AT-9006SX/SC AT-9006LX/SC Gigabit Ethernet Switch Quick Install Guide PN 613-10853-00 Rev B
Copyright 2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
Electrical Safety and Emission Compliance Statement Standards: This product meets the following standards. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents Electrical Safety and Emission Compliance Statement .......................iii Welcome to Allied Telesyn .......................................................................... vii Where to Find Web-based Guides ................................................................... vii Document Conventions ................................................................................... viii Contacting Allied Telesyn ......................................................................
Welcome to Allied Telesyn The guide contains instructions on how to install the AT-9006SX/SC and AT-9006LX/SC Gigabit Ethernet Switches. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products. For product guides, you can go directly to the following web page: www.alliedtelesyn.com/support/lib_allproducts.htm.
Document Conventions This guide uses several conventions that you should become familiar with first before you begin to install the product. Note A note provides additional information. Caution A caution indicates that performing or omitting a specific action may result in equipment damage or loss of data. Warning A warning indicates that performing or omitting a specific action may result in bodily injury.
AT-9006 Quick Install Guide Australia Tel: 1 (800) 000-880 Fax: (+61) 2-9438-4966 Japan Tel: (+81) 3-3443-5640 Fax: (+81) 3-3443-2443 France France, Belgium, Luxembourg, The Netherlands, Middle East, Africa Tel: (+33) 0-1-60-92-15-25 Fax: (+33) 0-1-69-28-37-49 United Kingdom United Kingdom, Denmark, Norway, Sweden, Finland Tel: (+0044) 1235-442500 Fax: (+44) 1-235-442680 Technical Support E-mail Addresses United States and Canada TS1@alliedtelesyn.
FTP Server If you need a driver for an Allied Telesyn device and you know the name of the driver, you can download it by connecting directly to our FTP server at ftp://gateway.centre.com. At login, enter ‘anonymous’. Enter your e-mail address for the password as requested by the server at login. For Sales or Corporate Information Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191 Allied Telesyn International, Corp.
AT-9006 Gigabit Ethernet Switch The AT-9006 Gigabit Ethernet switch provides the following features: " Gigabit Ethernet connectivity " A small 1.5U high, 19-inch rackmountable enclosure " Built-in management functions for extremely flexible operation in a standalone configuration " Two slots for optional expansion modules. Table 1 lists the available switch models.
Figure 1 shows the front panel of the AT-9006SX/SC switch.
AT-9006 Quick Install Guide Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the Ethernet switch. Warning Class 1 laser product. ! 6 Warning Do not stare into the laser beam. ! 7 Warning Electric Shock Hazard: To prevent electric shock, do not remove the cover. There are no user-serviceable parts inside. The unit contains hazardous voltages and should only be opened by a trained and qualified technician.
Caution Operating Temperature: This product is designed for a maximum ambient temperature of 40°C. ! 14 Caution All Countries: Install this product in accordance with local and National Electric Codes. ! 15 Installing the Switch On a Desktop The switch can be installed in a standard 19-inch rack or as a standalone unit, such as on a table or desktop. To install the switch in a rack, go to the section “Installing the Switch in a Rack” on page 6.
AT-9006 Quick Install Guide 5. Apply AC power to the switch by plugging the power cord into the AC power connector on the back panel of the unit (shown in Figure 3) and plugging the other end into a wall outlet. RPS Power Connecto AC Power Connector Figure 3 Switch Rear Panel As power is applied to the switch, the Fault LED (shown in Figure 4) flashes as the switch runs a series of internal self tests.
Installing the Switch in a Rack To install the switch in a standard 19-inch rack, perform the following procedure: 1. Remove all components from the shipping package and store the packaging material in a safe location. 2. To prepare the switch, place it on a level, secure surface. 3. If you purchased an expansion module for the switch, install the module by following the instructions in the AT-A15/SX, AT-A15/LX, AT-A16, AT-A17, AT-A18, and AT-A19 Quick Install Guide.
AT-9006 Quick Install Guide Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. ! 13 7. If you purchased a redundant power supply (RPS) unit for the switch, connect the RPS unit to the R.P.S. Input connector (Figure 3) on the rear of the switch by following the directions included with the RPS system.
Setting Up for Local Management If you are installing the switch in a TCP/IP environment or if you intend to manage the switch from a remote site, you must first assign an IP address to the switch using the Omega management software, which comes pre-installed on the switch. To connect a terminal to the switch and start an Omega management session, perform the following steps: 1. Connect a terminal to the RS232 connector on the front panel of the switch. Use an RS232, DB-9 straight-through cable. 2.
AT-9006 Quick Install Guide Switch LEDs Table 2 and Table 3 describe the functions of the LEDs on the Ethernet switch. Table 2 Power and Fault LEDs LEDs State Description Fault Solid Red The switch or management software is malfunctioning. Flashing Red The switch is booting, running diagnostic tests, writing images to FLASH, or transferring files using XMODEM. OFF Normal operation. RPS Solid Green The RPS is connected to the switch.
