Installation Frontload Washers Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com. FLW1522C FLW1522C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Part No.
Table of Contents Replacement Parts .............................................................................. 2 Installation........................................................................................... 3 Dimensions and Specifications............................................................. 3 Before You Start ................................................................................... 4 Tools ....................................................................................
Replacement Parts If replacement parts are required, contact the source from which you purchased your washer, or contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Phone: (920) 748-3950 for the name and address of the nearest authorized parts distributor.
Installation Dimensions and Specifications 29.6 in. (75.1 cm) 41.2 in. (104.6 cm) 14.3 in. (36.3 cm) 31.1 in. (79 cm) 17.5 in. (44.8 cm) 28 in. (71.1 cm) 2 in. (5.1 cm) 26.9 in. (68.3 cm) FLW2092N MODELS WITH OLD STYLE DOOR FLW2092N 28 in. (71.1 cm) 29.6 in. (75.1 cm) 14.3 in. (36.3 cm) 31.1 in. (79 cm) 41.2 in. (104.6 cm) 18.7 in. (47.5 cm) 2 in. (5.1 cm) 26.9 in. (68.
Installation Before You Start Water Tools Washer needs two standard 3/4 in. (19.1 mm) water supply faucets with a pressure between 20 and 120 pounds per square inch (138 to 827 kPa). For more detailed information refer to section on Water Supply Requirements. For most installations, the basic tools you will need are: 2 1 3 Accessories Bag 4 An accessories bag has been shipped inside your washer. It includes: • Two fill hoses with washers and filter screens. Refer to step 2 of Installation.
Installation Installing the Washer Step 2: Connect Fill Hoses NOTE: If the washer is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until the washer has had a chance to warm up. NOTE: Refer to section on Water Supply Requirements before connecting fill hoses. Step 1: Position Washer Near Installation Area IMPORTANT: Install dryer before washer. This allows room for attaching exhaust duct.
Installation IMPORTANT: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to. All hoses should be checked on a yearly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years.
Installation In-the-Wall Installation For installations of this type, the drain hose MUST be secured to one of the fill hoses using the beaded tiedown strap from accessories bag. NOTE: End of drain hose must not be below 24 in. (61 cm). 1 1 2 3 FLW1959N FLW1959N 1 2 24 in. to 36 in. (91.44 cm recommended height) Standpipe 2 in. (5.08 cm) or 1-1/2 in.
Installation Laundry Tub Installation Step 4: Position and Level the Washer For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use. Use the beaded tie-down strap (supplied in accessories bag) to secure hose. 1 WARNING Washers elevated above floor level must be anchored to that elevated surface, base or platform.
Installation Remove rubber feet from accessories bag and place on all four leveling legs. Step 5: Remove the Shock Sleeves and Shipping Brace Verify that unit doesn’t rock. Remove front access panel by removing the two screws. 3 2 Remove label from front side of front access panel and place on backside of front access panel. 1 NOTE: The shipping brace, bolts, lockwashers and shock sleeves should be saved and MUST be reinstalled whenever the unit is moved more than four feet.
Installation Step 6: Wipe Out Inside of Washer Drum Before using the washer for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside the drum. Supply Injection System Number of liquid supply connections (1–Detergent and 2–Softener) 2 Liquid supply connection size, in. (mm) 3/8 (9.52) or 1/4 (6.
Installation A junction box on the rear panel houses a terminal strip which furnishes supply output signals for the supply injection pumps.These are dry contacts. Voltage needs to be supplied. Refer to Figure 14 for the injection interface label. Step 8: Plug In the Washer Refer to section on Electrical Requirements and connect the washer to an electrical power source.
Installation Electrical Requirements 1 (120 Volt, 60 Hertz with 3-Prong Grounding Plug) NOTE: The wiring diagram is located behind the control panel, inside the control cabinet. WARNING 2 4 H336I 3 H336I 1 2 3 4 Shock Sleeves Motor Mount Bolts and Lockwashers Hooked End of Shipping Brace Figure 16 Refer to step 5 for proper procedures whenever the unit is moved.
Installation 3 1 WARNING 2 To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electric power source. 120 ± 12 V.A.C. 0 V.A.C. W082 Grounding Instructions 5 The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
Installation Water Supply Requirements Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time.
Installation Information for Handy Reference Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Date Purchased Model Number Serial Number Dealer’s Name Dealer’s Address Phone Number Service Agency Service Agency Address Phone Number NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate.
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) 1 5 • Position Washer Near Installation Area. • Remove the Shock Sleeves and Shipping Brace. H336I H336I CHECK CHECK FLW702N FLW702N 2 6 • Connect Fill Hoses. • Wipe Out Inside of Washer Drum. W520I W520I FLW2049N FLW2049N CHECK 3 CHECK 7 • Connect Drain Hose to Drain Receptacle. (Supply Injection Models Only) • Connect External Supplies to Washer.
