Specifications

ManualsBrandsAlliance Laundry Systems ManualsComputer equipmentUniLinc

Tie-in to Existing Floor, in. [mm]

Description

L-speed,

45 (M-

speed)

65 (M-

speed)

45-65

(V-

speed)

85-105 130-160

C Distance between

reinforcing bars

(maximum)

Standard* 12 [305] 12 [305] 12 [305] 12 [305] 12 [305]

Narrow* 6 [152] 6 [152] 6 [152] 6 [152] 6 [152]

Ultra-narrow* 6 [152] 6 [152] 6 [152] 6 [152] 6 [152]

D Length of reinforcing bar extend-

ing into existing floor (minimum)

2.5 [64] 2.5 [64] 2.5 [64] 2.5 [64] 2.5 [64]

* Refer to Floor Layout.

Table 12

Machine Mounting and Grouting

NOTE: After the concrete has cured completely and the

cast-in-place method was used, refer to Figure 14 and

proceed to step 7. If acrylic adhesive anchors are de-

sired, refer to Figure 13 and proceed with step 1 after

concrete has cured completely.

1. Refer to Figure 13 to set the drill depth gauge.

2. Drill the holes to the set depth.

3. Use compressed air or squeeze bulb to clean out debris from

each hole. Use a vacuum to remove fine dust.

4. Fill half the hole depth with an industry-accepted adhesive an-

choring system.

5. Insert anchor bolt until it reaches the bottom and a minimum

of 2.75 in. [70 mm] extends above surface and a minimum of

6 inches [152 mm] is embedded in concrete.

6. Ensure all air pockets are removed from adhesive surrounding

the bolt.

7. Allow adhesive around bolt to cure completely.

IMPORTANT: Refer to bolt manufacturer’s recom-

mended adhesive cure times.

8. Remove shipping materials and place the machine carefully

over the bolts. Never attempt to lift the machine by the door

handle or by pushing on the cover panels. Always insert a pry

bar or other lifting device under the bottom frame of the ma-

chine to move it.

9. Raise and level the machine 0.5 inch [12.7 mm] off the floor

on four corners, using spacers such as nut fasteners.

WARNING

Crush hazard. To avoid personal injury and/or

property damage, do not tip the machine more

than 25 degrees in any direction.

W793

10. Following the manufacturer's instructions, mix a good quality

non-shrinking machinery precision grout. The grout should

not be too runny or too dry and should flow into place easily.

Completely fill the space between the machine base and the

floor with grout to ensure a stable installation. Grout com-

pletely under frame (if bolted with inside pattern, remove

front panel and back panel to gain access to all frame mem-

bers). Refer to Figure 15 . Force grout under machine base

until all voids are filled.

IMPORTANT: Minimum Grade 5, SAE rating, flat

washers and minimum Grade 5, SAE rating, serrated

hex flange locknuts are the recommended hardware

for anchoring machine to bolts.

11. Position the flat washers and locknuts on the anchor bolts and

finger-tighten to machine base.

12. Allow machine grout to set (stiffen), but not cure.

13. Remove the spacers carefully, allowing the machine to set-

tle into the wet grout. Pack any remaining voids with grout.

14. After the grout is completely cured, torque the locknuts to 160

± 16 ft.-lbs. – one after the other – until all are tightened even-

ly and the machine is fastened securely to the floor.

IMPORTANT: Refer to recommended grout cure

times from manufacturer before torquing locknuts.

NOTE: Check and retighten the locknuts after five to

ten days of operation and every month thereafter.

Specifications and Dimensions