Installation Washer-Extractors Cabinet Freestanding Refer to Page 2 for Model Identification H H CFD14C 18 and 30 Models CFD14C CFD16C 33 and 40 Models Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 9001909R4 www.comlaundry.
Table of Contents Introduction......................................................................................... Model Identification ............................................................................. Nameplate Location.............................................................................. Replacement Parts ................................................................................ Customer Service................................................................................
Introduction Model Identification Information in this manual is applicable to these models: 2 18 NX18BVPA6 NX18BVPA7 NX18BVQA6 NX18BVQA7 NX18BVXA6 NX18BVXA7 NX18BVXM6 NX18BVXM7 SX18BVPA7 SX18BVQA7 SX18BVXA7 SX18BVXM7 30 NX30BVPA6 NX30BVPA7 NX30BVQA6 NX30BVQA7 NX30BVXA6 NX30BVXA7 NX30BVXM6 NX30BVXM7 SX30BVPA7 SX30BVQA7 SX30BVXA7 SX30BVXM7 33 SX33BVPA7 SX33BVQA7 SX33BVXA7 SX33BVXM7 40 SX40BVPA7 SX40BVQA7 SX40BVXA7 SX40BVXM7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 900
Introduction Nameplate Location The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1 and Figure 2.
Introduction Model Number Familiarization Guide Sample Model Number: NX18BVXM60001 NX Model Number Prefix 18 Washer-Extractor Capacity (pounds dry weight of laundry) B Type of Electrical Control V Washer-Extractor Speed Capability (V = Variable-Speed) X Voltage Code M6 0001 Design Series (M=Domestic, A=International) Option Identification (varies from machine to machine) NX18BVXM60001 6 50 60 18 15 2/3+PE 8 1 1000 EXAMPLE OF NAMEPLATE CFD22N CFD22N Figure 2 4 © Copyright, Alliance Laund
Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.
Safety Information 9. Do not install or store the washer where it will be exposed to water and/or weather. 10. Do not tamper with the controls. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. 12.
Safety Information WARNING CAUTION This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty. SW004 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided.
Safety Information Operator Safety Do not bypass any safety devices in the machine. WARNING WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. SW012 To ensure the safety of machine operators, the following maintenance checks must be performed daily: Never operate the machine with a bypassed or disconnected balance system.
Specifications and Dimensions General Specifications Model 18 30 33 40 Overall width 26 in. (660 mm) 30.7 in. (780 mm) 30.7 in. (780 mm) 30.7 in. (780 mm) Overall height 40.9 in. (1038 mm) 47.3 in. (1202 mm) 54.15 in. (1376 mm) 54.15 in. (1376 mm) Overall depth 29.1 in. (739 mm) 33.1 in. (842 mm) 33.07 in. (840 mm) 37.01 in. (940 mm) Net weight 465.2 lb. (211 kg) 716.5 lb. (325 kg) 811.30 lb. (368 kg) 862.01 lb. (391 kg) Shipping weight 513.7 lb. (233 kg) 782.6 lb. (355 kg) 844.
Specifications and Dimensions General Specifications Model 18 30 33 40 1 1 1 1 1 HP (0.75 kW) 2 HP (1.5 kW) 2.95 HP (2.2 kW) 2.95 HP (2.2 kW) 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 85 RPM 85 RPM 85 RPM 85 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM 0.03-0.74 Gs 0.04-0.91 Gs 0.37-0.94 Gs 0.37-0.
Specifications and Dimensions 8.7 in. (220 mm) H 40.9 in. (1038 mm) 39.8 in. (1011 mm) 14.4 in. (365 mm) 20.9 in. (530 mm) 2.6 in. (65 mm) 2.6 in. (65 mm) 26 in. (660 mm) 26.3 in. (670 mm) 2.7 in. (69 mm) 9.1 in. (231 mm) 6 in. (153 mm) 3 in. (75 mm) 1 28.6 in. (727 mm) 7.2 in. (184 mm) 5.5 in. (139 mm) 8 2 33.2 in. (843 mm) 3 4 7 6 31.9 in. (809 mm) 7 in. (180 mm) 27.7 in. (633 mm) 5 26 in. (660 mm) 2.8 in. (70 mm) 18 MODEL CFD519N CFD519N 1 2 3 4 Hot Water Connections .75 in.
Specifications and Dimensions 3.5 in. (88 mm) 8.7 in. (220 mm) H 474 in. (1202 mm) 46.3 in. (1175 mm) 18.7 in. (475 mm) 25.5 in. (648 mm) 2.6 in. (66 mm) 2.6 in. (66 mm) 30.7 in. (780 mm) 29.9 in. (760 mm) 3.2 in. (82 mm) 13.1 in. (332 mm) 10.5 in. (267 mm) 8 in. (202 mm) 1 2 32.1 in. (816 mm) 7.9 in. (200 mm) 6.1 in. (155 mm) 8 3 4 7 36.4 in. (924 mm) 5 1.4 in. (35 mm) 38 in. (964 mm) 7.9 in. (200 mm) 33.5 in. (849 mm) 6 2.8 in.
Specifications and Dimensions 3.47 in. (88 mm) 8.66 in. (220 mm) 18.58 in. (472 mm) 54.15 in. (1376 mm) 53.07 in. (1348 mm) H 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) 1.34 in. (34 mm) 3.41 in. (86.5 mm) CFD537N CFD540N 13.05 in. (332 mm) 10.49 in. (267 mm) 7.93 in. (202 mm) 4.13 in. (105 mm) 1 2 4 26.18 in. (665 mm) 28.86 in. (733 mm) 29.65 in. (753 mm) 1.34 in. (34 mm) CFD538N CFD538N 3 5 6 7 1.38 in. (35 mm) 4.3 in. (109 mm) 7.29 in. (185 mm) 39.96 in.
