Log Splitter Operation Manual Please carefully read this operation manual before starting work.
Thank you for purchasing Log Splitter. Please carefully read this operation manual and strictly observe these instructions for the safety of you and the personnel around you. In this manner, you will enjoy long and satisfactory use of this product. GENERAL SAFETY RULES Warning: All the operation and use of the machine may have some risk, but with operator caution this will reduce the risk of injury. also, can result in injury to the operator, remove damage of property. 1.
Symbols used Standard graphic symbols are used on all machines in order to ensure complete safety of all parts of the Log Splitter. As these symbols are very important, read the information below attentively. It is obligatory to read the machine's use and maintenance manual in full before using the machine, It is obligatory to wear safety footwear at all times to provide protection against the risk of logs accidentally falling on feet.
Electrical Safety MAIN SPECIFICATIONS Never operate this tool if there is an electrical hazard. Never operate an electrical tool in wet conditions. Never operate this tool with an improper electrical cord or extension cord .Never operate this tool unless you are plugged into a properly grounded outlet. Which supplies specified power and is protected by a 16 Amp circuit breaker. Max.
We recommend the use of the following hydraulic oil for the hydraulic ram: SHELL TELLUS T22 ARAL VITAM Gf22 SP ENGERGOL HCP22 6. Never split 2 logs at one time otherwise the log may jump up .This is dangerous! 7. Never put or change log when machine in running because this is very dangerous. 8. When the machine is running, please keep bystanders and animals at least 5 metres away from the machine. 9. Never tamper with the electrical or working MOBILDTELL Or equivalent oils Never use other kinds of oils.
Figure 1: List of major components Check these components according to the following list and Figure 1. A. Log guiding plates B. Log pusher C. Operating handle assembly D. Wheel and frame E.Oilpump F. Electrical motor switch G. Electrical motor assembly H. Supporting feet 1. Main body J. Splitting wedge All the screws, bolts, washer and jig are in the packing box.(The complete list is on the attached part list).
Put the main part on the foam material and fix with 2 screws (21) and 2 nuts (20) and tighten up the supporting feet (19). (See Figure 3) On the main part that has been fixed on the foam block with the supporting feet. Use safety ring (59) to fix 2 wheels (60) onto the shaft of wheel frame (61). Then use the wheel shaft cover (58) to cover the wheels. Made sure that the wheels are not obstructed and turn uniformly.
. Stack as you work.This will provide a safer work area. By keeping it uncluttered. and avoid the danger of tripping. or damaging the power cable. 4. Position the log splitter securely and on level ground or a secure stand.If necessary block the wheels to prevent the log splitter from moving during use. 9. See point and question 5. solid supporting platform, 60-70cm high without any objects on it. Which could prevent complete freedom of movement for the operator while working.
Warning! Be sure to unplug the power before any maintenance work! Warning! Be sure to dispose of the dirty oil properly. Take it to your local,waste oil-recycling center. Never dispose it on the ground or mix it with household rubbish. Changing the Hydraulic oil . (The quantity of the hydraulic oil and recommended type have been indicated on page 5). 1. Make sure the LOG PUSHER (B in Figure 1) is fully retracted. 2. Unscrew the DIP STICK (10) and remove it together with O-type oil seal (1l).(Figure 6) 3.
Trouble-shooting Problems that may arise when using the log splitter and recommended actions are shown in the table below. In the case that operation is carried out by unauthorised operators the guarantee is null and void, and the manufacture is not responsible for any injury to the operator, bystanders, animals or damage. Problem Probable cause Corrective action Log fails to split Incorrect positioning of the log Log exceeds permitted dimensions or the wood is too hard for the capacity of the machine.
10
No. 1 Description NutM14 MI4 £., Qty No. 2 47 Motor supporting (up) 1 2 48 O-ring oil seal 50x2.4 2 Description Qty 3 Hammer ram 1 49 Gear chamber 1 4 Spring 1 50 Fixing pin 2 11 5 Cylinder I 51 Gasket for axle 6 O-ring oil seal 25x3.55 1 52 Column pin 7 Piston 1 53 Gear axle 1 2 2 2.5 1 8 O-ring oil seal 43.7x3.
