User manual OPED I N VEL DE NY RMA GE MANUA L 20 V LI-ION CORDLESS IMPACT DRIVER BRUSHLESS nse om my ha c o n t ro l.
1 3 4 Dok./Rev.-Nr.
Contents Contents 1 Impact driver 2 Belt clip 3 Screw bits, 3× (PH2, PZ2, slotted 5) Supplied connecting elements 4 Fastening screw Required tools (not supplied) 5 5 Cross-head screwdriver 3
Table of contents Table of contents Contents .......................................................................................................... 3 Supplied connecting elements .............................................................................. 3 Required tools (not supplied) ................................................................................. 3 General information .......................................................................................
General information General information Reading and storing the user manual This user manual accompanies this 20 V Li-Ion cordless impact driver brushless (referred to below only as the ‘product’). It contains important information on safety, usage and care. Before using the product, read the user manual carefully. Pay particular attention to the safety notes and warnings. Failure to comply with the instructions in this user manual may result in severe injury or damage to the product.
Explanation of symbols Residual risks Despite proper use, inconspicuous residual risks cannot be completely ruled out. The following risks may arise due to the design of the product: • Injury caused by touching rotating parts; • Crushing or other injury through improper use; • The bit or workpiece breaking. Explanation of symbols The following symbols are used in this user manual, on the product or on the packaging.
Safety Safety Explanation of notes The following symbols and signal words are used in this user manual. WARNING! Indicates a hazardous situation that, if not avoided, could result in death or serious injury. Warns against potential damages to property. NOTICE! General power tool safety instructions WARNING Read all the safety notes, instructions, illustrations as well as technical details supplied with this power tool.
Safety c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not use the cord for improper purposes such as for carrying the power tool, for hanging it up or for pulling or unplugging it from the socket. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use only extension cords that are suitable for outdoor use.
Safety g) If there is an option for installing dust suction devices and dust containers, these should be attached and used correctly. Use of dust collection can reduce dust-related hazards. h) Do not be lulled into a false sense of security and ignore the safety rules for power tools, even if you are well acquainted with power tools, having used them frequently. Using power tools without due care and attention can cause serious injuries in a split second.
Safety h) Keep handles and handle surfaces dry, clean and free from oil and grease. Slippery handles and handle surfaces will prevent you from operating and controlling the power tools safely in unforeseen situations. Cordless tool use and care a) Only charge the rechargeable batteries with chargers recommended by the manufacturer. Chargers designed for a particular rechargeable battery type pose a risk of fire if used with other types of rechargeable battery.
Safety Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) Never perform maintenance on damaged rechargeable batteries. Only the manufacturer or authorised service companies may perform maintenance on rechargeable batteries.
Safety WARNING! Risk of injury! This product is not intended to be used by persons with impaired physical, sensory or mental abilities or who lack experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by such a person on the use of the device. − Supervise children to ensure that they do not play with the product. NOTICE! Risk of damage! Improper handling of the product can cause damage. − Do not clean the product with aggressive solvents.
Product description Product description The product is an impact driver 1 for screwing in or unscrewing screws. The screw bits 3 supplied can be clamped in the tool holder 13 for this purpose. The screw bit is locked into the tool holder by the locking sleeve 6 . The product has an on/off switch 12 , a direction switch 8 to set the direction of rotation, and an LED work light 11 for working in low light conditions. The product is powered by a separately available rechargeable battery 14 .
First use First use WARNING! Risk of injury! Packaging material and small parts pose a risk of injury to children. Children may get caught in the packaging wrapper or swallow small parts and choke on them. − Do not allow children to play with the packaging wrapper or small parts. Checking the product and package contents 1. Lift the product out of the packaging with both hands. 2. Place the product on a level, stable base, such as a workbench. 3.
Use Inserting a screw bit Proceed as follows to clamp bits in place: 1. Make sure that the product is not operational. 2 8 12 2. Lock the On/Off switch 12 by moving the direction switch 8 to the middle position (see Fig. 2). 3 3 13 6 3. Pull the locking sleeve 6 forward (see Fig. 3). 4. Insert the screw bit 3 all the way into the tool holder 13 . 5. Let go of the locking sleeve to secure the screw bit in place.
Use 4 3 13 6 6. To remove the inserted screw bit 3 , pull the locking sleeve 6 forward and pull the screw bit out of the tool holder 13 (see Fig. 4). As well as the screw bits supplied, you can also use other screw bits or inserts with a ¼" hexagonal profile. Switching the product on and off Switching on 5 12 − Press and hold the on/off switch 12 (see Fig. 5). The LED work light 11 will turn on when the on/off switch is gently pressed all the way down.
Using the battery Switching off − Let go of the on/off switch 12 . Setting the direction of rotation You can use the direction switch to change the direction in which the product rotates. 6 8 − Press the direction switch 8 to the left (see Fig. 6): the product turns anti-clockwise. − Press the direction switch to the right: the product turns clockwise. Using the battery WARNING! Risk of injury! Incorrect use of the rechargeable battery and charger can cause injury.
Using the battery Charging the battery − To charge the battery, follow the instructions in the user manuals for the battery and charger being used. Inserting and removing the battery 7 10 14 14 Rechargeable battery (not included) − To insert the rechargeable battery 14 , slide it into the battery holder 10 until you hear and feel it click into place (see Fig. 7).
Troubleshooting Troubleshooting Problem Possible causes Solution The product does not turn on. The battery does not have enough power. Charge the rechargeable battery 14 . The battery has not been inserted properly. Slide the battery into the battery holder 10 on the product. The battery must lock into place with an audible and noticeable click. The direction switch 8 is in the middle position. Press the direction switch all the way in the desired direction.
Storage NOTICE! Risk of damage! Improper handling of the product can damage the product. − Do not use any aggressive cleaners, brushes with metal or nylon bristles, or sharp or metallic cleaning utensils such as knives, hard scrapers and the like. They could damage the surfaces. Cleaning − Use a soft cloth or brush to clean the housing. − Clean the vents 7 and the area around the tool holder 13 as well. − Remove dust by blowing it out with compressed air.
Technical data Technical data Information on the cordless impact driver Article number: Model: Model number: Rated voltage: Torque: Idle speed n₀: Number of strokes: 813545 FID 20-I BL WU5451673/WU5451674 20 V max. 180 Nm 0-2400 min-1 0-3300 min-1 Chuck: ¼" (hexagonal) Weight: 1.
Noise/vibration information Noise/vibration information WARNING! The specified total vibration value and noise emission values have been measured according to a standardised test method (EN 62841-1 & EN 62841-2-2) and can be used to compare power tools with one another. They can also be used for a provisional assessment of the load.
Disposal Disposal Disposing of the packaging BOX Dispose of the packaging separated into single type materials. Dispose of paperboard and cardboard with waste paper and plastics with recyclable waste. Recycle Disposing of the product − Dispose of the product in accordance with the disposal regulations in force in your country.
Declaration of Conformity Declaration of Conformity GB IE Conmetall Meister GmbH Oberkamper Straße 39 42349 Wuppertal Germany EC Declaration of Conformity We declare with sole responsibility, that the product listed below … 20 V LI-ION CORDLESS IMPACT DRIVER BRUSHLESS / FID 20-I BL WU5451673/ WU5451674 • 813545 • 05/2022 … meets all of the requirements of the listed directives.
Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within its intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention.
