AT-FS705L Fast Ethernet Switch Installation Guide PN 613-50326-00 Rev C
Copyright © 2002 Allied Telesyn, Inc. 960 Stewart Drive Suite B, Sunnyvale CA 94085, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Compliance Statements Standards: This product meets the following standards: U.S. Federal Communications Commission Declaration Of Conformity Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Manufacture Telephone: 408-730-0950 Declares that the product: Fast Ethernet Switch Model Numbers: AT-FS705L This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Electrical Safety and Emission Compliance Statements RFI Emission EN55022 Class B ! 1 Immunity EN55024 ! 2 Electrical Safety EN60950 (TUV), UL60950 (cULus) ! 3 Important: Appendix B contains translated safety statements for installing this equipment. When you see the !, go to Appendix B for the translated safety statement in your language. Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts.
Table of Contents Electrical Safety and Emission Compliance Statements .....................iii Welcome to Allied Telesyn .......................................................................... vii Where to Find Web-based Guides ................................................................... vii Documentation Conventions ............................................................................ vii Contacting Allied Teleysn Technical Support................................................
Chapter 2 Installation ....................................................................................................... 9 Verifying the Package Contents ........................................................................ 9 Planning the Installation ................................................................................. 10 Selecting a Site .......................................................................................... 10 Reviewing Safety Guidelines ...........................
Welcome to Allied Telesyn This guide contains instructions on how to install and configure the AT-FS705L Fast Ethernet Switch. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site.
Welcome to Allied Telesyn Contacting Allied Teleysn Technical Support You can contact Allied Telesyn technical support online or by telephone or e-mail. Online Support You can request technical support online by accessing the Knowledge Base at http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
AT-FS705L Switch Installation Guide Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
Welcome to Allied Telesyn Tell Us What You Think If you have any comments or suggestions on how we might improve this or other Allied Telesyn documents, please fill out the General Enquiry Form online. This form can be accessed by selecting “Contact Us” from www.alliedtelesyn.com.
Chapter 1 Overview The AT-FS705L is an unmanaged Layer 2 switch. This switch can be used in a variety of network configurations and topologies. You can use the switch to create small workgroups with dedicated 10 Mbps and 100 Mbps links to your network devices, such as workstations, servers, printers, and routers. You can also use the switch to interconnect Ethernet hubs to provide a bridge between the different workgroups of your network.
Overview Features ❑ LEDs for unit and port status ❑ Auto MDI/MDI-X on the twisted pair ports ❑ Half- or full-duplex operation on both ports ❑ Five RJ-45 twisted pair connectors ❑ Store and forward switching mode ❑ MAC address table with a capacity of 2,000 addresses ❑ Small compact size for use on a desktop or wall-mountable Status LEDs Table 1 defines the LEDs for the switch. Table 1 Status LEDs LED Color Description POWER Green Power is applied to the switch.
AT-FS705L Switch Installation Guide Twisted Pair Ports The AT-FS705L switch has five 10Base-T/100Base-TX twisted pair ports. Each twisted pair port features a RJ-45 connector. The maximum operating distance for the twisted pair ports is 100 meters (328 feet) when operating at either 10 Mbps or 100 Mbps. Port Speed The twisted pair ports are compliant with the 10Base-T and 100Base-TX standards and are capable of either 10 Mbps or 100 Mbps operation. Since the ports are IEEE 802.
Overview Auto MDI/MDI-X An RJ-45 twisted pair port on a 10 Mbps or 100 Mbps Ethernet network device can have one of two possible wiring configurations: MDI or MDI-X. A RJ-45 port on a PC, router, or bridge is typically wired as MDI, while a twisted pair port on a switch or hubs is usually MDI-X. To connect two 10 Mbps or 100 Mbps network devices together that have dissimilar port wiring configurations, such as an MDI to MDI-X, you would use a straight-through twisted pair cable.
AT-FS705L Switch Installation Guide The switch also checks the destination MAC address of each frame it receives. The destination address is the MAC address of the end-node to which the frame is intended. If the address is in the table, the switch directs the frame directly to the port where the end-node is located. This helps to ensure that end-nodes will only receive traffic that is intended for them and not have to deal with traffic intended for other end-nodes.
