User Manual

6 7
SETUP MENU
To enter the Setup menu, rst hold down the PAGE / MENU knob (lower right,) then hold the
left foot switch.
Turn the lower left knob to scroll through the available parameters, then turn the lower right
knob to set its value.
Hold the PAGE / MENU knob (lower right) to save your settings and exit the menu.
M.JACK EXPRESSN MultiJack is expression pedal input, set here if not using jack
FOOT. SW MultiJack is foot switch input
MIDI MultiJack is MIDI input (requires MIDI to TRS adapter)
PRST.EX MultiJack connects to Expander Switch for preset selection
SCRL.EX MultiJack connects to Expander Switch for preset scrolling
CHANNL Sets MIDI input channel
STEREO MONO IN INPUT jack is mono, outputs are stereo
INP. SUM INPUT jack sums to mono, outputs are stereo
STEREO INPUT jack is stereo, outputs are stereo
RPHASE NORMAL R / DRY output phase normal
INVERT R / DRY output phase inverted
PRESET Sets number of presets available on device. Does not aect MIDI.
DISPLY PRESET Display shows preset except when turning knobs
KNOBS Display shows knobs except when loading preset
BLANK Display is o when not adjusting knobs
BRIGHT Sets display brightness
RETURN Pedal will retun to the main control page after 5, 10, 30 seconds
MIDOUT OFF Pedal does not send MIDI CC values when knobs are turned
JACK Pedal sends MIDI CC from MultiJack
USB Pedal sends MIDI CC from USB MIDI
BOTH Pedal sends MIDI CC from both
TRAILS NORMAL Hard bypass
TRAILS Trails bypass, allows reverbs or delays to ring
AUTO Auto-Trails bypass, trails ring but are faded after 10s.
EXP LO Sets the heel down calibration for the MultiJack expression pedal
EXP HI Sets the toe down calibration for the MultiJack expression pedal
TAPCNT Enable or disable tap tempo timer display
PWR ON Choose BYPASS or ENGAGE to set the power-on state of the pedal
RESET Turn to reset CONFIG, PRESETS, or ALL. Hold MODE to reset.
Set to MIDI DUMP to export the pedal presets over USB MIDI.
TURN TO
SCROLL
ITEMS
TURN TO
CHANGE
ITEM
PRESETS
TURN TO
CHOOSE
LETTER
TURN TO
CHANGE
LETTER
HOLD LEFT FOOT
SWITCH TO CANCEL
HOLD RIGHT FOOT
SWITCH TO SAVE
BYPASS | PRESET
TAP | CTRL
How do you make quick changes on a pedal that has 12+ knobs? PRESETS. Every
Leap Series pedal allows you to save up to 32 presets that contain the entire state of
the pedal.
Loading a preset recalls all knob positions, sound modes, and expression pedal
mappings.
To load a preset, hold the BYPASS / PRESET foot switch. You can set the number of
available presets in the Setup Menu, from 1 to 8. You can also set the pedal to access
the upper banks of presets (9-16, 17-24, 25-32) in the same menu. This allows you to
use multiple banks of presets for different gigs, bands, instruments, whatever you like.
Hold both footswitches to scroll back to the previous preset.
If eight presets per bank isn’t enough, you can enable a double-bank of 16 presets by
setting PRESET = 1-16 or 17-32.
You can also use an external MIDI controller to load any preset from 1-32, regardless of
how the Setup Menu is congured.
To save a preset, rst use the pedal knobs to tweak the sound, then hold the Page
knob. Press and hold the BYPASS / PRESET foot switch to enter the save menu.
If you want to save to the current preset, you can just hold down the BYPASS /
PRESET foot switch again. If you prefer to rename the preset, turn the lower left knob
to select a character in the name and turn the Page knob to edit that character. You
can also change the save location by highlighting the preset number then turning the
Page knob.
Press and hold the BYPASS / PRESET foot switch to save, or hold the TAP / CTRL foot
switch to cancel the save.