-00 Rev B
Copyright © 2004 Allied Telesyn, Inc. 960 Stewart Drive Suite B, Sunnyvale CA 94085, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Statements Standards: This product meets the following standards: U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Statements RFI Emission FCC Class B, EN55022 Class B, 1 VCCI Class B, C-TICK Immunity EN55024 Electrical Safety EN60950 (TUV), UL60950 (cULus), CE 2 3 Important: Appendix B contains translated safety statements for installing , go to Appendix B for the translated this equipment. When you see the safety statement in your language. Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts.
Table of Contents Electrical Safety and Emission Compliance Statements .....................iii Table of Contents ............................................................................................ v Welcome to Allied Telesyn .......................................................................... vii Where to Find Related Guides......................................................................... vii Documentation Conventions .................................................................
Installing the Switch on a Desktop.................................................................. 15 Wall-Mounting the Switch ............................................................................... 17 Warranty Registration ..................................................................................... 20 Chapter 3 Troubleshooting ............................................................................................ 21 Appendix A Technical Specifications ...............................
Welcome to Allied Telesyn This guide contains instructions on how to install and configure the AT-FS705PD Fast Ethernet Switch. Where to Find Related Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site.
Welcome to Allied Telesyn Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales or corporate information. Online Support You can request technical support online by accessing the Allied Telesyn Knowledge Base from the following web site: http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
Chapter 1 Overview The AT-FS705PD is a 5-port Unmanaged Fast Ethernet Switch that includes one Power-Over-Ethernet (POE) port. This switch is considered a Class 1 Powered Device (PD) and can be used in pair with any IEEE 802.3af/D4.3 or later compliant Power Sourcing Equipment (PSE). This switch offers a range of features and capabilities that can be used in a variety of network configurations and topologies.
Overview Figure 1 illustrates the front and back panels of the AT-FS705PD switch.
AT-FS705PD Fast Ethernet Switch Installation Guide Status LEDs Table 1 defines the LEDs for the switch. Table 1 Status LEDs LED Color Description LINK/ACT Green A valid link has been established on the port. OFF No link has been established on the port. Blinking Data is being received or transmitted on the port. Green The port is operating at 100 Mbps. OFF The port is operating at 10 Mbps. Green The port is operating in full-duplex mode. OFF The port is operating in half-duplex mode.
Overview Powering Options POE 24V D C 24VDC Power Port 5 POE Port 4 3 2 1 Twisted Pair Ports Figure 2 Power Port, POE Port, and Twisted Pair Ports on Back Panel Two ways to power on an AT-FS705PD switch are as follows: ❑ Option 1: Powered by a 24VDC @ 0.3A+ output wall adapter. Option 1 has higher priority, if both options are connected to the AT-FS705PD, then it is powered by Option 1 and the PWR WALL LED is green.
AT-FS705PD Fast Ethernet Switch Installation Guide Port Speed The twisted pair ports are compliant with the 10Base-T and 100Base-TX standards and are capable of either 10 Mbps or 100 Mbps operation. Since the ports are IEEE 802.3u Auto-Negotiation compliant, the switch will set the port speed automatically. With Auto-Negotiation, the speed of the ports are set automatically by the switch after it determines the speed of the end-node connected to the port.
Overview Auto MDI/MDI-X A twisted pair port on a 10 Mbps or 100 Mbps Ethernet network device can have one of two possible wiring configurations: MDI or MDI-X. A twisted pair port on a PC, router, or bridge is typically wired as MDI, while a twisted pair port on a switch or hub is usually MDI-X. To connect two 10 Mbps or 100 Mbps network devices together that have dissimilar port wiring configurations, such as an MDI to MDI-X, you would use a straight-through twisted pair cable.
AT-FS705PD Fast Ethernet Switch Installation Guide The switch also checks the destination MAC address of each frame it receives. The destination address is the MAC address of the end-node to which the frame is intended. If the address is in the table, the switch directs the frame directly to the port where the end-node is located. This helps to ensure that end-nodes will only receive traffic that is intended for them and not have to deal with traffic intended for other end-nodes.
Overview Network Topologies The AT-FS705PD switch can be used in different topologies such as standalone and uplink. Each topology is describe below. Standalone A standalone topology uses one switch to connect the end-nodes. Figure 3 illustrates a standalone topology that uses an AT-FS705PD switch to connect several workstations and a server.
AT-FS705PD Fast Ethernet Switch Installation Guide Uplink Figure 4 illustrates multiple AT-FS705PD switches can be interconnected using uplinks from a centralized backbone Fast Ethernet switch.
Chapter 2 Installation This chapter contains the installation instructions for the AT-FS705PD switch. This switch can be used on a desktop or mounted on a wall. Verifying the Package Contents Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.
Installation Planning the Installation Be sure to observe the following guidelines when planning the installation of your switch. ❑ The end-nodes connected to the twisted pair ports can operate at 10 Mbps or 100 Mbps and half or full-duplex. The switch uses AutoNegotiation to determine the correct speed and duplex mode for each port. ❑ The end-nodes connected to the ports on the switch can be a network adapter card, hub, repeater, router, or another switch.
