WOOD CHIPPER User Manual SAFETY AND OPERATION INSTRUCTIONS APWC420 IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Table of Contents Table of Contents PART I: General Safety Rules............................................................................................................2 PART II: Familiar with the Wood Chipper......................................................................................... 8 PART III: Operating the Wood Chipper..............................................................................................9 PART IV: Maintaining the Wood Chipper.....................................
Part I: General Safety Rules PART I: General Safety Rules Safety Labels Found on Your Unit 2
Part I: General Safety Rules Should make sure the emergency stop switch is available before every use. Or may result in serious injury even death. WARNING Read this Safety & Operating Instructions manual before you use the Wood Chipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine. Propose CAUTION This machine is designed solely to chip wood and must not be used for any other purpose.
Part VI: Troubleshooting and Parts Lis Before using the wood chipper NOTICE A． Operators must be fully trained before using this machine. B．User Manual is read and understood. C． Machine is positioned on level ground, all guards are fitted and in good condition. D． Blades are in good condition and secure. All blades are sharpened or replaced in sets. E．All fasteners are checked for tightness. F． Only WOODEN materials free of nails etc. are fed into the machine.
Part I: General Safety Rules Safety for Children and Pets WARNING Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the machine and the chipping activity. Never assume that children will remain where you last saw them. Always follow these precautions: A. Keep children and pets at least 50 feet from the working area and ensure they are under the watchful care of a responsible adult. B.
Part VI: Troubleshooting and Parts Lis required, see your authorized dealer for engine governor adjustments. I. Keep combustible substances away from the engine when it is hot. J. Never cover the machine while the muffler is still hot. K. Do not operate the engine with the air cleaner or the carburetor air intake cover removed. Removal of such parts could create a fire hazard. Do not use flammable solutions to clean the air filter. L.
Part I: General Safety Rules N. Use the machine only in daylight. O. Stay alert for hidden hazards or traffic. P. Keep all nuts and bolts tight and keep the equipment in good operating condition. A Note to All Users List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this WOOD CHIPPER in a safe manner. Contact the dealers for assistance in your area.
Part II: Familiar with the Wood Chipper PART II: Familiar with the Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact the dealers in your area.
Part III: Operating the Wood Chipper PART III: Operating the Wood Chipper It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter. WARNING A. B. C. D. Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules” before operating the WOOD CHIPPER.
Part VI: Troubleshooting and Parts Lis Stopping 1. 2. 3. Move the Throttle Lever to IDLE. Recoil Start: Turn the Ignition Switch to the OFF position. Electric Start: Turn the Key to the OFF position. Operator Zone Wood Chipping NOTICE Woods’ and branches’ diameter should be no bigger than 120mm. WARNING Do not place your hands into the chute when loading. This is a very UNSAFE method and could result in injury to your hands. Do not reach or step across the rail while the Wood Chipper is running.
Part IV: Maintaining The Wood Chipper PART IV: Maintaining the Wood Chipper Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.
Part VI: Troubleshooting and Parts Lis Lubrication NOTICE All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use.
Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.
Part VI: Troubleshooting and Parts Lis Machine does not seem to have full chipping power. Ø The belts may be too loose and slipping. Adjust or replace belts as need.
Part VI: Troubleshooting and Parts List Explosion View and parts list Ref.No. Description Ref.No.
