AT-9900s Series Switch Expansion Module Installation Guide AT-A60 AT-A61 AT-A62
AT-9900s Series Switch Expansion Module Installation Guide AT-A60 AT-A61 AT-A62 Download the complete document set from www.alliedtelesis.
AT-9900s Series Switch Expansion Module AT-9900s Series Switch Expansion Module Installation Guide Document Number 613-000790 REV A © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice.
Installation Guide Contents About this Guide .............................................................................................................. 4 Package Contents ............................................................................................................. 4 Overview ............................................................................................................................ 4 AT-A60 10 Gigabit XFP Port .............................................................
AT-9900s Series Switch Expansion Module About this Guide This Installation Guide describes how to install the following expansion modules in an AT-9900s Series switch: ■ AT-A60, single XFP port ■ AT-A61, 12 SFP ports ■ AT-A62, 12 10/100/1000Mbps RJ-45 ports You can download the complete document set for AT-9900s Series switches from www.alliedtelesis.com/support/software. For more information about the document set and other resources, see “Obtaining Documentation and Resources” on page 11.
Installation Guide AT-A60 10 Gigabit XFP Port The AT-A60 single-port 10Gigabit Ethernet expansion module features: ■ one XFP port ■ LEDs showing port status ■ 32MBytes of DDR SDRAM for packet buffering ■ support for hot-swappable XFP transceiver modules AT-A60 Front view AT-A60 L/A XFP L/A LINK ACT XFP ENABLED DISABLED FAULT The following LEDs report operations and faults on the AT-A60.
AT-9900s Series Switch Expansion Module The following XFP transceiver modules are approved for use with the AT-A60. Product No. Media Type Description AT-XPSR 10GBASE-SR 850nm short-haul transmission, 300m with MMF. AT-XPLR 10GBASE-LR 1310nm medium-haul transmission, 10km with SMF. AT-XPER40 10GBASE-ER 1550nm long-haul transmission, 40km with SMF. For the latest list of approved XFP transceiver modules, contact your authorised Allied Telesis distributor or reseller.
Installation Guide AT-A61 1000BASE-X SFP Ports The AT-A61 12-port 1000BASE-X expansion module features: ■ two rows of 6 SFP ports ■ LEDs showing port status ■ 32MBytes of DDR SDRAM for packet buffering ■ support for hot-swappable SFP modules AT-A61 Front view AT-A61 The following LEDs report operations and faults on the AT-A61. LED State Description SFP Green An SFP transceiver is installed and a link has been established.
AT-9900s Series Switch Expansion Module The following SPF modules are approved for use with the AT-A61. Product No. Media Type AT-SPTX 10/100/1000BASE-T Copper, 100m at 1000Mbps, RJ-45 connector. AT-SPSX 1000BASE-SX 850nm, 2 to 550 m with 50/125µm MM fibre, 2m to 275m with 62.5/ 125µm MM fibre, LC connector. AT-SPLX10 1000BASE-LX 1310 nm, 2 m to 10km with 9µm SM fibre, 2 m to 550 m with 50µm MM fibre, 2m to 550m with 62.5µm MM fibre, LC connector.
Installation Guide AT-A62 10/100/1000BASE-T RJ-45 Ports The AT-A62 12-port RJ-45 expansion module features: ■ two rows of 6 RJ-45 ports ■ gigabit ports that support speeds of 10/100/1000Mbps ■ LEDs showing port status ■ 32MBytes of DDR SDRAM for packet buffering ■ cable fault detection and distance-to-fault diagnostics (see the Test Facility chapter in the Software Reference for the switch) AT-A62 Front view AT-A62 The following LEDs report operations and faults on the AT-A62.
AT-9900s Series Switch Expansion Module Installation Procedure Before you begin: ■ Unpack the expansion module. In an anti-static environment, remove the expansion module from its packing material. Be sure to observe ESD precautions. Caution Failure to observe proper anti-static procedures may damage the unit. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller. ■ Verify the package contents if you have not already done so.
Installation Guide 8. If you disconnected a redundant power supply, reconnect it. 9. Restart the switch and verify installation with the show log command to confirm there is no error message about installation in the log file. If you are connected to the asyn0 port, any error message is displayed during startup self-tests.
AT-9900s Series Switch Expansion Module AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for transferring software versions, configuration scripts and other files between a PC and the switch. You download AT-TFTP Server from www.alliedtelesis.com/support/software.
