MODEL: LS5T-52A WARNING! To Reduce The Risk Of Injury, User Must Read And Understand Instruction Manual. www.jdna.
SAFETY WARNINGS & CAUTIONS SAFETY WARNINGS & INSTRUCTIONS z UNDERSTAND YOUR LOG SPLITTER Read and understand the owner’s manual and labels affixed to the log splitter. Learn its application and limitations as well as the specific potential hazards peculiar to it. z DRUGS, ALCOHOL AND MEDICATION Do not operate the log splitter while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly. z AVOID DANGEROUS CONDITIONS Put the log splitter on a 23.6 - 29.
z EXTENSION CORDS Improper use of extension cords may cause inefficient operation of the log splitter which can result in overheating. Be sure the extension cord is no longer than 33feet and its section is no less than 2.5mm2 to allow sufficient current flow to the motor. Avoid use of free and inadequately insulated connections. Connections must be made with protected material suitable for outdoor use.
z PROTECT YOUR HANDS Keep you hands away from splits and cracks which open in the log; They may close suddenly and crush or amputate your hands. Do not remove jammed logs with you hands. z DON’T FORCE TOOL It will do a better and safer job at its design rate. Never try to split logs larger than those indicated in the specifications table. This could be dangerous and may damage the machine. Don’t use log splitter for a purpose for which it was not intended.
APPLICATION CONDITIONS This log splitter is a home use model. It is designed for operating under ambient temperatures between +66.6oF and 129.6oF and for installation at altitudes no more than 3300feet above M.S.L. The surrounding humidity should less than 50% at 129.6oF. It can be stored or transported under ambient temperatures between -102.6oF and 156.6oF.
SET UP AND PREPARATION FOR OPERATION 1. Bolt the Support Leg to the Log Splitter, lift the log splitter by the handles at both ends and place it on a 23.6 - 29.5in high, stable, flat and level work surface. 2. Familiarize yourself with the controls and features of this log splitter in the illustrations. 1. Log Pusher 2. Work Table 3. Wedge 4. Lift Handle 5. Support Leg 6. Log Retaining Plates 7. Switch 8. Motor 9. Pushbutton Box 10. Wheels for Minor Moving ONLY. 11. Hydraulic Control Lever 12.
15. Max Pressure Limiting Screw DO NOT ADJUST THE MAX PRESSURE LIMITING SCREW ! Max pressure was set before the log splitter ex work and the max pressure limiting screw is sealed with glue to ensure the log splitter works under pressure no more than 5 tons. The setting was done by qualified mechanic with professional instruments. Unauthorized resetting will cause the hydraulic pump fail to output enough splitting pressure or RESULT IN 15 SERIOUS INJURY AS WELL AS DAMAGE TO THE MACHINE .
LOG SPLITTER OPERATION This log splitter is equipped with “ZHB” control system that requires to be operated by both hands of the user – Left hand controls the hydraulic control lever while right hand controls the pushbutton switch. The log splitter will freeze upon absence of either hand. Only after both hands release the controls, the log pusher starts to return backward to the starting position. Trigger type lock-out device is adopted to avoid accidental Hydraulic Control Lever pushdown.
Break log in the direction of its growing grain. Do not place log across the log splitter for splitting. It may be dangerous and may seriously damage the machine. Do not attempt to split 2 pieces of logs at the same time. One of them may fly up and hit you. FREEING A JAMMED LOG z Release both controls. z After the log pusher moves back and completely stops at its starting position, insert a wedge wood under the jammed log.
REPLACING HYDRAULIC OIL Replace the Hydraulic oil in the log splitter after every 150 hours of use. Take following steps to replace it. z Make sure all moving parts stops and the log splitter is unplugged. z Unscrew Oil Drain Bolt with Dipstick to remove it. z Turn the log splitter on the Support Leg side over an 4 liters capacity container to drain the hydraulic oil off. z Turn the log splitter on the the motor side.
SHARPENING WEDGE After using the log splitters for some time, sharpen the wedge of the log splitter using a fine-toothed file and smooth any burrs or crushed area along the cutting edge.
No Name in English quantity (pcs) No Name in English quantity (pcs) SP-LS05-01-WG Oil cylinder 1 SP-LS05-29-WG Small shaft inner sleeve 1 SP-LS05-02-WG ST type ring55 1 SP-LS05-30-WG small spring 1 SP-LS05-03-WG Piston 1 SP-LS05-31-WG Gasket 16 1 SP-LS05-04-WG Gasket ring 23.6x3.55 1 SP-LS05-32-WG plug M16X1.
No Name in English quantity (pcs) No Name in English quantity (pcs) SP-LS05-57-WG flat key 1 SP-LS05-84-WG seal gasket 1 SP-LS05-58-WG Gear spindle 1 SP-LS05-85-WG seal gasket 1 SP-LS05-59-WG Gear 2 SP-LS05-86-WG Gasket 5.8X1.3 1 SP-LS05-60-WG Middle clapboard 1 SP-LS05-87-WG washer 1 SP-LS05-61-WG outer hexagon bolt M6X40 6 SP-LS05-88-WG seal gasket 1 SP-LS05-62-WG Ring 46.2X1.
Limited Warranty ALL-POWER R ALLPOWER R warrants to the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty are free from defects in material and workmanship for one year from the date of purchase. All products covered by this limited warranty which are used in commercial applications (i.e.
Limited Warranty (cont’d) THIS WARRANTY DOES NOT COVER: Merchandise sold as reconditioned, used as rental equipment, or floor or display models.
