0. Set Mode Configurations 10-3 Power and Battery Setting Use this menu to set power-related options. 1 Select from the Set mode menu. 2 Press the SET CLR key to display the sub menu. BS VFO 145.000 FM 10-3-1 Auto power off setting “Auto Power Off” is abbreviated to APO. Use this function to make a beeping sound and turn off the power automatically when the receiver is not operated for the specified period of time.
10. Set Mode Configurations 10-3-2 Battery setting Use this setting to display the battery level icons correctly. 1 Rotate the upper dial to select “Battery type”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Battery type Battery pack 2 Rotate the lower dial to select “Battery pack” or “Dry Battery”.
10. Set Mode Configurations 2 Rotate the lower dial to select the time while the power is ON and the time to save the battery. When this function is set to ON, “BS” appears on the LCD. Rotating the dial switches the options as follows: OFF 0.2: 0.2 0.2: 1.8 0.2: 1.2 0.2: 0.4 0.2: 0.8 (Initial value) • This setting is factory-set to “0.2: 0.8”. Under normal conditions, it is unnecessary to set this function to OFF.
10. Set Mode Configurations 2 Rotate the lower dial to select the key lock mode. Rotating the dial switches the options as follows: All 16-key pad Dials only 17-key pad 16-key + dials All 16-key pad All operation will be locked. The operation of the key pad will be locked except for the key. Dials only 17-key pad 16-key + dials The operation of the dials will be locked.* The operation of the key pad will be locked. The operation of the key pad and dials will be locked except for the key.
10. Set Mode Configurations 2 Rotate the lower dial to select “Stay in the band” or “Go to next band”. Stay in the band Go to next band Return to the other end of the same band. Move to the next band. 10-4-4 Right/left dial function setting Use this setting to swap the functions assigned to the right and left dials. 1 Rotate the upper dial to select “Dial assignment”. The LCD displays the information as shown on the right. BS VFO 145.
10. Set Mode Configurations 10-4-6 Assigning a function to the WILD key WILD Use this setting to assign a desired menu item in the Set mode to the key. Assign a frequently used menu so you can change the setting quickly. 1 Rotate the upper dial to select “WILD key assign”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Wild key assign language 2 Rotate the lower dial to select the function to be as- signed to the WILD key.
10. Set Mode Configurations 2 Rotate the lower dial to select the band to be operated with the [MONI] key, function. Both bands Main band only Sub band only Operating band Both bands will be operated with the [MONI] key. The main band will be operated with the [MONI] key. The sub band will be operated with the [MONI] key. The band currently being operated will be operated with the [MONI] key. 10-4-9 MONI key activation setting Use this setting to specify how to operate the [MONI] key.
10. Set Mode Configurations 10-4-11 Remote COM port setting The ERW-8 is an optional cable like the ERW-7 cable which is connected to the USB port of a PC to allow the use of memory editing software. Moreover, you can use the ERW-8 to control most functions of the DJX11 in real time, and charge the battery pack. Note that these operations require additional software. The ERW-8 should be used together with the EDC-174 charger. The following setting is necessary when you use the ERW-8.
10. Set Mode Configurations 2 Rotate the lower dial to select “Busy scan”, “1sec. timer” to “25sec. timer”, or “1sec. elapse” to “5min. elapse”. Refer to the table below to select your desired mode. Busy scan mode Timer scan mode Periodic scan mode After scanning stops, the DJ-X11 resumes scanning when there is no signal to receive. After scanning stops, the DJ-X11 resumes scanning after the specified time even though it is still receiving signals.
. Set Mode Configurations 10-5-3 Priority Monitoring duration setting Use this setting to specify the time to stop the reception of signals from the priority channel when the Priority Monitoring function is ON. 1 Rotate the upper dial to select “Prio. duration”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Prio. duration Busy 2 Rotate the lower dial to select “Busy” or “1sec.” to “25sec.” You can select the busy mode or the timer mode from 1 to 25 seconds.
