Instruction manual
Y function is utilized when slower rudder servo causes tail hunting (wagging). This can be observed after a
g pirouette comes to a stop. If tail hunting occurs, gradually increase DELAY value to eliminate it. For best
rmance, DELAY value should be kept as low as possible without tail hunting.
Setup etnod :
Press and hold the SET button for 2 seconds to enter the setup mode, then press the SET button to select DELAY setup
mode,
as'
dicated by the lighting of DELAY LED. The choice of small or large helicopter is done by moving the transmitter rudder stick
left
Of'
while observing the color of the STATUSLED. For small helicopters STATUS LED will be red, and large helicopter will be green.
The
am
t of servo delay is set by how far you push the rudder stick, followed by pushing the SET button.
(2~~ffiJ~~jqJH~~~~~~~~ifjH~~ ' ~l!ll:~11@~~ ' n1.JiCiJf»g«el!ll:~lI~~ElM ' ~1.JiCiJ~[Q)¥IJcpTII'i«el!ll:~lI@.LtEl.~' Ilt~~~~~
~'~DD~mtJ~~ffiJ~~.' -mlffi~i'f1'~~~ilIEm~ffiJ~IlUl'~mtJ~~ffiJ~~.m(lJ\~!6' allU~f»gffiJilJj~~~l~~*i·
~: fflni:"SET"m2t!>lil\J}JIlli~~~tC, mm~DELAYmm:' ~1.JiCiJ~~j!j!mm/J\~/l*jm~~l!ll:'
ro :
T-REX
250/450
(STATUS~KiIJ~) ,~cpj;:~l!ll:~1I110T-REX500/550/600/700(STATUS~liIiRm) '~~fOJ~~~DELAY~mtJ:ii~' llmffl1.JiCiJf»g~j!j!
@fil~:lE' ~j!j!EI3cpTIl'im~"DELAY"mFT!ll1l5~m!~~O%'m~it;l;:rr~~~mtJ.~100%' ~~j!j!m~J5fT~ffiJ~~.~~ffl1'ilJ' iitLni:T'SET"mlii:8iN'
li!JOJlOJ~~:lEl!ll:~lI~tC~~~:E:·
Gradually movethe transmltterrudder.stlckunttl
DELAY LEDbegins toflash, the delayvaJue 0%;'
at th is pOint.·
mB;~·!IBB!~1!IB'~III;;I:~2:!BI~B~;<,1
~remuM"DELAY".1RI1I8,".Bi •
o.aO%
7.Sensitivity
For radio with
0% ·100% ga
mode.
n be adjusted directly. For example, 50%-100% setting on the radio translates to
;50%-0%setting on the radio translates to 0%-100% gain in the normal (non-heading) lock
st servos and helicopters. The goal is to find the maximum gain without tail hunting. This can only
ests.
ing point for transmitter's gyro gain setting should be 70-80% for hovering, 60-70% for idle-up. Value should
I flight conditions by increasing to the maximum gain without tail hunting.
-m~~Il'8~ii@(m'~:lEJ}JllliffiJ~~~ ' qr~mlil\GYROJ}Jlllimm:lirr@(m'j~ffiJ~~ ' ~:lEj~50%IlUIl'8~iiffiJ@(m'~0' ~~j~50%-100% ' llU~2filii@(m'j~
~~:lEJtl:llliffiJO-100%: ~:lEj~50%-0% ' llU~2filii@(m'i~~~F~~JtI:~ffiJO-100%•
@(m'i~ffiJj;:/J\~I\!~jqJH~~l!ll:~lIffiJ1'fOJlffi~J5fT~~' -mlffi~ ' i'f1'~~~ilIEm~ (~~lI~ffilt!:lm~E~JljffiJ~55t) ffiJirtJ~l'@(m'j~~~~!6 ' J5fT~RIlli
~~;r~mrrffiJJtl:55t*lirrfJiil~·
lil\~~~@(m'~:lEffiJmm:' IiIIUFT!ll1l5@~~lt~5t~:lEi'f70-80%~E'
Idlle
upmrr~~~i'f60-70%~E' 2~j'ijm;r~mrrffiJJtI:~j'ijrrj~IE' 110~~~~ilIE
m~~~~qrj'ijtl!l~~@(m' ' E~~~ilIEm~~ ' llUtI!l{t!;@(m'•
II&C~T~NII
For radios (IE Futaba) using 0-100% as heading lock gain scales, the recommended gain setting is 30% to 35%.
For radio that uses the 50 -100% scale(such as JR and Hitec), the recommended gain setting is 70% to 75%.
m5'ES!l!Ji:~O-100%8\J~$ .
~Futaba
·lt~~~i':E30-35%1I:tJ : m~ral\!l!i[[~50-100%8\Jjl!H~$,
~JR '
HITEC' lt~~!l!i[[iil1:~i':E70-75%1I:tJ·
S~ecifications
&lZmf!
1.0perating voltage range:
DC 3.5V-S.4V
2.0perating current consumption:
<80mA@4.SV
3.Rotational detection rate: ±300·/sec
4.Rudder yaw detection rate: ±600·/sec
5.Sensor resolution: 12bit
6.0perating temperature: ·10·C-60·C
7.0perating humidity: 0%-95%
8.DimensionlWeight :
36.5x25.5x15.6mm/11g
eRoHS certification stamp
1.~ffl~m : DC 3.5V-8.4V
2.)~~U!:)Jffi: <80mA
@
4.8V
3.~~~~&irtJ~~~m':
±300·/sec
4.~~~f»g~~m' :
±600·/sec
5.@(IJI~M;tfim': 12bit(12lli7t)
6.:tij'F~m' : -20·C-65·C
7.:tij~~m' : 0%-95%.
8.R1/mii: :
36.5x25.2x15.6mm/11
9
.mgRoHS~fflm'§ji
32