Specifications
Installation
31
F8429301 (EN)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Machine Foundation and Pad
Installation
A concrete pad may be constructed to elevate a
machine. Care must be exercised in the design of the
pad due to the force exerted by the machine during
extract. This concrete pad, recommended not to
exceed 8 inches (203 mm) above existing floor, must
be placed, reinforced with rebar and tied to the
existing floor. Refer to Table 2 and Figure 18 through
Figure 35 for multiple machine installations.
Table 2
IMPORTANT: Do NOT install a pad on top of the
existing floor. The foundation and pad must be
constructed and tied together as one piece.
If the existing floor is not reinforced concrete at least
of minimum thickness (depending on model), an
elevated pad is desired or multiple machines are to be
installed, the following steps must be performed (refer
to Figures 18 through 35):
1. Cut a hole larger on all sides than the machine
base through the existing floor, refer to Table 2 .
2. Excavate to a depth as indicated in Table 2 from
the top of the existing floor.
3. If installing a foundation with elevated pad,
prepare a form for the above-ground portion of
the foundation. Verify that the top of the
foundation is level. The height of the foundation
pad must not exceed 8 inches (203 mm) above
the existing floor.
4. Backfill with clean fill dirt.
5. Compact backfill, making sure to allow for
correct concrete thickness.
Model 20 30 40 60 80-100 125
Minimum
Foundation
Thickness
F-speed
4 in.
(102 mm)
4 in.
(102 mm)
4 in.
(102 mm)
4 in.
(102 mm)
6 in.
(152 mm)
N/A
V-sp ee d 6 in .
(152 mm)
6 in.
(152 mm)
9 in.
(229 mm)
12 in.
(305 mm)
Minimum
Excavation
Depth
F-speed
8 in.
(203 mm)
8 in.
(203 mm)
8 in.
(203 mm)
8 in.
(203 mm)
12 in.
(305 mm)
N/A
V-sp ee d 12 i n.
(305 mm)
12 in.
(305 mm)
15 in.
(381 mm)
18 in.
(457 mm)
Minimum Pad Size
Single machine
(w x d)
31.4 in. x 34.8 in.
(798 mm x
884 mm)
34.4 in. x 39.5 in.
(874 mm x
1003 mm)
36.5 in. x 43.5 in.
(927 mm x
1105 mm)
44.8 in. x 50.6 in.
(1139 mm x
1285 mm)
57.5 in. x 49.2 in.
(1461 mm x
1250 mm)
72 in. x 72 in.
(1828 mm x
1828 mm)
Two machines,
Side-by-side
57.4 in. x 34.8 in.
(1458 mm x
884 mm)
67.4 in. x 39.5 in.
(1712 mm x
1003 mm)
67.1 in. x 43.5 in.
(1704 mm x
1105 mm)
78.9 in. x 50.6 in.
(2004 mm x
1285 mm)
93.0 in. x 49.2 in.
(2362 mm x
1250 mm)
133 in. x 72 in.
(3378 mm x
1828 mm)
Two machines,
Back-to-back
31.4 in. x 85.7 in.
(798 mm x
2177 mm)
34.4 in. x 95 in.
(874 mm x
2413 mm)
36.5 in. x 103.1 in.
(927 mm x
2619 mm)
44.8 in. x 113.2 in.
(1138 mm x
2875 mm)
51.5 in. x 119.9 in.
(1308 mm x
3046 mm)
72 in. x 156 in.
(1828 mm x
3962 mm)
NOTE: Inside and outside mounting only available on 80 and 100 pound models.
N/A = Not Applicable