Cabinet Freestanding Refer to Page 7 for Model Identification CFD28C_SVG Operation/Maintenance Washer-Extractors CFD29C_SVG Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.
Table of Contents Safety Information..................................................................................4 Explanation of Safety Messages....................................................................... 4 Important Safety Instructions........................................................................... 4 Safety Decals................................................................................................. 5 Operator Safety.....................................................
Safety Information Safety Information Explanation of Safety Messages • Precautionary statements [“DANGER,” “WARNING,” and “CAUTION”], followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. • DANGER • Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
Safety Information • • • • • • • • • • • • • warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times [preferably in a locked cabinet]. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. Always follow the fabric care instructions supplied by the textile manufacturer. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin.
Safety Information WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. SW012 The following maintenance checks must be performed daily: 1. Verify that all warning labels are present and legible, replace as necessary. 2. Check door interlock before starting operation of the machine: a. Attempt to start the machine with the door open. The machine should not start. b. Close the door without locking it and start the machine.
Introduction Introduction Model Identification Information in this manual is applicable to these models: HHF455 HXG100 HXY030 SXA195 SXU165 UX35 UXN305 HHF575 HXG165 HXY035 SXA235 SXU195 UX45 UXR018 HHF730 HXG235 HXY045 SXA305 SXU235 UX55 UXR025 HHF900 HXG305 HXY055 SXE018 SXU305 UX75 UXR035 HX18 HXN075 HXY075 SXE025 SXW075 UX100 UXR055 HX25 HXN100 HXZ075 SXE035 SXW100 UX135 UXR075 HX30 HXN135 HXZ100 SXE055 SXW165 UX165 UXU075 HX35 HXN165 HXZ165 SXE075 S
Introduction Nameplate Location The nameplate is located on the back of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1. CFD603N_SVG 1. Nameplate Figure 1 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.
Operation Operation WE-8 Control WE-8 Control Panel 3 2 5 1 4 M172_SVG 1. 2. 3. 4. 5. Keypad Display Emergency Stop Button Key Switch Serial Port Figure 2 Load the Machine 1. For 18 - 75 pound models: Pull the door handle towards you to open the door. Some models may have a door handle with a button that must be pressed. 2. For 100 - 200 pound models: Push on the doorlock system to open the door. 3. Load the drum to the specified capacity. 4.
Operation 2. 3. 4. 5. 6. a. Press and hold the Start keypad for at least 3 seconds. Enter the number of hours to delay start. Press the Start keypad. Enter the number of minutes to delay start. Close the door. Press the Start keypad. Chemical Hold Feature Chemical supply injection can be paused. Refer to section Setup of the Chemical Hold Feature in Programming manual. Stop the Machine The delayed start time is shown in the display.
Operation Enter to retry Clear to stop Enter to retry Clear to stop Figure 9 If Enter (START) key is pressed during fill alarm, condition will end and step will start over. If programmed water level is not reached within programmed step time, fill alarm will occur again Refer to Figure 9 . Done Cycle CC Figure 13 If Enter (START) key is pressed, drain alarm ends, and drain step starts over at beginning. If machine has not emptied when drain step time expires, alarm occurs again.
Operation • • Wiring to electrical or steam heating relay has failed. Electrical heating elements or steam valve is broken. NOTE: If the cycle aborted, it may be due to a temperature sensor error. Possible Faults: • • Broken RPM Sensor. RPM Sensor dislocated (distance from RPM Sensor to pulley is greater than 2 mm). Broken V-belt. Wiring disconnected. Rotation Sensor Error • • The control did not sense any pulses or the control sensed wrong pulses from the RPM Sensor.
Operation B-Series Control Panel 95C 95C 60C 60C 40C 40C 30C < < CHM488R_SVG 1. Cycle 1 2. Cycle 2 3. Cycle 3 4. Cycle 4/Up Edit 5. Cycle 5 6. Cycle 6 7. Cycle 7 8. Cycle 8/Down Edit 9. START (enter) Keypad 10. LED (not in use) 11. Door Step LED 12. Spin Step LED 13. Rinse Step LED 14. Add Bleach LED 15. Decimal for Pricing 16.
Operation 3 CHM2229N_SVG CHM2268N_SVG 3. Liquid Bleach Figure 19 4. Add supplies to the supply dispenser. Refer to Table 1 . a. Detergent: • Liquid - Compartment 1 (prewash) + Compartment 3 • Powder - Compartment 1 (prewash) + Compartment 2 b. Bleach: • Liquid - Compartment 3 • Powder - Compartment 2 c. Softener: • Liquid - Compartment 4 4 CHM2230N_SVG 4. Powder Bleach c. SOFTENER a. DETERGENT 1 5 CHM2231N_SVG CHM2228N_SVG 5. Liquid Softener 1. Liquid Detergent Table 1 5.
Operation DRY2317N_SVG Figure 21 7. Start the cycle by pressing the START keypad. Refer to Figure 22 . 95C 95C 60C 60C 40C 40C 30C < < CFD736N_SVG Figure 22 The cycle will continue until its completion. When the cycle is complete, the door is unlocked.
Tilting Option Tilting Option The operator controls the tilting and basket rotation using a pendant control. The pendant control has a safety button, which the operator must press and hold while pressing the other buttons on the pendant control, which include tilt forward (up), tilt backward (down), right basket rotation (forward) and left backet rotation (reverse). Operation When the cycle has finished, the control unlocks the door. The tilt screen is shown in the control's display. Refer to Figure 23 .
Maintenance Maintenance WARNING WARNING Sharp edges can cause personal injury. Wear safety glasses and gloves, use proper tools and provide lighting when handling sheet metal parts. To reduce the risk of electrical shock, serious injury or death, disconnect the electrical power to washer-extractor before examining the wiring. W366R1 IMPORTANT: Replace all panels that are removed to perform service and maintenance procedures.
Maintenance 3. On machines equipped with an automatic chemical supply system, check chemical connections by inspecting all connections and chemical hoses for leaks or cracks. IMPORTANT: Chemical leaks can quickly cause permanent damage to the machine components and structure. Belt Tension Product Family Monthly NOTE: Disconnect power to the machine at its source before performing the monthly maintenance procedures. 1. Check belt(s) require replacement or adjustment.
Maintenance 7. Clean all electronic boards of moisture and dust with canned air. 8. Verify the insulation is intact on all external wires and that all connections are secure. If bare wire is evident, call a service technician. 9. Clean inverter drive cooling fan blades [where applicable]. 1 Annually CFD902N_SVG For 75, 90, 305 and 400 models only, replace the machine’s automatic lubricator. 1.