Specifications and Dimensions 3.47 in. (88 mm) 8.66 in. (220 mm) 18.58 in. (472 mm) 54.15 in. (1376 mm) 53.07 in. (1348 mm) H 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) 1.34 in. (34 mm) 3.41 in. (86.5 mm) CFD537N CFD540N 13.05 in. (332 mm) 10.49 in. (267 mm) 7.93 in. (202 mm) 4.13 in. (105 mm) 1 2 4 30.12 in. (765 mm) 32.8 in. (833 mm) 33.58 in. (853 mm) 1.34 in. (34 mm) CFD538N CFD538N 3 5 6 7 1.38 in. (35 mm) 4.3 in. (109 mm) 7.29 in. (185 mm) 39.96 in.
Installation Dimensional Clearances Machine Foundation Table 1 shows recommended minimum clearances on all sides of the washer-extractor. Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract. Recommended Minimum Clearances Model 18 30 33 40 Minimum rear 24 in. 24 in. 24 in. 24 in.
Installation Mechanical Installation Frame Dimensions and Mounting Bolt Location 1.18 in. (30 mm) 25.59 in. (690 mm) 23.23 in. (590 mm) 0.74 in. (18 mm) 1.18 in. (30 mm) 2.26 in. (65 mm) 20.87 in. (530 mm) 2.26 in. (65 mm) 25.98 in. (660 mm) 18 MODEL CFD67N Figure 7 IMPORTANT: Drawing is not to scale.
Installation 1.44 in. (36.5 mm) 29.06 in. (738 mm) 26.18 in. (665 mm) 0.71 in. (18 mm) 1.44 in. (36.5 mm) 25.51 in. (648 mm) 2.60 in. (66 mm) 2.60 in. (66 mm) 30.71 in. (780 mm) 30 MODEL CFD68N Figure 8 IMPORTANT: Drawing is not to scale.
Installation 1.34 in. (34 mm) 28.86 in. (733 mm) 26.18 in. (665 mm) .87 in. (22 mm) 1.34 in. (34 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) CFD541N 33 MODEL CFD541N Figure 9 IMPORTANT: Drawing is not to scale.
Installation 1.34 in. (34 mm) 328 in. (833 mm) 30.12 in. (765 mm) .87 in. (22 mm) 1.34 in. (34 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) CFD542N 30.71 in. (780 mm) 40 MODEL CFD542N Figure 10 IMPORTANT: Drawing is not to scale.
Installation Mounting Bolt Installation (If Required) 4. To level machine, fill the spaces between the machine base and floor with machinery grout. Grout completely under all frame members. Remove front and rear panels to gain access to all frame members. Force grout under the machine base until all voids are filled. 1 2 5. Remove the spacers carefully, allowing the machine to settle into the wet grout. 3 6. Position washers and locknuts on machinery anchor bolts and fingertighten to machine base. 7.
Installation Removing the Transport Block 4. For 18 and 30 models, remove the panel braces. Refer to Figure 13. WARNING The machine must never be activated before removing the transport block. W618 To prevent damage during transportation, machine has been equipped with a transport block. To remove, proceed as follows: 1. Place machine on level ground. 2. Remove service panels and back panel. 3. For 18 and 30 models, at rear of machine, lift at bottom of motor and remove transport block if present.
Installation Drain Connection Figure 15 A drain system of adequate capacity is essential to washer-extractor performance. Ideally, the water should empty through a vented pipe directly into a sump or floor drain. Figure 15 shows drain line and drain trough configurations. REAR OF MACHINE A flexible connection must be made to a vented or air gap drain system to prevent an air lock and to prevent siphoning. If proper drain size is not available or practical, a surge tank is required.
Installation Water Connection Pressure of 30-85 psi (2-5.86 bar) provides best performance. Although the washer-extractor will function at lower pressures, increased fill times will occur with some loss of supply flushing. WARNING To avoid personal injury, recommended inlet water temperature should be no higher than 125° Fahrenheit (51° Celsius). Suitable air cushions should be installed in supply lines to prevent “hammering.
Installation Electrical Installation IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine. IMPORTANT: Alliance Laundry Systems warranty does not cover compounds that fail as a result of improper input voltage. WARNING Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to working in and around AC inverter drive. W359 WARNING Hazardous Voltage.
Installation Machine with Electric Heating 380-415V 3AC + N 200-240V 3AC 380-415V 3 phase (3AC + N) has to be connected to the connectors “L1, L2, L3”, the blue neutral to the “N” connector. Refer to Figure 16. 200-240V 3 phase (3AC) should be connected to the connectors “L1, L2, L3”. Refer to Figure 16. The green/yellow grounding clamp has to be connected to the grounding wire “PE”. The green/yellow grounding clamp has to be connected to the grounding wire “PE”.
Installation Out-of-Balance Switch 1 2 CFS501N 1 2 Window Probe Figure 17 The out-of-balance switch is mounted on the upper right side on the back of the control panel. There is a window around the probe of the switch that is mounted on the movable part of the machine. When the machine goes out of balance by overloading or uneven distribution of the linen, the out-of-balance switch will interrupt this action to prevent damage to the machine.
Installation Control Function Test b. Close the door without locking it and attempt to start the washer. The washer should not start with the door unlocked. The washer-extractor should be cleaned after the installation is complete. A function test should then be executed on the unloaded machine: c. Close and lock the door and start a cycle. Attempt to open the door while the cycle is in progress. The door should not open. 1.