Overview Network Topologies The AT-FS705L switch can be used in three different topologies: standalone, cascade, and uplink. Each topology is describe below. Standalone A standalone topology uses one switch to connect the end-nodes. Figure 2 illustrates a standalone topology that uses an AT-FS705L switch to connect several workstations and a server.
AT-FS705L Switch Installation Guide Cascade Figure 3 illustrates two AT-FS705L switches connected together to support multiple network segments. This is commonly referred to as ‘cascading.
Overview Uplink Figure 4 illustrates multiple AT-FS705L switches can be interconnected using uplinks from a centralized backbone Fast Ethernet switch.
Chapter 2 Installation This chapter contains the installation instructions for the AT-FS705L switch. This switch can be used on a desktop or mounted on a wall. Verifying the Package Contents Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.
Installation Planning the Installation Be sure to observe the following guidelines when planning the installation of your switch. ❑ The end-nodes connected to the twisted pair ports can operate at 10 Mbps or 100 Mbps and half or full-duplex. The switch uses autonegotiation to determine the correct speed and duplex mode for each port.
AT-FS705L Switch Installation Guide Reviewing Safety Guidelines Please review the following safety guidelines before installing the AT-FS705L switch. Warning Electrical Shock Hazard: To prevent electrical shock, do not remove the cover. There are no user-serviceable parts inside. The unit contains hazardous voltages and should only be opened by a trained and qualified technician. ! 4 Warning Lightning Danger: Do not work on equipment or cables during periods of lightning activity.
Installation Installing the Switch on a Desktop The AT-FS705L switch can be used on a desktop or mounted on a wall. To wall-mount the switch, refer to “Wall-Mounting the Switch” on page 13. To install an AT-FS705L switch on a desktop, perform the following procedure: 1. Remove all equipment from the package and store the packaging material in a safe location. 2. If you are installing the switch on a desktop, attach the four protective feet to the bottom on the unit. See Figure 5.
AT-FS705L Switch Installation Guide Wall-Mounting the Switch The switch can be mounted horizontally on a wall using the keyholes on the bottom of the switch. The screws, plastic anchors, and other materials necessary to mount the switch on a wall are not provided. To wall-mount the switch, perform the following procedure: 1. If attached, remove the rubber feet, data cables, and power cord from the switch. 2. Select a wall location for the device. 3.
Chapter 3 Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. If the POWER LED is OFF, do the following; ❑ Make sure that the power cord is securely connected to the wall outlet and the power connector is securely connected to the back of the switch. ❑ Verify that the power outlet has power by connecting another device to it. ❑ Try using another power cord of the same type that came with your switch.
Troubleshooting If there is a communication problem between the end-nodes connected to the switch, do the following: ❑ Verify that the end-nodes are operating with the same duplex mode. If you are still experiencing problems after testing and troubleshooting the installation, refer to “Contacting Allied Teleysn Technical Support” on page viii or visit our web site at www.alliedtelesyn.com for support information.
Appendix A Technical Specifications Physical Dimensions: WxDxH 197 mm x 117 mm x 37 mm (7.75 in x 4.59 in x 1.45 in) Weight: 0.610 kg (1.35 lbs) Environmental Maximum Operating: 0° to 40° C (32° to 104° F) Maximum Storage: -20° to 80° C (-4° F to 176° F) Relative Humidity Operating and Storage: 5% to 95% (non-condensing) Operating and Storage Altitude: Up to 3,048 meters (10,000 feet) Electrical Rating Input Supply Voltage: 100 - 240 V AC, 50/60 Hz Maximum Current: 0.
Technical Specifications Agency Compliance EMI/RFI: FCC Class B, EN55022 Class B Electrical Safety: cCSAus, Immunity: EN55024 TUV Pinout Assignments Figure 6 shows the pinout assignments for the RJ-45 connector. Pin 8 Pin 1 Figure 6 RJ-45 Pin Assignments Table 3 lists the 10Base-T/100Base-TX connector pins and their signals when the port is operating in either MDI or MDI-X configuration.
Appendix B Translated Safety and Emission Information Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety and Emission Information Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Manufacture Telephone: 408-730-0950 Declares that the product: Fast Ethernet Switch Model Numbers: AT-FS705L This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
AT-FS705L Switch Installation Guide Safety !4 Electrical Notices Warning: Electric Shock Hazard To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables.
