Installation/Operation Automatic Washers Metered Commercial TLW12C TLW12C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Part No.
WARNING For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. W022 IMPORTANT: Read the complete INSTALLATION/OPERATION INSTRUCTIONS before using the washer.
Table of Contents Safety Information.............................................................................. Explanation of Safety Messages........................................................... Important Safety Instructions ............................................................... 3 3 3 Installation........................................................................................... Dimensions and Specifications.............................................................
Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific instructions. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. Save These Instructions DANGER Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
Safety Information 7. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. This is a safety rule for all appliances. 8.
Installation Dimensions and Specifications 22.44 in. (57 cm) 25.625 in. (65.1 cm) 0.44 in. (1.12 cm) 51 in. (129.54 cm) 41.25 in. (104.78 cm) 36 in. (91.44 cm) 30.5 in. (74.47 cm) 28.75 in. (73.02 cm) H 38.19 in. (97 cm) C Standard Capacity Meter Case 43 in. (109.2 cm) High Capacity Meter Case 43.875 in. (111.44 cm) 1 26 in. (66.04 cm) 28 in. (71.
Installation Before You Start Installing the Washer Tools Step 1: Remove the Shipping Brace and Shipping Plug For most installations, the basic tools you will need are: 1 2 3 Remove the shipping brace from under the lid. The shipping plug will be released from the base of the washer when removing the cardboard base from the washer. Refer to Figure 2. The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location.
Installation Step 2: Wipe Out Inside of Washtub Water Supply Requirements Prior to first wash, use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub. Water supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used.
Installation Connecting Hoses Insert rubber washers and filter screens (from accessories bag) in water fill hose couplings (two hoses supplied with washer). Connect fill hoses to water supply faucets. Then connect the hoses to the hot and cold valve connections at the rear of the washer. Refer to Figure 4. Thread hose couplings onto valve connections finger tight. Then turn 1/4 turn with pliers. IMPORTANT: DO NOT cross thread or overtighten couplings.
Installation Step 4: Connect Drain Hose to Drain Receptacle If necessary, follow the instructions for your type of drain receptacle (high standpipe or low standpipe) to properly install the drain hose. Drain Facilities High Standpipe Installation IMPORTANT: The drain hose installation is a very important factor in the washer installation. If care is not taken when the drain hose is installed, a siphoning action can be started which will cause water to be siphoned from the washer during the cycle.
Installation Low Standpipe Installation If the drain facility is lower than the cabinet top, a siphon break kit, Part No. 562P3, must be installed in the drain hose to prevent siphoning action and drain hose MUST be cut to fit the washer installation. Refer to Figure 8. Use one No. 25863 Hose Coupling to splice hose. The No. 562P3 Siphon Break Kit and No. 25863 Hose Coupling are available as optional equipment at extra cost through an authorized dealer or parts distributor.
Installation Step 6: Plug In the Washer Electrical Requirements 2 (120 Volt, 60 Hertz with 3-Prong Grounding Plug) 3 1 NOTE: The wiring diagram is located in the control hood. 120±12 V.A.C. 0 V.A.C. WARNING To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply.
Installation Grounding Instructions The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. NOTE: The agitator should not be removed except for service. The washtub is designed to be selfcleaning. The washer is equipped with a cord having an equipment-grounding conductor and a three-prong grounding plug.
Installation Vending Models Prepped for Card Reader Meter Case The machine is shipped from the factory with the Electronic Control Diagnostic Harness Assembly unplugged. To avoid unauthorized manual programming or vending, perform the following steps. The factory mounted coin meter case does not include the service door lock, coin drawer, coin drawer lock or keys. These parts must be ordered (at extra cost) according to the purchaser’s requirements direct from the manufacturer of your choice.
Installation Additional Washer Security (Coin Models Only) Located on the service door of the washer is a flat Phillips head screw. During shipment, this screw is used to attach the service door to the meter case. For additional security, this screw can be reinstalled inside the control hood of your washer. Refer to instructions below for installation. Tamper-resistant screws also can be installed for additional security.
Operation Operation Instructions for MDC Washers Step 2: Load Laundry IMPORTANT: Prior to first wash, use an allpurpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washer. Load dry clothes loosely into washtub – DO NOT overload! (10 kg [22 lbs.] maximum dry clothes load) When washing large items such as shag rugs and bedspreads, add several small items to balance wash load.
Operation Step 4: Set Fabric Selector and Wash Temperature Step 6: Start Washer Push touchpad for NORMAL/HOT, NORMAL/ WARM, PERM PRESS/WARM or DELICATES/ COLD. Light indicates selection. After vend price has been satisfied, push the START pad. LID MUST BE CLOSED TO START WASHER. FLW1920N FLW1920N FLW1923N Figure 18 Figure 20 Step 5: Insert Money Indicator Lights Insert coin(s) into coin slot. Check pricing as seen on digital display.
Maintenance User-Maintenance Instructions Reinstallation of Shipping Materials Cold Weather Care Shipping Brace If the washer is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate the washer until it has had a chance to warm up. The shipping brace in the lid opening should be saved and reinstalled whenever the washer is moved.
Troubleshooting Try these troubleshooting tips before making a service call. They may save you time and money. Washer Symptom Won’t Fill Possible Cause/Solution Make sure lid is closed. Make sure power cord is plugged all the way into the electrical outlet. Make sure hot and cold water faucets are turned on. Make sure that the fill hoses are not kinked or twisted. Place coin(s) in drop or card in reader. Make sure that the controls are properly set.
Troubleshooting Washer Symptom Possible Cause/Solution Won’t Drain Make sure drain hose is not kinked or twisted. Make sure drain hose is not clogged. Make sure drain receptacle is not clogged. Refer to the Installation section to make sure that the drain hose has been properly installed. Water Leaks Check that fill hoses are properly installed on the faucets and the washer’s water mixing valve. Replace the fill hoses every five years. Make sure drain receptacle is not clogged.
Contact Information If service is required, contact the nearest Factory Authorized Service Center. If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: (920) 748-3121 When calling or writing about your unit, PLEASE GIVE THE MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the nameplate.
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) 1 CHECK 2 TLW2098N 6 • Wipe Out Inside of Washtub. • Connect Fill Hoses. • Position and Level the Washer. CHECK TLW2098N CHECK 3 5 • Remove the Shipping Brace and Shipping Plug. TLW2099N 7 COLD HOT D255I D255I W316IE0A W316IE0A • Plug In the Washer. CHECK TLW2099N LEVEL D254IE0A D254IE0A • Add Water to the Washer.
