Installation Instructions for Topload Washers INSI1GC.......2.0ccceececececececeeeseeeeeees Washer Dimensions...............cceeeeecceceeeeeececeseesesteceeccseesenees Before You Start. .......c ccc ccceeeeeeccceceeenseeceseesenecesecsennenes Trstallation. oo... ccceceeeeeccecesesesceccceceeeneceecesersesseeeeccesenennes Installer Checklist....0 0.
Washer Dimensions |-—_____-. 28 in. (71.1 cm) —_____ |e. 22.13 in. (56.2 cm) ——+| Sh t_| | oO © rm = an 3 - £ ~T o £ Ss oO b&2 6» #+ £& £ oO 5 — > + £ & o ip + * 6&8 © =oO¢ : a S 4 — ¢ & ie 1 g EY ? o s &. Le © Q 25.625 in. (65 cm) ——_-» 2 = 0.4 in. +} J (10.2mm) j—__._ Sg = 2g 26 in. (66 cm) —__ TLW2075N *With leveling legs turned into base. Figure 1 Before You Start Parts Included Supplies An accessories bag has been shipped inside your washer.
Installation Step 2: Wipe Out Inside of Washtub Step 1: Remove the Shipping Brace and Shipping Plug Prior to first wash, use an all purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washtub. Remove the shipping brace from under the lid. The shipping plug will be released from the base of the washer when removing the cardboard base from the washer. Refer to Figure 3. NOTE: Do not tilt washer to front or sides when moving.
Step 3: Connect Fill Hoses A NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer. WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes.
Step 4: Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch (32 cm) outside diameter drain hose.
If standpipe is lower than 36 inches (91.44 cm), you must install No. 562P3 Siphon Break Kit. Refer to Figure 8. This kit is available (as optional equipment at extra cost) through an authorized dealer or parts distributor. Installation instructions are supplied with the kit. Laundry Tub Installation: For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from disloding during use. Refer to Figure /0.
Step 5: Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing. Place washer in position on a clean, dry and reasonably firm floor. Installing the washer on any type of carpeting is not recommended. For easier access to leveling legs, prop up washer with a wooden block. Refer to Figure 1/. Place rubber feet (supplied in accessories bag) on all four leveling legs. Refer to Figure 12.
Step 6: Plug in the Washer When plugging in the washer: Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-Prong grounding plug. Refer to serial plate for specific electrical requirements. e DONOT overload circuits. e DO NOT use an extension cord. e DO NOT use an adapter. e DO NOT operate both a washer and gas dryer on the same circuit. Use separately fused 15 Amp circuits.
Grounding Information Step 7: Add Water to the Washer The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. To prevent damage to pump, do not run washer before adding at least one quart water to the tub. If the washer is run before any water is added, the pump seal may overheat causing the pump to leak.
Step 8: Check Lid Switch Washer should stop agitating and spinning when lid is opened. W376i Figure 15 Step 9: Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly. Run washer through one complete cycle to make sure it is operating properly.
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) Remove the Shipping Brace and Shipping Plug. ¢ Position and Level the Washer. iggy TEINALEAE * W316i * } Plug in the Washer. TLW2000N ° D254! 6) : * Connect Fill Filter Screens Cold Valve Connection « Hoses. . Add Water to the Washer. Hot Valve Connection Plain Washers | CHECK ¢ TLW1988N Connect Drain Hose to Drain Receptacle.
