Enforcer 3 User Manual AlcoLimit Breathalysers Pty. Ltd. P.O. Box 1106, Manly, NSW, 1655 Ph: 1300 667 661 www.alcolimit.com.
Enforcer 3 pg-2
Enforcer 3 IMPORTANT INFORMATION If you do not follow the instructions for use your test results may be inaccurate and your warranty may become void. IMPORTANT NOTE: YOU MUST WAIT AT LEAST 20 MINUTES AFTER YOUR LAST ALCOHOLIC DRINK BEFORE USING ALCOLIMIT Enforcer 3 OTHERWISE INACCURATE READINGS OF YOUR BLOOD ALCOHOL LEVEL WILL BE DISPLAYED ON THE SCREEN. PARTS OF YOUR BREATHALYSER AlcoLimit's Flow Control Technology checks the flow rate of your breath.
Enforcer 3 SPECIFICATIONS Usage Sensor Type Accuracy Range Display Usage Monitor Warm-up time Breath Sampling Time Time Between Retests Housing Weight Power Source Power Usage Dimensions Warranty Recalibration Mouthpieces Personal / Professional Semi-conductor Alcohol Sensor with Gas Flow Sensor built-in AS3547 Certified accuracy Calibrated to Australian & NZ legal limit 0.000 – 0.400g / 100mL LED with Backlight Cumulative test counter on start-up < 20 seconds 3 seconds (approx.
Enforcer 3 USAGE Turning on the power First, place 2xAA batteries (supplied) into your ALCOLIMIT Enforcer 3 in the correct direction as marked on the battery cover. Be sure to use high quality alkaline batteries (preferably Duracell). We recommend removing the batteries while the unit is in storage to prevent them going flat. High quality 1.5V Alkaline batteries must be used. Rechargeable batteries will not work as they are a lower voltage.
Enforcer 3 Blow one consistent deep breath into the sensor. There will be a continual long beep while you are blowing. Once your ALCOLIMIT Enforcer 3 has received enough airflow you will hear a double beep signaling you to stop. If inadequate airflow is received, the word will appear on the screen. Do not block the air hole on the opposite side of the mouthpiece while testing as this will affect the airflow.
Enforcer 3 DISPLAY & INTERPRETATION Result Type Negative Caution Digital Display (0.000-0.019%BAC) (0.020-0.049%BAC) Positive (0.050%BAC and above) In Normal mode readings above 0.400%BAC will be displayed as 0.400%BAC. This device is a 0.050%BAC device (0.050%BAC is equal to 0.05grams of alcohol per 100ml of blood). Australian Customers: The Australian drink driving cutoff for people on a full license is 50mg per 100ml of blood. This equates to 0.050%BAC. This is current as at October 2015.
Enforcer 3 TROUBLESHOOTING GUIDE Symptom Unit turns on and counts down then turns itself off Solution Not enough power - replace batteries Not enough power - replace batteries Unit doesn’t power up at all Check batteries are new and in the correct direction +/Recalibration is required Recalibration is required Inadequate airflow received. Keep blowing until you receive a double beep Readings are inaccurate Unit has timed out. You need to restart.
Enforcer 3 WARNINGS (Please read carefully) • • • • • • • • • • • Closed rooms with poor ventilation, pollution, smoke or air conditioning may delay the time for resetting between tests. Not waiting at least 20 minutes after your last alcoholic drink will cause inaccurate readings, and if you continue to misuse ALCOLIMIT Enforcer this way you will damage the sensor beyond repair (not covered under warranty).
Enforcer 3 RECALIBRATION The calibration period of ALCOLIMIT Enforcer is 30 days. For professional use we recommend recalibration every 1-3 months and for personal use every 3-12 months. Recalibration is required because alcohol residue builds up on the sensor and this must be cleaned because it affects the accuracy of the device over time. The sensor needs to be cleaned professionally. Do not try and clean it yourself as you will damage the sensor and the device will not work properly.
Enforcer 3 Professional Recalibration Costs and Procedure: Recalibration costs $45 AUD/approx. $55NZD and includes return postage to you within Australia and NZ via Australia Post Express. Post your ALCOLIMIT unit to : AlcoLimit Breathalysers Pty. Ltd. Recalibration Dept. P.O. Box 1106 Manly, N.S.W. 1655 When posting your ALCOLIMIT Enforcer to us you are advised to send it Registered Mail for tracking purposes. Australia Post sells a padded bag size 0 which fits ALCOLIMIT Enforcer perfectly.
Enforcer 3 WARRANTY Manufacturer warrants for one calendar year the product to be free from defects in workmanship or materials (excluding calibration) in normal service from the date of purchase. Manufacturer’s obligation under this warranty is limited to replacing or repairing the unit if returned along with proof of purchase. This warranty is void if unit has been tampered with, misused, dropped, maliciously damaged or used for any purpose other than that intended.
Enforcer 3 ADDITIONAL PRODUCTS AND ACCESSORIES Enforcer 2 Breathalyser Precise, durable and portable. Includes fast mode for rapid testing of large volumes of people. (ALCO-007) - 2 decimal place accuracy - Range of 0.00-0.04%BAC - Calibrated for the Aust. & NZ Legal Limit Mouthpieces Individually wrapped, disposable mouthpieces suitable for personal and professional use.
Enforcer 3 pg-14
Enforcer 3 pg-15
Enforcer 3 RECALIBRATION SERVICE RECORD Date of Recalibration Service Details Technician For service records to be updated, please send your instructions with your breathalyser each time it is recalibrated. Alternatively, you may request a Calibration Certificate at a cost of $22 (recommended for workplaces).
