SPEED TOUCH PC ADSL PC Network Interface Card Installation Guide Microsoft Windows 95A, 98 and NT4.0 VERSION 2.1.
SPEED TOUCH PC ADSL PC Network Interface Card Installation Guide Microsoft Windows 95A, 98 and NT4.0 VERSION 2.1.
TABLE OF CONTENTS Introduction.......................................................................................................... 1 System Requirements........................................................................................... 1 Determining Your Service Type.......................................................................... 3 Technical Support................................................................................................ 3 Before Installation...................
Alcatel Speed Touch™ PC Installation Guide INTRODUCTION Congratulations! You’ll soon have the fastest connection available to the Internet – thanks to Alcatel’s Speed Touch PC. The Alcatel Speed Touch PC is an internal Asymmetric Digital Subscriber Line (ADSL) PC Network Interface Card (NIC), which conveniently plugs into your computer system. Alcatel’s Speed Touch PC connects directly to your telephone line via a standard RJ-11 connector and is fully plug-and-play compatible.
Alcatel Speed Touch™ PC Installation Guide On the desktop, right click My Computer. Then select Properties. The version number of the Microsoft Windows Operating System installed in your computer will be displayed. Refer to the following table for more detailed information. Windows Version System Description on System Properties Official Release Name (on Microsoft Web page) Win 95A 4.00.950A Windows 95 OSR1 Win 95B 4.00.950B Windows 95 OSR2 Win 98 4.10.1998 Window 98 Win 98A 4.10.
Alcatel Speed Touch™ PC Installation Guide DETERMINING YOUR SERVICE TYPE Contact your Internet Service Provider (ISP) for your service type and connection configuration.
Alcatel Speed Touch™ PC Installation Guide BEFORE INSTALLATION If you are installing PPPoA service for Win95A, 95B or Bridged Ethernet service for Win95A, you need to upgrade your Dial-Up Networking (DUN) application to version 1.3 or above. Please refer to Appendix A on how to upgrade your system’s DUN.
Alcatel Speed Touch™ PC Installation Guide TO INSTALL POINT TO POINT PROTOCOL OVER ATM SERVICE Win95A go to page 5 Win95B go to page 7 Win98, 98A go to page 9 NT 4.0 go to page 14 TO INSTALL BRIDGED ETHERNET SERVICE Win95A go to page 23 Win95B go to page 25 Win98, 98A go to page 27 NT 4.0 go to page 31 POINT TO POINT SERVICE FOR WINDOWS 95A 1. After installing the Alcatel Speed Touch PC card, power on the PC system. The Hardware Wizard will detect the card as a PCI Network Controller.
Alcatel Speed Touch™ PC Installation Guide NOTE: If you clicked Advanced, the Service Options window shows the Connection Address. Enter the service Connection Address, click OK. The previous Service Option window will appear, click Next. NOTE: During the installation process you may be asked to insert your Windows 95. Insert the Windows 95 CD into the CD drive and click OK. NOTE: If during the file copying process a file is reported as “not found” enter the path :\Win95 (e.g.
Alcatel Speed Touch™ PC Installation Guide POINT TO POINT SERVICE FOR WINDOWS 95B 1. After installing the Alcatel Speed Touch PC card, power-up the PC system. The Hardware wizard will detect the Alcatel Speed Touch PC as a PCI Network Controller, click Next 2. Insert the Alcatel Speed Touch PC Device Driver CD into the CD drive. Then click Other Locations. Note: If the driver is not detected, click Back, insert the Speed Touch PC disk, then click NEXT. 3.
Alcatel Speed Touch™ PC Installation Guide NOTE: If you clicked Advanced, the Service Options window shows the Connection Address. Enter the service Connection Address, click OK. The previous Service Option window will appear, click Next. Note: During the installation process you may be asked to insert your Windows 95. Insert the Windows 95 CD into the CD drive and click OK. 7. The Copying Files window will now appear. Enter :\WIN95 (e.g. D:\WIN95) and click OK. 8.
Alcatel Speed Touch™ PC Installation Guide POINT TO POINT SERVICE FOR WINDOWS 98, 98A 1. After installing the Speed Touch PC card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Then select Search for the best driver for your device. (Recommended), click Next. 3. Insert the CD labeled Alcatel Speed Touch PC Driver into your CD drive. 4.
