Use the hex keys in the box. You may need to use a drill for this step. Three or more people are required at this stage. 3+ You may need a ladder. Do not tighten screws all the way for now.
4X 2X 2X 1X 1X 1X 1X 1X 1X 2X 2X 1X 1X 2X 2X 1X 1X 5X 5X 4X 8X Page 2
X 5X OVERALL Page 3
St ep 1 A 4X Connect A and A1 or A2 by using supporting part V and bolt J to build the four poles (2xA&A1 and 2xA&A2). J A J A1 2X A1 or A2 A2 2X J J V 8X J M6x16 64X A1 or A2 V Don't tight the bolts too much when you insert A into A1 or A2. S4 Q 1X S t ep 2 Connect Part I and 4 poles by using bolt J Tight bolt J after A connected with A1 or A2 vertially.
St ep 3 Connect B , B1 and B2 by using supporting part V1 and bold J to build the main beam 1 . B 1X J V1 J B2 B B1 1X J B2 J C2 1X B2 1X B J V1 J B1 C 1X B1 B2 J J C1 1X Connect C, C1 and C2 by using supporting part V1 and bold J to build another main beam 2.
St ep 4 M6x15 M 16X Connect the main beam 1 and main beam 2 with the four poles using bolt M. B & B1 A1 & A2 M S6 Q 1X B2 B A2 A1 B1 C1 A1 A A2 C C2 A A A St ep 5 D 2X 1. Insert the hook into the slot of part D, Repeat twices. X5 N D E 1X N 10X 2. Insert the hook P and hook O into the slot of part E. Please insert the hook P by this way.Don’t insert the hook P opposite way as diagram! N D X4 O 4X O E P 1X P X1 Attention: Always keep hook P and C1/C2 in the same side.
Step 6 Connect D and D1 to build the cross beam (D&D1) by using bolt J and supporting part V2 D 2X J J D1 2X D1 V2 D J J V2 2X D1 D M6x16 J 16X S4 Q 1X Step 7 Connect the cross beam (D&D1) with the four poles using bolt M.
Step 8 J E 1X 1. Connect E and E1 by using supporting part V2 and bold J to build the cross beam (E&E1). J E1 E1 1X V2 E J J F 2X E F1 2X J J 2. Using the same method as the last step, use F and F1 to build the cross beam (F&F1). F1 V2 3X V2 F S4 J J M6x16 J 24X F1 F Q 1X Step 9 L 6X E1 Connect the cross beam (E&E1) and (F&F1) with the main beam 1 and 2. Attention: Always keep hook P and C1/C2 in the same side.
Step 10 Insert G, G1, H, H1 into the canopy from its side G 1X G1 G G1 1X H 5X H H1 5X S S H1 H S 1X Step 11 Connect G&G1 and B&B1 by bolt K, and hold the canopy with the frames. K J M6x16 10X B & B1 G & G1 Connect the canopy and the hock using bolt J K 3X M6x30 S4 J Q 1X H1 Pull the line from the canopy and put on hook to tighten the canopy.
Step 12 T 1X R T S T P Hook part T onto hook P Step 13 A2 U 16X T Secure the foot I to the ground using part U.