AT-FS705PD Fast Ethernet Switch Installation Guide Selecting a Site Be sure to observe the following requirements when choosing a site for your switch. ❑ Select a site that is dust-free and moisture-free. ❑ Be sure that the site will allow you to easily access the switch’s power and data cables. ❑ Make sure that the switch is placed on a flat, secure surface (such as a desk or table) if you want to use it with desktop configuration.
Installation Reviewing Safety Guidelines Please review the following safety guidelines before installing the AT-FS705PD switch. Warning Lightning Danger: Do not work on this equipment or cables during periods of lightning activity. 4 Caution Pluggable Equipment: The socket outlet should be installed near the equipment and should be easily accessible. 5 Caution Air Vents: The air vents must not be blocked on the unit and must have free access to the room ambient air for cooling.
AT-FS705PD Fast Ethernet Switch Installation Guide Installing the Switch on a Desktop The AT-FS705PD switch can be used on a desktop or mounted on a wall. To wall-mount the switch, refer to “Wall-Mounting the Switch” on page 17. To install an AT-FS705PD switch on a desktop, perform the following procedure: 1. Remove all equipment from the package and store the packaging material in a safe location. 2.
Installation Caution POE and power cord are used as disconnection devices: To de-energize equipment, disconnect the POE and the power cord. 5. There are two ways to power ON the switch; perform one of the following steps: ❑ Using a wall power adapter: Plug one end of the power cord to the 24VDC power connector on the back of the switch and the other end of the power cord to a power outlet.
AT-FS705PD Fast Ethernet Switch Installation Guide Wall-Mounting the Switch The switch can be mounted horizontally on a wall using the keyholes on the bottom of the switch. The screws, plastic anchors, and other materials necessary to mount the switch on a wall are not provided. To wall-mount the switch, perform the following procedure: 1. If attached, remove the rubber feet, data cables, and power cord from the switch. 2. Select a wall location for the device. 3.
Installation 4. Position the switch horizontally onto the wall screws, as illustrated in Figure 7. R PW E PO LL WA T K/AC LIN 100M X FD 5 4 3 itch D t Sw rne 705P Ethe e -FrtSFast Devic AT 5 Powered 2 1 Po Figure 7 Positioning The Switch Onto The Wall Screws 5. Connect the twisted pair cables to the twisted pair ports. When connecting a twisted pair cable to a port, observe the following guidelines: ❑ An RJ-45 connector should fit snugly into the port on the switch.
AT-FS705PD Fast Ethernet Switch Installation Guide 6. Power ON the switch. There are two ways to power ON the switch; perform one of the following steps: ❑ Using a wall power adapter: Plug one end of the power cord to the 24VDC power connector on the back of the switch and the other end of the power cord to a power outlet. ❑ Using the POE port: Make sure that no power plug is inserted in the 24VDC power port.
Installation Warranty Registration When you have finished installing the switch, you should register your switch by completing the enclosed warranty card and sending it in.
Chapter 3 Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. If the PWR-POE LED is OFF and Port 5 is connected to a PSE device, do the following; Note This twisted pair cable connecting to the POE port must be a Category 5 Ethernet cable. ❑ Make sure that the PSE device is IEEE 802.3af/D4.3 or later compliant. ❑ Make sure that the PSE device is detecting the AT-FS705PD switch. ❑ Make sure that the CAT5 cable is functional.
Troubleshooting ❑ Verify that the end-node connected to the port and the switch are operating at the same speed. Both must be operating at either 10 Mbps or 100 Mbps. ❑ Make sure that the twisted pair cable does not exceed 100 meters (328 feet) and that you are using a Category 3 or better cable for 10Base-T operation or a Category 5 or better cable for 100Base-TX operation.
Appendix A Technical Specifications Physical Dimensions: WxHxD 125.73 mm x 26 mm x 100.05 mm (4.95 in x 1.02 in x 3.74 in) Weight: 372 grams (0.82 lbs) Environmental Operating Temperature: 0° C to 40° C (32° F to 104° F) Storage Temperature: -25° C to 70° C (-13° F to 158° F) Operating Humidity: 5% to 90% non-condensing Storage Humidity: 5% to 95% non-condensing Operating and Storage Altitude: Up to 3,048 meters (10,000 feet) Electrical Rating Input Supply Voltage: 24VDC Input Current: 0.
Technical Specifications Agency Compliance EMI/RFI: FCC Class B, EN55022 Class B, VCCI Class B, C-TICK Electrical Safety: EN60950 (TUV), UL60950 (cULus), CE Immunity: EN55024 Pinout Assignments Figure 8 shows the pinout assignments for the RJ-45 connector. 8 1 8 1 Figure 8 RJ-45 Pin Assignments Table 4 lists the RJ-45 connector pins and their signals used in Port 1 - Port 4 when these port are operating in either MDI or MDI-X configuration.
AT-FS705PD Fast Ethernet Switch Installation Guide Table 5 lists the RJ-45 connector pins and their signals used in Port 5 when this port is connected to a PSE device using a straight cable.
Technical Specifications Table 6 lists the RJ-45 connector pins and their signals used in Port 5 when this port is connected to a PSE device using a cross-over cable.