Alcatel Speed Touch™ PC Installation Guide 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you clicked Advanced, the Service Options window shows the Connection Address. Enter the service Connection Address, click OK. The previous Service Option window will appear, click Next. 7. Additional files are copied from the Speed Touch PC disk to the hard drive.
Alcatel Speed Touch™ PC Installation Guide 11. After restarting the system, the Diagnostic Tools icon is active and monitoring connectivity. The Diagnostic Tools – found on the task bar – with blinking (or solid) Black or Green lights indicate a good connection. Diagnostic Tools with Red lights indicate a connection error or driver load error. Verify that the cable is properly connected to the data port of the service and Speed Touch PC card. 12. You must now make a dial-up network connection.
Alcatel Speed Touch™ PC Installation Guide 15. Make New Connection is complete. Click Finish. 16. The new connection will appear in the Dial-Up Networking window. 17. Double-click the My Connection icon to begin a Dial-Up session. 18. Enter the User Name and Password supplied by the Internet service provider. Click Connect. 19. The message Logging on to network confirms a valid user name, password, and VPN IP address. Please wait for the Connection Established window before proceeding.
Alcatel Speed Touch™ PC Installation Guide 20. The PPPoA service connection is now established. Click Close and the PPPoA icon appears on the task bar. Congratulations, you are done.
Alcatel Speed Touch™ PC Installation Guide POINT TO POINT SERVICE FOR WINDOWS NT 4.0 Note: To perform the installation logon as Administrator. Also the TCP/IP protocol must be installed prior to the driver installation. 1. At the desktop, double click My Computer, then double click Control Panel. 2. In the Control Panel window, double click the Network icon then select the Adapters tab. 3. Click Add (to add new adapters). 4. In the Select Network Adapter window click Have Disk. 5.
Alcatel Speed Touch™ PC Installation Guide TOUCH PC driver, Click OK. The system will copy the drivers to the hard drive. 7. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you clicked Advanced, the Service Options window shows the Connection Address. Enter the service Connection Address. Click OK. The previous Service Option window will appear, click next. 8.
Alcatel Speed Touch™ PC Installation Guide configuration. 12. Select the protocol (e.g. TCP/IP), if a protocol has not been loaded the Windows NT 4.0 CD will be required. Click OK. 13. The Network window will appear at the conclusion of the installation to confirm installation of the Alcatel SPEED TOUCH PC. 14. Click on Protocols tab and verify that the ADSL Management and Monitor Interface is present.
Alcatel Speed Touch™ PC Installation Guide 15. Still in the Network window, click on the Services tab to verify that the Remote Access Service is present. Click Close. Note: To review the Network window properties at any time, right-click the Network Neighborhood icon and select Properties. Note: If no previous network devices have been installed, then the Network Neighborhood icon will not be present on the desktop. To open the Network window, double-click My Computer then Control Panel then Network. 16.
Alcatel Speed Touch™ PC Installation Guide 17. After the system restarts the Diagnostic Tools icon will appear on the task bar. When the Speed Touch PC card is connected to the ADSL data port, both panels of the icon will appear black signifying an ADSL connection. 18. To begin a dial-up connection, double-click My Computer, then double-click Dial-Up Networking. 19. If this is the first dial-up connection created enter an area code (e.g. 408) for your region, then click Close.
Alcatel Speed Touch™ PC Installation Guide 22. When the Server window appears click Next. 23. The Dial-Up Networking window prompts for the phone number of the dial-up server. Unless instructed to enter a phone number by the ISP, enter zero “0” Still at the Dial-Up Networking window, click More. 24. The Edit Phonebook Entry window appears. Select the Security tab and verify that “Accept only Microsoft encrypted authentication ” is selected. Click OK.
Alcatel Speed Touch™ PC Installation Guide Note: The text “Verifying username and password…” will be displayed while logon authentication takes place. Note: If this screen persists and a connection logon error is reported, confirm that the correct Username and Password are entered and try the connection again. Also verify that the connection address is correct. 26. This window is displayed at the completion of a successful DialUp logon. Choose a display behavior and click OK to close.
