AT-FH705E Dual Speed Hub Installation Guide PN 613-10803-00 Rev.
Copyright ”1999 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
FCC Statement STANDARDS: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International, Corp. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Hub Model Number: AT-FH705E This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Safety Warnings Safety Warnings STANDARDS: This product meets the following standards RFI Emmission EN55022 Class B Immunity EN50082-1, 1997 SAFETY Power to the hub must be sourced only from the adapter. USA/CANADA Use a UL Listed/CSA Certified AC adapter of DC 5 V, 2.5 A. EUROPE - EU Use TÜV licensed AC adapter of DC 5 V, 2.5 A. UK Use a UK Safety Approved AC adapter of DC 5 V, minimum 2.5 A. LIGHTNING DANGER DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY.
Table of Contents FCC Statement ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïLLL Safety Warnings ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïï LY Chapter 1 Product Description ïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïïï ì Package Contents ............................................................................
Chapter 1 Product Description The AT-FH705E Mini Hub is an 5-port 10/100 Mbps dual speed hub that offers a cost-effective solution to today’s growing need of network speed integration. With five 10/100 Mbps plug-and-play dual speed ports equipped in its compact body, it is possible to achieve the coexistence of 10 Mbps and 100 Mbps devices in a single network now and step to 100 Mbps network in the future.
Product Description Package Contents The package should include the following items: ‰ One 5-port Dual Speed Mini Hub ‰ One Power Adapter ‰ This Installation Guide If any item is missing, please contact your dealer immediately. Front Panel The front panel contains the hub LED indicators. The LEDs help monitor the hub’s operating status and overall network performance. See Table 1 for further information concerning the LEDs.
Chapter 2 Installation Installing the Mini Hub 1. Place the Hub on a smooth and horizontal surface. 2. Establish network connection by plugging one end of the Category 5 UTP/STP cable RJ45 connector into the hub port, the other end to the Ethernet/Fast Ethernet adapter installed in the workstation computers. (Use Category 5 or above for 100 Mbps; use Category 3, 4, or 5 or above for 10 Mbps.) 3. Connect each device by repeating Step 2. 4. Make sure that each device is connected properly.
Installation Caution The Uplink cable length cannot exceed 5 m (328 ft)when using 100 Mbps. Application The hub can be deployed where 10 Mbps and 100 Mbps network devices coexist and need to be integrated. Figure 2 illustrates a sample application.
Chapter 3 Troubleshooting This chapter describes the procedures to test and troubleshoot the hub. Connectivity Testing In the following procedure, you will test each port for a valid connection and to confirm the correct operation of the network. 1. Start with Ports 1 and 2. Connect these two ports of a single hub to two nodes or workstations and turn on the hub’s power supply. 2. Make sure the Link/Activity and other LEDs of both hub ports are lit. 3.
Troubleshooting Problem Solving Is the unit receiving power? Check the Power LED on the front of the hub. This green LED should be lit. If the Power LED is not on: 1. Check the back of the unit. Make sure the power cord is attached securely. 2. Check the AC power adapter. Make sure the power adapter is plugged into a functioning wall outlet and that it is properly inserted into the hub’s power connector on the back of the unit.
AT-FH705E Installation Guide Problem 3: Port 1 does not operate properly. Solution 3: The Uplink slide switch may be in the wrong position. Check the following: ‰ When using the cascade port of the hub (Port 1), you should set the slide switch to the 8SOLQNýposition. ‰ When cascading two hubs, the unit using the cascade port should have the button set to the 8SOLQN position, while the other unit should have its switch set WRý1RGH.
Appendix A Technical Specifications Physical Characteristics 10/100Base-TX Port 5 auto-negotiate ports Uplink Port Port 1 Cabling UTP/STP Category 5 for 100 Mbps; UTP Category 3, 4, or 5 for 10 Mbps Maximum of 100 m (328 ft) between the hub and a network node Operating Temperature 0 ~ 40o C (32~104o F) Operating Humidity 5 ~ 95% Storage Temperature 0 ~ 70o C (32~158o F) Storage Humidity 5 ~ 95% Chassis Dimensions 5.2 in x 4.9 in x 1.2 in (131 mm x 123 mm 30 mm) Weight 1.25 lb (0.
Technical Specifications Agency Compliance Standard IEEE 802.3 (10Base-T) and IEEE 802.3u (100Base-TX) Class I and II Repeater EMI/RFI FCC Part 15 Class B, EN55022 Class B Immunity EN 50082-1 Safety Complies with safety standards UL 1950, cUL, EN60950 CE Compliant UTP (RJ45) Connector Figure 3 shows an RJ45 connector. For a 100Base-TX link between hubs, —any two Medium Attachment Units (MAUs)—you need a crossover cable.
AT-FH705E Installation Guide Cabling Specifications Table 2 provides an overview of IEEE 802.3 and 802.3u cabling specifications for 10Base-T, and 100Base-TX network configurations using twisted-pair cable. Table 2 IEEE 802.3 and 802.
Technical Specifications 100Base-TX Connector Pinouts Straight-through Cable 12 Crossover Cable 4#7;. 5#7;0 6#5;. 7;.#4 7;0#5 5;.#6 4#7;. 5#7;0 6#5;. 7;.#4 7;0#5 5;.
Appendix B Technical Support Fax Order Name ___________________________________________________________________ Company ________________________________________________________________ Address _________________________________________________________________ City ________________________ State/Province ________________________________ Zip/Postal Code ___________________ Country_________________________________ Phone _______________________________Fax_________________________________ Incident Summary Mode
Appendix C AT-FH705E Switch Installation Feedback Please tell us what additional information you would like to see discussed in the guide. If there are topics you would like information on that were not covered in the guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of the guide.
Appendix D Where To Find Us For Technical Support or Service Location Phone Fax Americas United States, Canada, Mexico, Central America, South America 1 (800) 428-4835 1 (918) 628-3222 Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India (+65) 3815-613 (+65) 3833-830 Australia Australia, New Zealand (+61) 2-943-5111 (+61) 2-9438-4966 France France, Belgium, Luxembourg, The Netherlands, Middle East, Africa (+33) 1-60-92-15-32 (+33) 1-69-28-37-49 Germany Germ
