Instruction manual

ManualsBrandsAlign ManualsBaby CareTREX 700E V2

4.Gyro NOR/REV setting

NOR/REVJe •• iE&!q)IJIIIIIJI!:~

Lift up the helicopter by hand, and turn it to the left (yaw). Check if the rudder servo is applying correct compensation to the

right. If reversed, set the NOR/REV setting as follow.

Setup method: Press and hold the SET button for 2 seconds to enter the setup mode, then press the SET button to select

NOR/REV setup mode, as indicated by the lighting of NOR/REV LED. Using the transmitter's rudder stick, select either NOR

(STATUS LED is green),or REV (STATUS LED is red).

llUe~~m ' ~e~;lJ:lIfJJ • a~~jQJH~~8'iJlIi1JDIij~lI!j~~8'iJDIij~M:!TE~A1DIij~ • ~mllB.jj8'iJl1JfFDIija2JE:iHi • a1'IEIii~~~a\nE&Iij~JE

!!!:~r.jj:t : m~"SET"m2f»i!L\JJJ~~JE~n ' ~ltNOR /REV~ll'i ' ~DIij~~ltNOR( STATUSf.m~m ) ~REV ( STATUSf.m1iiH~)

2.05 (digital) / AS (analog) servo selection

DS.ro:/ASJlJ::tfPJI ••••

There is a direct correlation between servos' speed to gyro's performance. Faster servos are able to execute commands from the gyro

at faster and higher precision. Oue to the high performance gyro sensors used in the 3GX flybarless system, premium high speed digital

rudder servos are mandatory for optimal tail performance. Some of the recommended rudder servos include Align OS650, OS620,

OS520, OS420, Futaba S9257, S9256, S9254, S9253, or other servos with similar specifications.

Setup method: Press and hold the SET button for 2 seconds to enter the setup mode, then press the SET button to select OS/AS setup

mode, as indicated by the lighting of OS/AS LEO. Using the transmitter's rudder stick, select either digital servo OS mode (STATUS LEO

is green),or analog servo AS mode (STATUS LEO is red).

jQJH~~iiJfF~M1&ImIlB~jj8'iJ~1re ' jQJH&~iiJ1'Fi&!~' littIreTIIDl&BlIlB~ii~tt:l8'iJ:Fs~ ' ~.~~~$8'iJ5&~ : 83~3GX Flybarless~fH§~~~8'iJ&BI

~1lll~!U&M ' pfi~}!lliijlmgftG~~li!il'Al12jQJH&~' roALIGN OS650, OS620 . OS520 . OS420· Futaba S9257 . S9256 • S9254 • S9253~Jl;ftM§A1

m~jQJH&~ ' ~~~~€E5&§g •

!!!:~:oJ:t : m~"SET"m2f»li.i\JJJIre~JE~n ' j'ij~"SET"m~ltDS/AS~ll'i ' (OS/AS:Fsmm~i1E)' fUffl:oIijJll'8~~~ltI'HITOS (STATUSf.m~m)

~littAS (STATUSf.m1iiIm)jQJH~~•

Green LED: DS digital servo

'Red L"EO: AS analog servo

liiRm :

DS.Ul®H&~ ~

~KiI:m :

AS~lt®H&~

Green LED : normal direction ~

Red LED: reverse direction ~~

~m :

NORiEioJ ..: '";''''"

nm :

REV.&ioJ • , .' .

Using an analog servo in OS mode will

cause damages to the servo.

i':EDS~n""film"ASliltjQJH&~"~l;!J¥.:\(jQJH~~m

i!t.

Select by moving the rudder stick left and right

ti:e••

~ICiIE••

Middle tail

pitch assembly.

~PitchjggIliJm.l!!l'cp

Tail case set

A B

~efiiim.

Select by moving the rudde.r stick left and right

a:~.11T.i!q).a1l.

RUD