Alcatel Speed Touch™ PC Installation Guide PPPoA ADSL NETWORK CONNECTION Note: This section is for Win95A, 95B and 98 users only. 1. Double click the My Computer icon on the desktop. Then double click the Dial-Up Networking icon. The Dial-Up Networking window will appear. Note: Another dialog window may prompt for the entry of the Area Code if this is a first time Network connection. Enter the Area code and click OK. 2. Double-click on the Make New Connection icon. 3. Enter the connection name (e.g.
Alcatel Speed Touch™ PC Installation Guide 5. The new connection will appear in the Dial-Up Networking window. Double-click the My Connection icon to begin a DialUp session. 6. Enter the User Name and Password supplied by the Internet service provider. Then click Connect. Note: The Virtual Private Network server name (or IP address) has been previously entered. 7. The Connection window reports the status of a connection. The message Logging on to network confirms a valid connection.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET SERVICE FOR WINDOWS 95A 1. After installing the Speed Touch PC card, power on the PC system. The Hardware Wizard will detect the Speed Touch PC as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option. 2. Insert the Alcatel Speed Touch PC Device Driver CD into the drive. 3. The Install From Disk window appears. Enter the :\1483w9x (e.g. D:\1483w9x), then click OK. 4.
Alcatel Speed Touch™ PC Installation Guide NOTE: If during the file copying process a file is reported as “not found” enter the path :\Win95 (e.g. D:\Win95) 5. At the conclusion of the Speed Touch PC driver installation, the Diagnostic Tool icon will appear disabled on the task bar. You must now Restart the PC system to complete the installation; the Diagnostic Tool will then become active. 6. Proceed to Bridged Ethernet ADSL Service Configuration; page 29.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET SERVICE FOR WINDOWS 95B 1. After installing the Speed Touch PC card, power-up the PC System. 2. The Hardware wizard will detect the Alcatel Speed Touch PC as a PCI Network Controller, click Next. Insert the Alcatel Speed Touch PC Driver CD into the CD-ROM drive. Click Other Locations. 3. When Select Other Location window appears, enter :\1483w9x (e.g. D:\1483w9x) and click OK. 4.
Alcatel Speed Touch™ PC Installation Guide 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you clicked Advanced, the Service Options window shows the Connection Address. Enter the service Connection Address, click OK. The previous Service Option window will appear, click Next.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET FOR WINDOWS 98, 98A 1. After installing the Speed Touch PC card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Then select Search for the best driver for your device. Click Next. 3. Insert the CD labeled Alcatel Speed Touch PC Driver into your CD-ROM drive. 4.
Alcatel Speed Touch™ PC Installation Guide 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. NOTE: If you click Advanced, the Connection Address window appears. Enter the Service connection address, click OK. The previous Service Options window will appear, click Next. NOTE: If prompted, insert your Windows 98 CD-ROM into the drive and click OK. 7.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET ADSL SERVICE CONFIGURATION This section describes how to configure the ADSL network service when your PC is running Microsoft Windows 95A, 95B, 98, 98A. 1. Double click My Computer, Control Panel, and then Network. 2. In the Network window, select the Configuration tab. Scroll through the loaded network components list. Highlight the TCP/IP->Alcatel SPEED TOUCH PC and click Properties.
Alcatel Speed Touch™ PC Installation Guide 6. Select the SGateway tab. Enter your gateway information into the New gateway box and click Add. If you have more than one gateway numbers, repeat this step NOTE: Please refer to ADSL System Work Sheet, or consult your ISP for the TCP/IP Properties. 7. Select DNS Configuration tab. Select the Enable DNS option. 8. Enter your host name into Host: box. 9. Enter your domain name into Domain: box. 10.
Alcatel Speed Touch™ PC Installation Guide BRIDGED ETHERNET FOR WINDOWS NT 4.0 Note: To perform the installation logon as Administrator. TCP/IP protocol must be installed prior to the driver installation. At the Network window select the Protocols tab and verify that the TCP/IP is present. 1. At the desktop, double click My Computer, double click Control Panel, double click Network and then select the Adapters tab of the Network window. 2. Click Add (to add new adapters). 3.
