Thank you for purchasing this ALCOM Telephone. We recommend you to read this manual and familiarize the functions of this unit before use.
ID information. b) Installation Open the battery cover on back of the unit. Insert 3 x AA batteries (1.5V) according to assigned direction. Close the battery cover. Using the coil cord connect the telephone with handset. Using the line cord connect the telephone to the telephone wall socket. NOTE: Do not mix different types of batteries. Operation Guide 1.
The cursor of day will blink, press UP/- or DOWN/+ button to adjust, press SET button to confirm and enter next step. The cursor of hour will blink, press UP/-or DOWN/+ button to adjust, press SET button to confirm and enter next step. The cursor of minute will blink, press UP/- or DOWN/+ button to adjust, press SET button to confirm, then finish the setting. After you finish above setting, LCD will show the set date and time and show the next available menu. Press DEL button to exit.
and so on. LCD will show the next available menu. Press DEL button to exit. c) Set the PABX code On-hook state, press SET button once, SEt 1 dAtE will show in the LCD. press UP/- button twice, SEt 3 PCOdE will show in the LCD. Press SET button to confirm, PCOdE - - will display, and the first cursor “- -“ will blink Note: The previous PABX code will be shown if you have set before.
will show in the LCD. Press UP/- button six times, SEt 7 ALErt will show in the LCD. Press SET button to confirm, 1 00-00 OFF will display. (1 indicates the first group alarm you can set up to 3 group alarm,00-00 indicates the alarm time, OFF indicates ALARM status) Press UP/- or DOWN/+ button to choose group then press SET button, first digit will blink, choose the digit by pressing UP/- or DOWN/+ button then press SET to continue to next digit.
Check the incoming calls On-hook status, press UP/- or DOWN/+ button to review the call number, date and time. If you hold the UP/- or DOWN/+ button for 3s, it will review quickly. Press DEL button once if you need to delete the current number. Hold the DEL button for 4s if you need to delete the all incoming calls. Call back an Incoming call When reviewing the incoming calls if you need to call the displayed number press ARD button once and the phone will dial to that number.
If you hold the UP/- button for 3s to review quickly. Press DEL button once if you need to delete the current number. Hold the DEL button for 3s if you need to delete the all outgoing calls. Call back an Outgoing call When reviewing the outgoing calls if you need to call back the displayed number press ARD button once and the phone will dial to that number. 4. Pre-dial Number Menu In On-hook state, press the telephone number that you want to dial.
You can use the calculator function in off-hook or on-hook State. In On-hook or in the talking status, press CAL button to enter the calculator function. During the calculator mode, press CAL button once to clear all data, Press DEL button to exit the calculator mode. The phone will auto exit the calculator mode if there is an incoming call and the LCD will show the new incoming call number.
button for 3s can delete all caller ID or outgoing calls including the VIP numbers. When you review the VIP number, press the PAUSE/VIP button to make the VIP number in unlock state, and the lock symbol will disappear from the LCD. 8. Redial, Flash & Pause Functions When you get a busy line, press FLASH to get a new dial tone. Press FLASH button to answer call waiting line. (second call) press FLASH button again to get back to the first line.
10. Dial Lock The unit provides Dial lock protection, the user can set the lock to different settings according to the colour position and functions as stated below. Red: No calls can be dialed out. Green:Telephone numbers starting with “0” cannot be dialed out, it means you cannot make an IDD call starting with “0”in this case. Yellow: Allows to make any call (key pad unlocked). 11. Auto redial function When dialing, if the line is busy, you could use this function to auto-redial the number.
In On-hook state, press SET button once, SEt 1 dAtE will show in the LCD. press UP/- button four times , SEt 5 P- t will show in the LCD. Press set button again and tONE will show in the display. Press UP/- or DOWN/+ to choose TONE or PULSE. Press SET button to confirm. LCD will show the next available menu. Press DEL button to exit. b) Set Anti-parallel Dial protection If this function is set all parallel phones connected with the same telephone line will not be able to dial out.
display. Press UP/- or DOWN/+ to choose ALAr OFF or ALAr ON. Press SET button to confirm.LCD will show the next available menu. Press DEL button to exit. FREQUENTLY ASKED QUESTIONS 1. NO TONE Please check all the lines connections, and ensure all the connections are proper. 2. CAN NOT MAKE/DIAL A CALL Please check the lock position and ensure Keys are unlocked. 3. NOISE Please check if the line cord or wall plug is moistured. 4.
b. Check if the battery has not drained and it has power. c.Check if an apparatus is connected between unit and Telephone line. (Example micro filters used in an ADSL line) If the unit still does not work properly, disconnect all the telephone cords, remove the batteries, after 5 minutes, reload batteries, insert the telephone line. The unit will get a reset. Start using the unit.
