021 USB Dual Handset Adapter for Nortel 1100-Series IP Phones User Guide Document#: 90-00039 sales@algosolutions.com support@algosolutions.com www.algosolutions.
Algo 1021 USB Dual Handset Adapter User Guide Table of Contents About the USB Dual Handset Adapter ...................... 3 Keypad Functions...................................................... Volume Control ........................................................ Audio States ............................................................. Normal ................................................................. Mute...................................................................... Exclude..............
About the USB Dual Handset Adapter: Keypad Functions About the USB Dual Handset Adapter The 1021 USB Dual Handset Adapter allows two people to share a Nortel IP Phone 1100 Series so they can join in on the same telephone call. Capable of supporting any combination of two handset or headset devices, features of the USB Dual Handset Adapter include individual volume, muting, and on/off ("exclude") control. Keypad Functions The illustration below displays the keys and their functions.
About the USB Dual Handset Adapter: Audio States Soft clicks are provided when pressing volume keys until maximum or minimum level is reached. The audio level settings will reset to default after 60 seconds of silence to the receiver. Audio States There are three audio states per user: 1. Normal 2. Mute 3. Exclude Normal In Normal mode, both the microphone and the speaker are operational and the audio is heard and transmitted normally. A high tone is provided when entering Normal mode.
Installation and Setup: Setup Diagram Installation and Setup Setup Diagram USB Dual Handset Adapter 1100 Series IP Phone Fasten connecting arm of USB Dual Handset Adapter to IP Phone with supplied screws Wheel Tilt Lever USB Connection USB Dual Handset Adapter Ports IP Phone Ports PC Port Handset Port Data Port Power Headset Port Left Handset/ Headset Port Right Handset/ Headset Port Installation Instructions Connect USB Dual Handset Adapter 90-00039 1.
Installation and Setup: Installation Instructions Wheel on the Adapter to release the adjustment mechanism. To open stand, push Tab down to release latch while lifting up at other end 3. At the back of the IP phone, remove the rubber plug from the Accessory Expansion Module (AEM) port and plug it into a similar port on the USB Dual Handset Adapter. Note: although the AEM port is not used, the plug’s removal is necessary to physically mate the USB Dual Handset Adapter to the IP Phone. 4.
Installation and Setup: Configure the IP Phone Adjust the Stand Angles 6. Adjust the combined IP Phone and USB Dual Handset Adapter stands to the desired angle. Then turn the wheel on the adapter to tighten its stand in place. Configure the IP Phone The USB Dual Handset Adapter is a USB device and the IP Phone must be set to recognize it. To do this: 1. Double-press the Services key on the IP Phone. Services Key 2. Select Preferences.
Installation and Setup: Standard Two-Handset Configuration 3. Select Headsets. 4. Under Active Headset Device, select USB then press the Apply key to save the changes to the phone. 5. Proceed with Standard or Optional Headset configuration as described further on in this User Guide. Standard Two-Handset Configuration www.algosolutions.
Installation and Setup: Standard Two-Handset Configuration In this configuration, both handsets are connected to the USB Dual Handset Adapter. To do this: 1. Disconnect the coiled handset cable from the IP Phone handset port and connect it to the bottom left connector of the USB Dual Handset Adapter. This handset will be for the “primary user” and should rest in the cradle of the IP Phone. 2.
Installation and Setup: Two Handsets with Headset Configuration Two Handsets with Headset Configuration Headset In this configuration, the primary user can use ONLY the handset of the IP Phone; OR a headset AND handset connected to the USB Dual Handset Adapter. 1. The IP Phone handset remains connected to the handset port of the IP Phone. 2. Connect the primary user's headset to the left connector at the bottom of the USB Dual Handset Adapter. 3.
Regulatory Information: Two Handsets with Headset Configuration set connected directly to the IP Phone will be inactive. Only the primary user can end a call. To end a call, hang-up or press the Goodbye key of the IP Phone.) Regulatory Information This device complies with Part 15 of the FCC Rules.
Algo Communication Products Ltd. 4500 Beedie Street Burnaby, BC Canada V5J 5L2 www.algosolutions.com Sales & Support: Toll-free (USA or Canada): 1-877-884-2546 Or 1-604-454-3790 sales@algosolutions.com support@algosolutions.