Alcatel Speed Touch™ PC Installation Guide 5. The Select OEM Option window will find the Alcatel SPEED TOUCH PC card. Click OK. The system will copy the drivers to the hard drive. 6. When the Service Option window appears, click Next for the default installation. For Advanced settings, please consult your ADSL service provider for detailed information. Note: If you click Advanced, the Service Options window appears. Enter the service Connection Address, click OK.
Alcatel Speed Touch™ PC Installation Guide information. When not connecting to a DHCP server, enter the IP address (e.g. 192.168.4.39). 8. Enter the Subnet Mask (e.g. 255.255.255.0). 9. Enter the Default Gateway address. Note: Consult your ISP for the TCP/IP Properties. 10. Select the DNS Configuration tab and enter the Host Name (e.g. speed_touch) 11. Then enter the Domain Name (e.g. pacbell.net) Note: Use the DNS Service Search and Domain Sufix Search to locate the Host Name and Domain.
Alcatel Speed Touch™ PC Installation Guide illustrative differences, the process for editing the IP address settings is the same for Windows NT 4.0 and Windows 95/98. 2. At the desktop, double click My Computer, then double click Control Panel to view the contents of the control panel. In the Control Panel window, double click the Network icon. Note: The Network window shortcut is a right-click the Network Neighborhood on your desktop then left-click Properties. 3.
Alcatel Speed Touch™ PC Installation Guide 8. Enter the Host Name (e.g. speed_touch) and Domain (e.g. pacbell.net). Note: To enter the Domain search (DNS) entries, click Add then enter the address. Click Add to save the address. Repeat the process for additional DNS entries. 9. Click OK to update the changes.
Alcatel Speed Touch™ PC Installation Guide DIAGNOSTIC TOOLS The diagnostic tools allow the user to monitor the ADSL connectivity, setup the service connection address, and run diagnostic tests. The Diagnostic Tools icon is displayed on the task bar as shown. Maximum transfer rate Maximum receiving rate By positioning the mouse cursor over the icon, a summary of the ADSL connection status is displayed e.g. upstream and downstream line rates. The Diagnostic Tools icon consists of two lights side by side.
Alcatel Speed Touch™ PC Installation Guide APPENDIX A - UPGRADE MICROSOFT DUN VERSION 1.3 This section explains how to upgrade Microsoft’s Dial-Up Networking (DUN) application. You can download the DUN application from Microsoft’s Web page and install it into your system. Please follow the instruction below. 1. Access the Microsoft Web site at http://www.microsoft.com. 2. In the Contents frame, select Free Downloads. 3. Scroll to Support Drivers, Patches and Service Packs and select Window 95 Updates.
Alcatel Speed Touch™ PC Installation Guide APPENDIX B – VERIFYING DIAL-UP NETWORKING (DUN) STATUS 1. It is possible to have Dial-Up Networking (DUN) version 1.2B or above, but not have the Dial-Up Networking components loaded in the Windows environment. This procedure is for determining the status of DUN on the PC system. 2. At the task bar click Start, Settings, Control Panel and double-click on Add/Remove Programs. 3.
Alcatel Speed Touch™ PC Installation Guide APPENDIX C – REMOVING SPEED TOUCH PC DRIVERS WINDOWS 95, 98 1. To Delete Alcatel Speed Touch PC drivers; on the desktop, rightclick on My Computer, then click Properties, then click on the Device Manager tab, then double click Network adapters. 2. Select the Alcatel SPEED TOUCH PC, then click on the Remove button. 3. A warning message “You are about to remove this device from your system” will appear.
Alcatel Speed Touch™ PC Installation Guide 3. A warning message will inform you that a component is about to be removed. Click Yes. 4. Once the Alcatel SPEED TOUCH PC is removed from the adapter list, click Close. 5. The PC system must be restarted for the changes to take effect. Click Yes.
Alcatel Speed Touch™ PC Installation Guide APPENDIX D: Power Requirements • .75A Max @ +5V ± 5%, 0.
Alcatel Speed Touch™ PC Installation Guide APPENDIX E: Copyright © 1999, Integrated Telecom Express, Inc. All rights reserved. This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without the written consent of Integrated Telecom Express, Inc. Speed Touch PC is a trademark of Alcatel. All other product names are trademarks and or registered trademarks of their respective companies.