Translated Safety and Emission Information !6 Automatische Spannungseinstellung Dieses Gerät stellt sich automatisch auf die auf dem Etikett aufgeführten Spannungswerte ein !7 Vorsicht: Das netzkabel dient zum trennen der stromversorgung. Zur trennung vom netz, kabel aus der steckdose ziehen. !8 Geräte Der Klasse 1 Diese Geräte Müssen Geerdet Sein. Der Netzstecker darf nur mit einer vorschriftsmäßig geerdeten Steckdose verbunden werden.
AT-FS705L Switch Installation Guide ! 11 Betjeningstemperatur: Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C. ! 12 Alle Lande: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer. Eisen: Dit product voldoet aan de volgende eisen.
Translated Safety and Emission Information Normes: ce produit est conforme aux normes de suivantes: !1 Emission d’interférences radioélectriques EN55022 Classe B !2 Immunité EN55024 Sécurité électrique EN60950 (TUV), UL60950 (cULus) !3 Sécurité !4 Information Sur Les Risques Électriques Avertissement: Danger D’électrocution Pour éviter toute électrocution, ne pas ôter le revêtement protecteur du matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur.
AT-FS705L Switch Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. !1 Radioaaltojen häirintä EN55022 Luokka B !2 Kestävyys EN55024 Sähköturvallisuus EN60950 (TUV), UL60950 (cULus) !3 Turvallisuus !4 Sähköön Liittyviä Huomautuksia Varoitus: Sähköiskuvaara Estääksesi sähköiskun älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää vaarallisia jännitteitä ja sen voi avata vain koulutettu ja pätevä teknikko.
Translated Safety and Emission Information Standard: Questo prodotto è conforme ai seguenti standard. !1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B !2 Immunità EN55024 Sicurezza elettrica EN60950 (TUV), UL60950 (cULus) !3 Norme Di Sicurezza !4 Avvertenze Elettriche Attenzione: Pericolo Di Scosse Elettriche Per evitare scosse elettriche non asportare il coperchio. Le componenti interne non sono riparabili dall’utente.
AT-FS705L Switch Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. !1 RFI stråling !2 Immunitet EN55024 !3 Elektrisk sikkerhet EN60950 (TUV), UL60950 (cULus) EN55022 Klasse B Sikkerhet !4 Elektrisitet Advarsel: Fare For Elektrisk Sjokk For å unngå elektrisk sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren kan reparere på innsiden. Denne enheten inneholder farlige spenninger, og må kun åpnes av en faglig kvalifisert tekniker.
Translated Safety and Emission Information Padrões: Este produto atende aos seguintes padrões. !1 Emissão de interferência de radiofrequência EN55022 Classe B !2 Imunidade EN55024 Segurança Eléctrica EN60950 (TUV), UL60950 (cULus) !3 Segurança !4 Avisos Sobre Características Elétricas Atenção: Perigo De Choque Elétrico Para evitar choque elétrico, não retire a tampa. Não contém peças que possam ser consertadas pelo usuário.
AT-FS705L Switch Installation Guide Estándares: Este producto cumple con los siguientes estándares. !1 Emisión RFI EN55022 Clase B !2 Inmunidad EN55024 Seguridad eléctrica EN60950 (TUV), UL60950 (cULus) !3 Seguridad !4 Avisos Electricos Advertencia: Peligro de electrochoque Para evitar un electrochoque, no quite la tapa. No hay ningún componente en el interior al cual puede prestar servicio el usuario.
Translated Safety and Emission Information Standarder: Denna produkt uppfyller följande standarder. !1 Radiostörning EN55022 Klass B !2 Immunitet EN55024 !3 Elsäkerhet EN60950 (TUV), UL60950 (cULus) Säkerhet !4 Tillkännagivanden Beträffande Elektricitetsrisk: Risk för elektrisk stöt För att undvika elektrisk stöt, ta ej av locket. Det finns inga delar inuti som behöver underhållas. Denna apparat är under högspänning och får endast öppnas av en utbildad kvalificerad tekniker.