AT-S26 Software Default Setting Table 4 lists the default settings for the AT-S26 software that comes preinstalled on the Ethernet switch. Table 4 Ethernet Switch Default Settings Settings Default IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Gateway Address 0.0.0.
AT-9006 Quick Install Guide R.P.S. Input Connector Specifications Table 5 lists the pin assignments for the R.P.S. Input connector on the back of the switch. (Pin numbers 1 through 8 are the bottom row of pins on the connector, with pin 1 in the bottom right corner. Pin numbers 9 through 16 are the top row, with pin 9 in the top right position on the connector.
Technical Specifications Table 6 lists the switch specifications. For more information, refer to Appendix B of the AT-9006 Ethernet Switch Installation Guide. Table 6 Technical Specifications Physical Specifications Dimensions (H x W x D) 6.48 cm x 42.93 cm x 35.60 cm (2.55 in x 16.9 in x 14.0 in) Weight 6.12 kg (13.60 lbs) Required Ventilation (all sides) 19 cm (7.
Appendix A Translated Electrical Safety Emission Information Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Standards: This product meets the following standards. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AT-9006 Quick Install Guide ! 13 CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling. ! 14 OPERATING TEMPERATURE: This product is designed for a maximum ambient temperature of 40° degrees C. ! 15 ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Standarder: Dette produkt tilfredsstiller de følgende standarder. !1 Radiofrekvens forstyrrelsesemission !2 ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. !3 Immunitet EN50082-1 1997 !4 Elektrisk sikkerhed EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A SIKKERHED !6 ADVARSEL Laserprodukt av klasse 1. !7 ADVARSEL Stirr ikke på strålen.
AT-9006 Quick Install Guide Eisen: Dit product voldoet aan de volgende eisen. !1 RFI Emissie !2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. !3 Immuniteit EN50082-1 1997 !4 Electrische Veiligheid EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A VEILIGHEID !6 WAARSHUWING Klasse-1 laser produkt. !7 WAARCHUWING Neit in de straal staren.
Normes: ce produit est conforme aux normes de suivantes: !1 Emission d’interférences radioélectriques EN55022 Classe A !2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. !3 Immunité EN50082 - 1 1997 !4 Sécurité électrique EN60950, UL1950, CSA 950 !5 Laser EN60825 SÉCURITÉ !6 ATTENTION Producit laser di classe 1. !7 ATTENTION Ne pas fixer le faisceau des yeux.
AT-9006 Quick Install Guide Standardit: Tämä tuote on seuraavien standardien mukainen. !1 Radioaaltojen häirintä !2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. !3 Kestävyys EN50082-1 1997 !4 Sähköturvallisuus EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Luokka A TURVALLISUUS !6 VAROITUS Luokan 1 Lasertuote. !7 VARIOTUS Älä katso säteeseen.
Standard: Questo prodotto è conforme ai seguenti standard. !1 Emissione RFI (interferenza di radiofrequenza) !2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. !3 Immunità EN50082-1 1997 !4 Sicurezza elettrica EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Classe A NORME DI SICUREZZA !6 AVVERTENZA Prodotto laser di Classe 1.
AT-9006 Quick Install Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. !1 RFI stråling !2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. !3 Immunitet EN50082-1 1997 !4 Elektrisk sikkerhet EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A SIKKERHET !6 ADVARSEL Laserprodukt av klasse 1. !7 ADVARSAL Stirr ikke på strålen.
Padrões: Este produto atende aos seguintes padrões. !1 Emissão de interferência de radiofrequência !2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. !3 Imunidade EN50082-1 1997 !4 Segurança Eléctrica EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Classe A SEGURANÇA !6 AVISO Produto laser de classe 1 !7 AVISO Não olhe fixamente para o raio.
AT-9006 Quick Install Guide Estándares: Este producto cumple con los siguientes estándares. !1 Emisión RFI !2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. !3 Inmunidad EN50082-1 1997 !4 Seguridad eléctrica EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Clase A SEGURIDAD !6 ¡ADVERTENCIA! Producto láser Clase 1.
Standarder: Denna produkt uppfyller följande standarder. !1 Radiostörning !2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. !3 Immunitet EN50082-1 1997 !4 Elsäkerhet EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klass A SÄKERHET !6 VARNING! Laserprodukt av klass 1. !7 VARNING! Laserstrålning när enheten är öppen.
Appendix B Technical Support Fax Order Name _________________________________________________________________ Company ______________________________________________________________ Address _______________________________________________________________ City______________________ State/Province_______________________________ Zip/Postal Code ________________ Country_______________________________ Phone ______________________________ Fax________________________________ Incident Summary Model number of Allie
Appendix C AT-9006 Quick Install Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of this guide.