Appendix B Translated Safety and Emission Information Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety and Emission Information Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Allied Telesyn, Inc. Manufacturer Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Manufacturer Telephone: 408-730-0950 Declares that the product: Fast Ethernet Switch Model Numbers: AT-FS705PD This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
AT-FS705PD Fast Ethernet Switch Installation Guide 1 RFI Emission FCC Class B, EN55022 Class B, VCCI Class B, C-TICK 2 Immunity EN55024 3 Electrical Safety EN60950 (TUV), UL60950 (cULus), CE 4 Lightning Danger Danger: DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY. 5 Pluggable equipment, the socket outlet shall be installed near the equipment and shall be easily accessible.
Translated Safety and Emission Information Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 30 1 Hochfrequenzstörung FCC Klasse B, EN55022 Klasse B, VCCI Klasse B, C-TICK 2 Störsicherheit EN55024 3 Elektrische Sicherheit EN60950 (TUV), UL60950 (cULus), CE 4 Gefahr Durch Blitzschlag Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen.
AT-FS705PD Fast Ethernet Switch Installation Guide Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission FCC Klasse B, EN55022 Klasse B, VCCI Klasse B, C-TICK 2 Immunitet EN55024 3 Elektrisk sikkerhed EN60950 (TUV), UL60950 (cULus), CE 4 Fare Under Uvejr Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
Translated Safety and Emission Information Eisen: Dit product voldoet aan de volgende eisen. 1 32 RFI Emissie FCC Klasse B, EN55022 Klasse B, VCCI Klasse B, C-TICK 2 Immuniteit EN55024 3 Electrische Veiligheid EN60950 (TUV), UL60950 (cULus), CE 4 Gevaar Voor Blikseminslag Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM. 5 Equipement pour branchement electrique, la prise de sortie doit être placée près de l’équipement et facilement accessible".
AT-FS705PD Fast Ethernet Switch Installation Guide Normes: Ce produit est conforme aux normes de suivantes. 1 Emission d'interférences radioélectriques FCC Classe B, EN55022 Classe B, VCCI Classe B, C-TICK 2 Immunité EN55024 3 Sécurité électrique EN60950 (TUV), UL60950 (cULus), CE 4 Danger De Foudre Danger: NE PAS MANIER le matériel ou les CÂBLES lors d'activité orageuse.
Translated Safety and Emission Information Standardit: Tämä tuote on seuraavien standardien mukainen. 34 1 Radioaaltojen häirintä FCC Luokka B, EN55022 Luokka B, VCCI Luokka B, C-TICK 2 Kestävyys EN55024 3 Sähköturvallisuus EN60950 (TUV), UL60950 (cULus), CE 4 Salamaniskuvaara Engenvaara: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA SALAMOINNIN AIKANA. 5 Pistorasiaan kytkettävä laite; pistorasia on asennettava laitteen lähelle ja siihen on oltava esteetön pääsy.
AT-FS705PD Fast Ethernet Switch Installation Guide Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) FCC Classe B, EN55022 Classe B, VCCI Classe B, C-TICK 2 Immunità EN55024 3 Sicurezza elettrica EN60950 (TUV), UL60950 (cULus), CE 4 Pericolo Di Fulmini Pericolo: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI TEMPORALESCHE.
Translated Safety and Emission Information Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 36 1 RFI stråling FCC Klasse B, EN55022 Klasse B, VCCI Klasse B, C-TICK 2 Immunitet EN55024 3 Elektrisk sikkerhet EN60950 (TUV), UL60950 (cULus), CE 4 Fare For Lynnedslag Fare: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR. 5 Utstyr for stikkontakt. Stikkontakten skal monteres i nærheten av utstyret og skal være lett tilgjengelig.
AT-FS705PD Fast Ethernet Switch Installation Guide Padrões: Este produto atende aos seguintes padrões. 1 2 Emissão De Interferência De Radiofrequência FCC Classe B, EN55022 Classe B, VCCI Classe B, C-TICK Imunidade EN55024 3 Segurança Eléctrica EN60950 (TUV), UL60950 (cULus), CE 4 Perigo De Choque Causado Por Raio Perigo: NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis a QUEDAS DE RAIO.
Translated Safety and Emission Information Estándares: Este producto cumple con los siguientes estándares. 38 1 Emisión RFI FCC Clase B, EN55022 Clase B, VCCI Clase B, C-TICK 2 Inmunidad EN55024 3 Seguridad eléctrica EN60950 (TUV), UL60950 (cULus), CE 4 Peligro De Rayos Eligro: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS. 5 Equipo conectable, el tomacorriente se debe instalar cerca del equipo, en un lugar con acceso fácil".
AT-FS705PD Fast Ethernet Switch Installation Guide Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning FCC Klass B, EN55022 Klass B, VCCI Klass B, C-TICK 2 Immunitet EN55024 EN60950 (TUV), UL60950 (cULus), CE 3 Elsäkerhet 4 Fara För Blixtnedslag Fara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER. 5 Utrustning med plugg. Uttaget skall installeras i utrustningens närhet och vara lättåtkomligt".
