Advanced Image Processing Solutions Dual SD/HD Video Delay Installation and Operation Manual C3034-8001-100 Copyright Algolith 2008, all rights reserved
Guide to installation and operation VLD-1002-MD Table of Contents Safety ...........................................3 Specifications ..............................28 Introduction ...................................4 Limited Warranty .........................29 Overview ............................................... 4 Main Features ........................................ 4 The Algogear Series ............................... 5 Contact us ..................................29 Installation and setup .
VLD-1002-MD Guide to installation and operation Safety Electromagnetic Compatibility Before using this product, carefully review all the safety precautions in this user guide, and all the important regulatory and safety notices in the openGear DFR8310-C Multi-Definition Digital Products Frame User Manual.
Guide to installation and operation VLD-1002-MD Introduction Overview The Algogear VLD-1002-MD Video Delay is designed for delay applications in both standard and high-definition SDI environments on up to 2 channels. It supports all popular standard-definition and high-definition video formats including 480i59.94, 576i50, 720p50, 720p59.94, 720p60, 1080i50, 1080i59.94 and 1080i60. Delay programming can be added in time units (seconds) and video units (frames).
VLD-1002-MD Guide to installation and operation The Algogear Series Designed for openGear, Algogear is a flexible, future-proof, modular solution that can maximize bandwidth, clean, synchronize and scale media. Algogear delivers unparalleled value and flexibility to broadcasters leveraging the Algogear solution, giving the ground-breaking ability to reprogram the cards with any of the available Algogear solutions at any time, at no cost.
Guide to installation and operation VLD-1002-MD Installation and setup Static Discharge Whenever handling the VLD-1002-MD and other related equipment, please observe all static discharge precautions as described in the following note: Static discharge can cause serious damage to sensitive semiconductor devices. Avoid handling circuit boards in high static environments such as carpeted areas, and when wearing synthetic fiber clothing.
VLD-1002-MD Guide to installation and operation Installation and setup The VLD-1002-MD card is installed in the openGear frame. openGear frame The VLD-1002-MD card requires a BNC rear output module. Depending on the frame model you purchased, your frame may be equipped with a fixed 100 BNC rear panel. openGear frame with a fixed 100 BNC rear panel Your frame model may have a modular rear panel, to accommodate different types of cards.
Guide to installation and operation VLD-1002-MD Power Consumption The power rating of the openGear frame allows 125 watts to be redistributed over 10 slots. A single slot may exceed 12 watts but the overall power consumption shall not be above 125 watts. The VLD-1002-MD dissipates 14 watts. An openGear frame, when populated with Algogear cards only shall use no more than 8 slots. Blank slot fillers can be used to block slots in an openGear frame.
VLD-1002-MD Guide to installation and operation 6 status LEDs are located near the VLD-1002-MD card’s front edge. Consult the graphic and color code below to identify the LEDs and their meanings. Card Status - LED color code Green Yellow Red Normal Minor Problem Critical error Rear Input / Output Module Labels Algolith’s VLD-1002-MD card comes with the rear module labels of every available Algogear product at the time of purchase.
Guide to installation and operation VLD-1002-MD Output Channels The VLD-1002-MD has 2 HD/SD-SDI inputs and 4 HD/SD-SDI outputs. Each channel in the Dashboard user interface corresponds to the matching input number. The label on the card’s BNC rear output module, at the back of the openGear frame, identifies the inputs and outputs.
VLD-1002-MD Guide to installation and operation Operation Once installed in the openGear frame, the VLD-1002-MD card is controlled through the Dashboard software (version 2.2 or higher). For information on how to install the software and to manage openGear frames in Dashboard, please consult the Dashboard Software User Manual, provided on the installation CD you have received with this purchase, or visit our website at: http://www.algolith.
Guide to installation and operation VLD-1002-MD The Basic Tree View Window All openGear frames and compatible cards in your system are displayed in the Basic Tree View window. Select the card you wish to control in the Basic Tree View window. For more information on the device list please consult the Dashboard Software User Manual. The Product Status Area The product status area of the Dashboard interface displays the selected card’s product name, the card’s status (i.e.
VLD-1002-MD Guide to installation and operation The Card License Window In order to be able to repurpose your Algogear card, a license must be available within the card for the Algogear product you want to switch to. The Card License Window displays the Algogear product that were available at the time of your purchase, and for which you have a license. For more information on how to repurpose your Algogear card, see the «How to Repurpose your Algogear Card» section, on page 22.
Guide to installation and operation VLD-1002-MD Adjusting Parameters The VLD-1002-MD card provides an extra level of control and security with an administrator password-protected level, in which the parameters of the card can be modified and controlled. The non password-protected level or «read only» mode, where no password is entered, allows users to view the various settings, but does not permit changes to be made.
VLD-1002-MD Guide to installation and operation The Card Setup Window The Card Setup window allows the configuration of parameters affecting the overall functionality of the card. Recall & apply settings Save settings Save Settings Destination The Save Settings Destination function allows the user to save up to 4 configurations of the VLD-1002-MD card’s parameters per channel.
