Instruction manual
AlLRed
Ii[
E L E
Orange
ill
PIT Yellow
RU
Green IIi\
GAIN
Blue ~
THR
Purple
:ill
GOY--++-+++h
1.Connect all wires as shown in diagram. Receiver and 3GX wires are
color coded to distinguish the different connection channels.
Care should be taken to ensure proper wire color to channel connection.
2.Receiver power is achieved by connecting the 3GX "S.BUS/BINO"
port to the ch7 or BATT port on receiver using supplied signal wire.
3.To avoid damage to servos, only digital servos should be used for swashplate.
Recommended spec: 0.1s/60oor faster, with 12Kg or higher torque.
4.3GX has built in speed governor function which can be utilized by
purchasing the optional speed sensor.
Governor setting is done through channel 7 on the receiver.
BATT OUT
set as THR on transmitter,Such as
ogram the transmitter to utilize
PIT.
IT (6)jj~ifmTHR~' i91J~08FG'12Z, 14MZ~'
)jj~ THR(6)jj~ PIT
e
1.For JR or Spektrum satellite receivers, connect wires as shown in diagram.
2.To avoid damage to servos, only digital servos should be used for swashplate.
Recommended spec: 0.1s/60· or faster, with 12Kg or higher torque.
3.3GX has built in speed governor function which can be utilized by purchasing
the optional speed sensor. Governor setting is done through channel 7 on the receiver.
Channe15/GEAR controls RPM of speed governor, channel7/AUX2 controls rudder gyro gain.
For radios with less than 6 channels,please use the standard receiver connectivity method
4.For radios with less than 6 channels, channel5/GEAR is used for rudder gyro gain.
Speed governor cannot be used. For safety concern, two satellite receives should be used,
with each antenna perpendicular (90 degrees) from each other. A satellite receiver
should be installed on each side of the frame, separate by minimum distance of 5cm.
5.Should both satellite receivers loose connectivity during flight, LE01 - LE05 will flash
continuously as warning. A single power cycle of the system will not clear this error.
The system need to be power cycled the second time to reset.
6.default channel/function mapping when using satellite receiver are:
(1)THR (2)AIL (3)ELE
(4)RUO (5)GOV (6)PIT (7)GAIN
1.~~~ ffiliDm*lR' 3GX5ZmSpektru~JR*~mr~7<;~ °
2.+~ ~!&~iD:jq]~~~, el!lU~~pxjq]~~~rnf19:
e
~~ : ~JjiO.10f»/60° ~~ : ffi/J12kg~..t
c
3.3GX~ :@~~~9<IJ~~ffl
c
tJ1J&tJ1J~..t~~~(5)GEAR~mU:@~~Q~'
(7)AU 7\J1J~l'~~~~~ffl{ll%m~7J't\
e
4.ifm~~JI:e~ -~7<;*lR' ~i~~~7<;~J'i'3JjiIl*!.I)\\~¥.gOJji2.9j.,
'§~~!&1F: ~
5ib1~..t
c
5.110~mD~ ~~jlEJ'jJm~' LED1-LED5~~.~m1iH§'
i'±Jlt~~l' ' LED1-LED5~~.~m1ffilmt$m1~ '
!.I)\\~~mifJT '
:::rq[IE:lf;lii'F
e
6.~ffl~~7<;
m*lR~. ~!iIljj~8ttiJ:@ifm:
(l)THR (2)AIL (3)ELE
(4)RUD (5)
GOV
(6)PIT
(7)
GAl
N
1.00 not mix satellite receivers of different makes.
2.Even under correct startup sequence, if transmitter is powered off first, LE01-LE05 will also flash.
Thus the receiver should always be powered off before the transmitter. .
3.3GX supports satellite receiver models currently available on the market. Should new receiver version
comes out with compatibility issues, firmware will be updated to resolve any incompatibility that may arise.
1.1' ~7<;~~~J~.S<.W~
c
2. »r.l" 110~7tmJ~~n~, ttl~~~LED1-LED5~.~m1~»t, pjf~~ftpx7tmJmJ&~' ~mJ~nEJ'jJ~16~~
c
3.110 ~7<;*lR~~1'ffigm~ ' ~~lI1J~~ifJT7J't\1!i¥~
c
25
.....
_.
,------------------------------------------------~