Specifications

ManualsBrandsAlliance Laundry Systems ManualsDomestic AppliancesGA2210*A1102

WARNING

Electrical shock hazard will result in death or seri-

ous injury. Disconnect electric power and wait three

(3) minutes before servicing.

W784

WARNING

Dangerous voltages are present inside the machine.

Only qualified personnel should attempt adjust-

ments and troubleshooting. Disconnect power from

the machine before removing any cover and guards,

and before attempting any service procedures.

W736

WARNING

Hazardous Voltage. Can cause shock, burn or death.

Verify that a ground wire from a proven earth ground

is connected to the lug near the input power block

on this machine.

W360

Electrical connections are made at the rear of the machine. The

machine must be connected to the proper electrical supply shown

on the identification plate attached to the rear of the machine, us-

ing copper conductors only.

IMPORTANT: Alliance Laundry Systems warranty does

not cover components that fail as a result of improper

input voltage.

Make sure the correct transformer jumper [208 Volt or 240 Volt]

is in place. Refer to the “optional” Electrical Service Conversion

label located on the back of the machine near the electrical serv-

ice input for machine electrical requirements. Refer to Figure 18

and Figure 19 .

VAC: 200-208

PHASE: *

AMPS: *

* As indicated on

original serial plate

200-208 VAC CONVERSION

50Hz

Operation

50Hz CONVERSION

1. Refer to the Control Transformer area on

the Control Option Diagram.

2. Remove the "240V" Transfor mer Jumper in

the control box.

3. Replace with "208V" Transformer Jumper

found in the diagram pac k.

4. Sign off below.

1. Refer to the Control Option Diagram.

2. Remove the wire from the 60Hz tap on drain

valve(s).

3. Connect the wire to the 50Hz Tap on all

drain valves.

4. Sign off below.

(SIGN)

(DATE)

F8099701R1

200-208VAC

Operation

Transformer Jumper

208V

This unit may be field converted

by a QUALIFIED Electrician to

the following 200-208 Volts

and/or 50 Hertz.

PRIOR TO CONNECTING

ELECTRICAL SERVICE,

COMPLETE THE FOLLOWING

OPTIONAL ELECTRICAL SERVICE

CONNECTION BASED ON

AVAILABILITY

WIRES & GROUND: *

REC'D BREAKER: *

Drain Valve(s)

50Hz

60Hz N

Connection

for 50Hz

Operation Only

PHM740N_SVG

O, Q, X and Y–voltage Models

Figure 18

PHM756N_SVG

N, P and R–voltage Models

Figure 19

On V-speed models, the AC inverter drive requires a clean power

supply free from voltage spikes and surges. Use a voltage moni-

tor to check incoming power.

The following conditions require corrective action, contact the lo-

cal utility to adjust the voltage.

• If the local utility cannot adjust the input voltage, install a

buckboost transformer to lower the input voltage.

• Input voltage is above 240V or 480V, phase to ground voltage

exceeds 125% of normal line to line voltage, or 240V open

delta configuration (stinger leg).

Contact a qualified electrical maintenance person for assistance.

On V-speed models, the AC drive provides thermal overload pro-

tection for the drive motor. However, a separate three-phase cir-

cuit breaker must be installed for complete electrical overload

protection. This prevents damage to the motor by disconnecting

all legs if one should be lost accidentally. Check the nameplate

on the back of the machine for recommended circuit breaker re-

quirements size.

IMPORTANT: Do NOT use fuses in place of a circuit

breaker.

CAUTION

Do not use a phase adder on any variable-speed ma-

chine.

SW037

The machine should be connected to an individual branch circuit

not shared with lighting or other equipment.

The connection should be shielded in a liquid-tight or approved

flexible conduit with proper conductors of correct size installed

in accordance with applicable codes. The connection must be

made by a qualified electrician using the wiring diagram provi-

ded with the machine, or according to accepted European stand-

ards.

Refer to nameplate for recommended circuit breaker size and de-

termine wire size based on local code requirements.

Refer to nameplate for recommended wire sizes for runs up to 50

feet [15.24 meters]. Use next larger size for runs of 50 to 100 feet

[15.24 to 30.48 meters]. Use 2 sizes larger for runs greater than

100 feet [30.48 meters].

Specifications and Dimensions