Guide to installation and operation VLD-1002-MD Selecting the Reference The VLD-1002-MD card provides four methods for referencing the incoming video signal. At the bottom of the Card Setup window, the reference selection can be chosen from a drop down menu. The reference selection is automatically saved and will be restored after power-up. The VLD-1002-MD accepts tri-level, bi-level and black burst reference signals. The video inputs can be synchronized with the house sync signal.
VLD-1002-MD Guide to installation and operation External Card (BNC 10): Uses the reference signal from the VLD-1002MD card’s rear module REF input.
Guide to installation and operation VLD-1002-MD Video Setup Window The Video Setup window allows the configuration of video parameters affecting the individual channels of the card. Video Default Mode The Video Default mode function is used if no valid video is detected at the input. The VLD-1002-MD can be set to respond to these problems with the Video Default Mode function.
VLD-1002-MD Guide to installation and operation Video Delay The Video Delay function allows users to adjust the video delay in increments of frames and seconds. Video Delay (sec) The Video Delay (sec) function allows users to adjust the video delay in increments of one second. The following table lists the possible values according to the video format: Format Video Delay (sec) values 408i59.94 1 - 24 576i50 1 - 24 720p50 1-4 720p59.94 1-4 720p60 1-4 1080i50 1-4 1080i59.
Guide to installation and operation VLD-1002-MD Maximum Delay in Seconds & Frames The maximum video delay per channel varies with the input video’s frame rate, and is reached with the following settings in seconds and frames: Video Format Maximum delay Seconds Frames 480i59.94 24 15 576i50 24 15 720p50 4 25 720p59.94 4 31 720p60 4 31 1080i50 4 12 1080i59.
VLD-1002-MD Guide to installation and operation The Alarm Setup Window Alarms reported to Dashboard Problems detected by the VLD-1002-MD card are transmitted as alarms to the card’s LED, to the Dashboard interface, and to the optional SNMP monitoring. The problems detected can be reported to the user as minor alarms or critical alarms.
Guide to installation and operation VLD-1002-MD How to Repurpose your Algogear Card Algogear cards are easy to reconfigure. First, visit our website in the support section, at: http://www.algolith.com/support/downloads/ repurpose-algogear You will find a list of the Algogear products available for you. Select the Algogear solution you would like to download onto your existing Algogear card. Next enter your name and email address and press the Download Solution button.
VLD-1002-MD Guide to installation and operation Load the new product onto your card The instructions below will help you quickly and easily repurpose your Algogear card with a new Algogear application. Please take the time to read through the steps before beginning the process so that you have all the necessary information on hand before you begin. 1. Repurposing an Algogear card can only be done through the Dashboard software application (to download Dashboard visit http://www.algolith.
VLD-1002-MD Guide to installation and operation 4. Next you will need to upload the downloaded file onto the Algogear card. Click on the Upload button to select the .BIN file in the directory in which it is stored, and click the Open button. Click Upload to get to the .BIN file You will get a confirmation dialog box that displays the selected upload file name, type, size, and the file creation date. Click on Continue to start the uploading process (an Uploading Progress dialog box opens).
Guide to installation and operation VLD-1002-MD 5. Be patient! The upgrade process can take a few minutes. While the files are being decompressed, the Dashboard user interface displays an «Upgrade in Progress» message. After decompression, the files are installed and Dashboard loses connection with the card. An error message is then displayed. See graphic below. Card is in the process of being repurposed This step is normal in the upgrade process and must not be interrupted. 6.
Guide to installation and operation VLD-1002-MD 7. Once the card has rebooted, you should see the name of the new Algogear product you have installed on the dot matrix display located on the board. XVC1001U Dot matrix display ALGOGEAR NOTE: If you don’t see the product name, but instead the following message: “LICENSE?”, an error has occurred with the license file and you should contact Algolith customer support immediately for assistance at 1.877.ALGOLITH ext 3509. 8.
VLD-1002-MD Guide to installation and operation Congratulations, you have successfully repurposed your Algogear card. To request new rear module labels and card labels, email your name, shipping address, phone number and the Algogear applications you require at support@algolith.com.
Guide to installation and operation VLD-1002-MD Specifications* SD/HD SDI Video Signal: SD (SMPTE 259M-C) (270 Mbps) HD (SMPTE 292M) (1.485, 1.485/1001 Gbps) Formats: SD 480i59.94, 576i50 HD 720p50, 720p59.94, 720p60, 1080i50, 1080i59.94, 1080i60 Format autodetected Ancillary Data: Passthrough Video Inputs Connectors: Return Loss: Impedance: Video Outputs Connectors: Return Loss: Jitter: Impedance: Reference Connector: Two (2) BNC SD >21 dB up to 270 Mbps HD >14 dB up to 1.
VLD-1002-MD Guide to installation and operation Limited Warranty Limited Warranty Coverage Algolith Inc. warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase. If equipment fails due to such defects, Algolith Inc. will, at its option, repair or provide a replacement for the defective part or product.
