User's Manual

(4) Operating the PenCam Kits:
PenCam:
Step 1: Insert the 5pcs GPA76 batteries to the pen camera as indicated in point (㆒)
Step 2: Switch on the same channel as indicated in point (㆓) to suit the receiver channel.
Step 3: Assemble the whole unit as indicated in point (㆔)
Step 4: Push the button on top of the pen to turn on, push the button again to turn off.
(You will find the button that, while on turn off mode, it is slightly higher than
when it is in turn on mode.)
Receiver:
Step 5: Connect the receiver to the equipment you wish to transmit to [monitor, TV, VCR, …etc.]
Step 6: Direct the antenna of the receiver towards the PenCam. The integrated antenna inside the case of the
receiver is located at the opposite end to the connectors.)
(㆓) Power Source “Type 2”: Using 1pc 9V Auxiliary Battery:
In addition to using different battery, same step (1)/(2)/(3)/(4) as above.
Remark: Take off the cover of the battery cell and insert the 9V battery adapter (
Negative is downward and
positive is upward),
then slip on the metal outer body which is with a hole. Plug the 9V battery snap
in the hole on the metal outer body for connecting with the attached 9V .battery.
(六) Operating Tips:
1) When putting the pen camera inside the pocket, please don’t put another metal pen or other
metal devices inside the same pocket to avoid poor transmitting quality.
2) When using the pen camera, you can fit the camera on the pen clip to aim at the subject.
If you want to adjust the angle of the lens, in avoiding attraction to other people, you can
use the pen camera to write, just like a regular pen. (Take note that the pen camera
will provide writing for only 5M in length.)
3) When holding the pen camera to write, take note that the holding position must not exceed
the rotary tube which is with shuttle pattern. Because the antenna is located at the
position of the pen head (5), if exceed the shuttle pattern (6), it will result to poor
transmitting quality.
4) The pen camera is with built-in microphone. It is an omni-directional high sensitive Mic.
No need to adjust, it is designed to detect the sound..
5) When inserting the battery, the negative(-) must be downward and the positive(+) is upward.
Wrong insertion of the batteries will cause damage.
6) The battery cover must place on top of the batteries (power source type 1). Otherwise it will cause
short circuit between the brass outer body (7) and the batteries, and will damage the pen camera.
(If the attached battery cover is lost, you can use other unit which is of isolated material to replace it.)
7) Order of inserting the 5pcs GPA76 batteries: Inserting the 5pcs GPA76 batteries piece by piece.
When inserting the GPA76 batteries, make sure that each battery is in the same direction,
Negative(-) is downward and positive(+) is upward.
(六) Important:
1) Use the attached GPA76 batteries only, or replace by the same batteries.
2) Don’t place above or near a heat source which may cause the equipment to overhead.
3) Avoid “Oily” locations.
4) Microwave ovens can cause interference and diminish the quality of the signal if the
pen camera or receiver located close by.
5) Beware of humid locations. Water droplets or spray may damage the units. If condensation
occurs, do not use until the equipment has dried out.
6) Do not use in temperature exceeding 55 degC.
7) Never paint or attach metallic labels and sticker of any kind.
8) Do not use two pen cameras and receivers operating at the same time in the same area.
This might result in picture and sound interference.
9) For a long period of not using the pen camera, please take off the batteries.
Note: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Impottant Note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device
is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void useer’s authority to operate the device