Instruction manual
To set this option is to turn on the transmitter and connect to BEC power.
U~D~iill~§!~~ ,
m.t.BECIlt~IDlOJlifi~i'F•
I
JR Transmitter/Servo
JRUH!!IBljqJD~BllfRt
I
Positions of CH2' CH6 are exchangeable, After
assembling as photo (Note:Set the transmitter
under CCPM 120 degrees mode), pull throttle
stick (pitch) upward. If one swash plate servo
(or two servos) moves downward, adjust
reverse switch (REV) on the transmitter to
make it moves upward. If three servo move
downward, adjust the travel value
(+-)
of
SWASH CH6 on the transmitter to make them
move upward. When the actions of Aileron and
Elevator are opposite, adjust travel values of
SWASH CH2 and Ch3.
CH2' CH5~MftG!!!i '
120'+'f'Ur:) ,~'
~1':l1
~
&~,
Elevator: CH3
rt-~'CH3
I
FUTABAlHITEC Transmitter/Servo
FUTABAlHITEC~~H!!IBljqJD~HllfRt
I
Positions of CH1 ,CH6 are exchangeable, After
assembling as photo (Note:Set the transmitter
under CCPM ~ord~grees mode), pull throttle
stick (pitch) upward.'lf one swash plate servo
(or two servos) moves downward, adjust r
everse switch (REV) on the transmitter to make
it-moves
upward. Ifthree~servo move
downWard>,adjust th~:;trave,1value
(+-)
of
SWASH
CFtS
on-the'lransniitter to make them
move upward. When.'the actions of Aileron and
Elevator are o~site, adjust-travel values of
SWAS CH1 and Gh •
6\H1 'CH6llT:g]!!;~1!!I •
~i11i1~li()±~,H~;jiIDt:<E~
C€PM
120"T,'f'Ur:) ,
~JillP~li"(Pitch)l:U:J!!;. :S+'¥'II!!
,i<iI!!l,H1fJ~2i1!11±1'~~ . ~iIIlmli~~elJ&.IlIIIm(REV)1iE
lQ]!Iil~ vE3f1IHOI!Iil~jcJ~1±1'~~, r.RiIIl!l~ll!!
SWAS[;I,CH6~.elJIE~~ , jflOl!lilll!!jcJ~I±LIjZ.f3i·'
;]H~
~fj!llJfFl!l&~ • ~li!lilll!lSWASHCH1' CH2D~.IEw;'iii •
I
TAIL NEUTRAl. SETTING
~c:pnJOID!:~
I
After setting Head Lock mode, correct setting position of tail servo and tail
pitch assembly is as photo. If the tail pitch assembly is not at the neutral
position, please adjust the length of rudder control rod to trim.
~.lIB!;:Elt~jqaHI!~~
Pitch~ltiIHllIEiUg~li1~ •
EI!§
Pitch~ltiIJm*.ifJ~m!lllm~
~fijJi!~f!!l&~",,~IE'
I
HEAD LOCK DIRECTION SETTING OF GYRO I\'8l!ilmJEJ5~~JE
I
To check the head lock direction of gyro is to move the tail
counterclockwise and the tail servo horn will be trimmed
clockwise. If it trims in the reverse direction, please switch
the gyro to"REVERSE".
I\'8l!ilmJEJ5~m~'~~~~W~.&~~,~~~ft~~.m
i~IE ' ,&~.~t7J~I\'8I1i1.t."mJE,&~"ImIm~IE •
Middle
tail
pitch
assembly.
~Pitch~ffilJm~ifJ
Tail case set A
I
B
~aJfiil
f---1
~
Tail moving direction
lillJ~!lIlJ'jtq]
Tail servo horn
~/QJ!IilJIJt!f
22