AT-6101GP Power over Ethernet Injector AT-6101GP PoE Injector Installation Guide 613-001673 Rev B
Copyright © 2012 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc.
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Declaration of Conformity Manufacturer Name: Allied Telesis, Inc. Declares that the product: PoE Ethernet Injector Model Numbers: AT-6101GP This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Chapter : Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” posted on the Allied Telesis website at www.alliedtelesis.com.
Table of Contents Preface .............................................................................................................................................................. 7 Document Conventions................................................................................................................................ 8 Allied Telesis Contact Information................................................................................................................ 9 Chapter 1: Overview ....
Contents 2
List of Figures Figure 1. AT-6101GP PoE Injector ......................................................................................................................................14 Figure 2. AC Power Input Connector...................................................................................................................................14 Figure 3. AT-6101GP LEDs.....................................................................................................................................
Figures 4
List of Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Twisted Pair Cable for the 10/100/1000Base-T Ports ..........................................................................................13 10/100Base-TX Port LEDs ..................................................................................................................................15 Physical Specifications ..................................................................................................
Tables 6
Preface This guide contains the installation instructions for the AT-6101 PoE Injector Installation Guide.
Preface Document Conventions This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury.
AT-6101 PoE Injector Installation Guide Allied Telesis Contact Information If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support.
Preface 10
Chapter 1 Overview This chapter contains the following sections: “Features” on page 12 “Hardware Description” on page 14 “LEDs” on page 15 11
Chapter 1: Overview Features Here are the features of this product: AT-6101GP PoE Injector 10/100/1000 Mbps Twisted Pair Ports LEDs Installation Options Wiring Configuration Maximum Distance 12 The major features of the AT-6101GP PoE Injector are: Power over Ethernet Injector for 10/100/1000BaseT Remote power feeding Overload and short circuit protection Mixes Ethernet and power into RJ-45 port Delivers power up to 100 meters Light weight and compact size Plug-and-Play
AT-6101 PoE Injector Installation Guide Cable Requirements Port Pinouts The cable requirements of the ports are given in Table 1. Table 1. Twisted Pair Cable for the 10/100/1000Base-T Ports Cable Type 10Mbps 100Mbps 1000Mbps Standard TIA/EIA 568-Bcompliant Category 3 shielded or unshielded cabling with 100 ohm impedance and a frequency of 16 MHz.
Chapter 1: Overview Hardware Description The AT-6101GP PoE Injector is shown in Figure 1. Figure 1. AT-6101GP PoE Injector DATA IN Port: This port, shown in Figure 1, in is an RJ-45 Ethernet connector where data is received and transmitted through the AT-6101GP PoE Injector. DATA OUT Port: This port, shown in Figure 1, is an RJ-45 Ethernet connector where data is received and transmitted through the AT-6101GP PoE Injector and provides PoE power along with the Ethernet data to a PoE device.
AT-6101 PoE Injector Installation Guide LEDs The LEDs of the AT-6101GP PoE Injector are shown in Figure 3 and described in Table 2. Figure 3. AT-6101GP LEDs Table 2. 10/100Base-TX Port LEDs LED State Off AC Power Solid Green Off PoE Power Solid Green Description No AC power is being provided to the unit. AC power is being provided to the unit. The port is not providing PoE power to the DATA OUT port. The port is providing PoE power to the DATA OUT port.
Chapter 1: Overview 16
Chapter 2 Installation You may install the AT-6101GP PoE Injector on a table or on a wall.
Chapter 2: Installation Reviewing Safety Precautions Please review the following safety precautions before you begin to perform the installation procedure. Note The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements. Warning To prevent electric shock, do not remove the cover. No userserviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician.
AT-6101 PoE Injector Installation Guide Warning Only trained and qualified personnel are allowed to install or replace this equipment. E14 Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
Chapter 2: Installation Choosing a Site for the AT-6101GP PoE Injector Observe these guidelines when planning the installation of the AT-6101GP 20 If you plan to install the power injector on a table, the table should be level and stable. The power outlet should be located near the power injector and be easily accessible. The site should allow for easy access to the ports on the front of the power injector, so that you can easily connect and disconnect cables, and view the port LEDs.
AT-6101 PoE Injector Installation Guide Unpacking the AT-6101GP PoE Injector The AT-6101GP PoE Injector comes with the items listed in Table 4. Verify that the contents of the shipping container matches the items listed. If any item in the shipping container is missing or damaged, contact your Allied Telesis sales representative for assistance.
Chapter 2: Installation Installation Procedures Depending on where you install the unit. perform the following procedures when installing the AT-6101GP PoE Injector: Table Top Installation ”Table Top Installation” or ”Wall Installation” “Ethernet Cable Installation” on page 23 “AC Power Cord Installation” on page 24 For installation of the AT-6101GP PoE Injector on a table top, perform the following procedure: 1.
AT-6101 PoE Injector Installation Guide 2. Install the two wall anchors into the wall at the locations marked in the previous step. The anchors require 0.635 mm (0.25 in.) holes. 3. Hold the power injector on the wall so that the mounting holes align with the anchors previously installed. Secure the unit with the two wall mounting screws as shown in Figure 6. Figure 6. Securing the AT-6101GP PoE Injector to the Wall 4. Go to ”Ethernet Cable Installation” for the next step in the installation.
Chapter 2: Installation AC Power Cord Installation Depending on your installation, connect the AC power cord as shown in Figure 8 (table top installation) or Figure 9 (wall installation). Figure 8. Connecting AC Power Cord for Table Top Installation Figure 9.
Chapter 3 Troubleshooting This chapter contains suggestions on how to troubleshoot the installation of the AT-6101GP PoE Injector if a problem occurs. Problem: All PoE injector LEDs are off even though the ports are connected to network devices. Solution: Verify that AC power is connected to the AT-6101GP PoE Injector.
Chapter 3: Troubleshooting 26
Appendix A Technical Specifications Physical Specifications Table 3. Physical Specifications Dimensions (H x W x D) 36 mm x 65 mm x 140 m Weight 300 grams (0.66 lb) Environmental Specifications Table 4. Environmental Specifications Operating Temperature 0° C to 40° C (32° F to 104° F) Storage Temperature 20° C to 80° C (-29° F to 27° Operating Humidity 10% to 90% noncondensing Storage Humidity 10% to 95% noncondensing Power Specifications Table 5.
Appendix A: Technical Specifications Certifications Table 6. Certifications EMI (Emissions) FCC Class B, CE EMC (Immunity) EN55024 Electrical Safety EN60950-1 (TUV), UL 60950-1 (CULUS) Quality and Reliability MTBF > 116685 hrs @ 25° C Compliance Marks CE, CULUS, TUV, C-Tick RJ-45 Twisted Pair Port Pinouts Figure 10 illustrates the pin layout of the RJ-45 connectors and ports. Figure 10. RJ-45 Socket Pin Layout (Front View) Table 7 lists the pin signals for 10 and 100 Mbps. Table 7.
AT-6101 PoE Injector Installation Guide Table 8 lists the pin signals when a port operating at 1000 Mbps. Table 8.
Appendix A: Technical Specifications 30