10. Set Mode Configurations 10-5-5 Scan speed setting Use this setting to change the scan speed. 1 Rotate the upper dial to select “Scan Speed”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Scan Speed Slow 2 Rotate the lower dial to select from three levels: “Slow”, “Normal”, and “Fast”. 10-6 Memory Setting Use this menu to set the memory functions. 1 Select from the Set mode menu. 2 Press the SET key to display the sub menu. CLR BS VFO 145.
10. Set Mode Configurations 10-6-2 Memory name display setting When memory names have been set, use this setting to select whether to display a memory name or frequency. 1 Rotate the upper dial to select “Name display”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Name display Memory name 2 Rotate the lower dial to select “Memory name” or “Fre- quency”. Even when “Memory name” is selected, you can display a frequency temporarily by holding down the [MONI] key.
10. Set Mode Configurations 10-7-2 Bell function setting The Bell function uses a bell sound to provide notification when a signal is received. 1 Rotate the upper dial to select “Bell”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Bell OFF 2 Rotate the lower dial to select “OFF”, “Main band only”, “Sub band only”, or “Either band”. When the Bell function is enabled, appears on the LCD. When a signal is received, flashes and a bell sounds.
10. Set Mode Configurations 10-7-3 Voice Guidance function setting This function reads the displayed frequency of the DJ-X11 or announces the result of the Bug Detector function in English. ● Setting the Voice Guidance function 1 Rotate the upper dial to select “Voice guide”. The LCD displays the information as shown on the right. BS VFO 145.000 FM Voice guide Disable 2 Rotate the lower dial to select “Disable”, “key opera- tion”, “Bugging mode”, or “Both”.
10. Set Mode Configurations 10-8 Remote Controller Setting This menu is available only when the optional remote controller EDS-12 is used. You can assign the functions listed in the table below to the remote controller keys as desired. The remote controller has four keys for function assignment: A through D. 1 Select from the Set mode menu. SET 2 Press the CLR key to display the sub menu. BS VFO 145.
11. Channel Display Mode 11. Channel Display Mode This mode displays only a bank and a channel number instead of a frequency in the Memory mode. Some other functions are also disabled. This mode is convenient for commercial users. 1 Program frequencies into the memory beforehand. 2 Select the memory mode and turn the power OFF. 3 Turn the power ON while hold- ing down the [MONI] and keys simultaneously. The LCD should appear like the figure on the right showing the bank and channel number.
12. Cable-clone and PC Connection Functions 12. Cable-clone and PC Connection Functions The Cable-clone function copies data from one DJ-X11 to another DJ-X11. By connecting two DJ-X11 units with a cable, you can copy the information (including memory data) specified in the sending unit (herein referred to as “Master”) to the receiving unit (herein referred to as “Slave”). In addition to the Cable-clone function the following operations are possible when the DJ-X11 is connected to a PC.
12. Cable-clone and PC Connection Functions ● Precautions common to all connections • Be sure to turn off both the DJ-X11 and external device before establishing any connection. • The earphone jack of the DJ-X11 accepts a ø3.5 mm 4-pole stereo mini-plug. Refer to the diagrams below for wiring.
12. Cable-clone and PC Connection Functions 12-2 Cable-Clone Receiving Data Use the following procedure to copy data from another DJ-X11 or to receive data edited on a PC. 1 Turn OFF the Slave and connect the stereo mini-plug cable to its earphone jack. 2 While holding down the［MONI］ key, press the ［ POWER ］key to turn ON the Slave. CLONE 57600bps “CLONE” appears on the LCD and the Slave enters Clone mode. 3 Wait until the Master DJ-X11 or PC sends data.
12. Cable-clone and PC Connection Functions 12-3 Cable-Clone Transferring Data The procedure below does not necessitate using the PC Connection function. 1 Turn OFF the Master and connect the stereo mini-plug cable to its earphone jack. 2 While holding down the［ MONI ］key, press the ［ POWER ］key to turn ON the Master. "CLONE" appears on the LCD and the Master enters Clone mode. The number increases. 3 While “CLONE” is displayed on the LCD, press the dial.
