Part No. 060322-10 Rev. K March 2015 OmniSwitch AOS Release 7 Transceivers Guide www.alcatel-lucent.
This user guide contains transceiver specifications and compatibility information for the OmniSwitch AOS Release 7 and supported platforms. The information described in this guide is subject to change without notice. Attention: Use of any transceivers other than those part numbers listed in the Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for proper performance and may result in voiding the warranty for the affected platforms.
Contents About This Guide ........................................................................................................... v Supported Platforms ........................................................................................................... v Who Should Read this Manual? ........................................................................................ vi When Should I Read this Manual? ....................................................................................
Contents iv OmniSwitch AOS Release 7 Transceivers Guide March 2015
About This Guide This OmniSwitch AOS Release 7 Transceivers Guide provides specifications and compatibility information for the supported OmniSwitch transceivers for all OmniSwitch AOS Release 7 Products.
Who Should Read this Manual? About This Guide Who Should Read this Manual? The audience for this user guide is network administrators and IT support personnel who need to provide network connectivity using SFP, SFP+, and QSFP+ transceivers. When Should I Read this Manual? Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are ready to provide connectivity using the supported transceivers.
About This Guide Documentation Roadmap Documentation Roadmap The OmniSwitch user documentation suite was designed to supply you with information at several critical junctures of the configuration process.The following section outlines a roadmap of the manuals that will help you at each stage of the configuration process. Under each stage, we point you to the manual or manuals that will be most helpful to you.
Documentation Roadmap About This Guide Anytime The OmniSwitch AOS Release 7 CLI Reference Guide contains comprehensive information on all CLI commands supported by the switch. This guide includes syntax, default, usage, example, related CLI command, and CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can be consulted anytime during the configuration process to find detailed and specific information on each CLI command.
About This Guide Related Documentation Related Documentation The following are the titles and descriptions of all the OmniSwitch user manuals: • OmniSwitch 10K Getting Started Guide Describes the hardware and software procedures for getting an OmniSwitch up and running. Also provides information on fundamental aspects of OmniSwitch software architecture.
Technical Support About This Guide Technical Support An Alcatel-Lucent service agreement brings your company the assurance of 7x24 no-excuses technical support. You’ll also receive regular software updates to maintain and maximize your Alcatel-Lucent product’s features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners.
1 Small Form-Factor Pluggables (SFP/SFP+/QSFP+) OmniSwitch Series switches use both copper-based and fiber-based optical Small Form Factor Pluggable transceivers. These transceivers are fully hot-swappable and are available for both short-reach and longreach applications. Copper-based and fiber-based optical transceivers can be mixed on the same module. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported transceivers.
SFP MSA Specification Small Form-Factor Pluggables (SFP/SFP+/QSFP+) The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP housing cage. The connector provides the interface for the hot pluggable SFP module.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Transceiver Installation and Removal Transceiver Installation and Removal Follow the instructions below for the appropriate transceiver type. ESD Caution: Before handling the module, you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the chassis.
Transceiver Installation and Removal Small Form-Factor Pluggables (SFP/SFP+/QSFP+) To install, align the transceiver with the transceiver slot on the NI module, as shown. Be sure that the bail wire delatch is in the up, or closed position. Slide the transceiver straight into the slot until the module clicks firmly into place. To remove, you must first pull down on the bail wire delatch. Grip the wire delatch while it is in this open position and carefully pull the transceiver straight out of the slot.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) To install, align the transceiver with the transceiver slot on the NI module, as shown. Carefully slide the transceiver back until it clicks into place; this is an indication that the connectors are firmly seated. Transceiver Installation and Removal Network Interface (NI) Module QSFP+ Transceiver To remove, use the rubber or metal ejector handle and pull transceiver straight out and away from the NI module.
Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Gigabit Ethernet Transceivers SFP-GIG-SX Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9.0 to -3 dBm Receiver Sensitivity -20 dBm Transmission Distance ~300 m on 62.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers (cont.) SFP-GIG-LH70 Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Gigabit Ethernet Transceivers (cont.) SFP-GIG-T Gigabit SFP Copper Transceiver. Connector Type RJ-45 Standards Supported 802.3z, SFP MSA Connections supported 10/100/1000Base-T Cable Type CAT5, CAT5e, CAT6 Transmission Distance 100 m Digital Diagnostic Monitoring Not Supported SFP-GIG-EXTND Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers SFP-100-BX20LT Bi-Directional SFP Optical Transceiver. Connector Type SC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Bi-directional Ethernet Transceivers (cont.) SFP-100-BXLC-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont.) SFP-GIG-BX-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.
100 FX Ethernet Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 100 FX Ethernet Transceivers SFP-100-LC-MM SFP Optical Transceiver. Connector Type LC Standards Supported 802.3u, SFP MSA Connections supported 100Base-FX Fiber Type MMF Wavelength 1310 nm Optical Power Output -19 to -14 dBm on 62.5/125µm -22 to 14 dBm on 50/125µm Transmission Distance ~2 km on 62.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 100 FX Ethernet Transceivers 100 FX Ethernet Transceivers (cont.) SFP-100-LC-SM40 SFP Optical Transceiver. Connector Type LC Standards Supported 802.
CWDM Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) CWDM Gigabit Ethernet Transceivers . SFP-GIG-CWD Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications. Connector Type LC Standards Supported 802.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 10-Gigabit SFP+ Transceivers 10-Gigabit SFP+ Transceivers SFP-10G-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.3 to -3.0 dBm Receiver Sensitivity -11.
10-Gigabit SFP+ Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) SFP-10G-ER 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3ae Connections supported 10GBase-E Fiber Type SMF Wavelength 1550 nm Optical Power Output -4.7 to 4.0 dBm Receiver Sensitivity -14.1 dBm Transmission Distance ~ 40 km Operating Temperature -5 ºC to 70 ºC Maximum Power Consumption 1.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 10-Gigabit SFP+ Transceivers SFP-10G-LRM 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3aq Connections supported 10GBase-LRM Fiber Type MMF Wavelength 1310 nm Optical Power Output -4.5 to 1.5dBm Receiver Sensitivity -6.
10-Gigabit SFP+ Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) SFP-10G-GIG-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3-2005 Connections supported 10GBase-SR/SW, 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -5 to -1 @ 10G -9.5 to -1dBm @ 1G Receiver Sensitivity -11.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 40-Gigabit QSFP+ Transceivers 40-Gigabit QSFP+ Transceivers CAUTION - CLASS 1M LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. QSFP-40G-SR Four channel 40-Gigabit QSFP+ Optical Transceiver. Connector Type MPO Standards Supported 802.3ba, QSFP+ MSA Connections supported 40GBase-SR4 Fiber Type MMF Wavelength 850 nm Optical Power Output -7.6 to +2.4 dBm Receiver Sensitivity -5.
40-Gigabit QSFP+ Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) QSFP-40G-C Four channel 40-Gigabit QSFP+ Direct Attach Copper Cable Connector Type Direct Attached Copper Standards Supported 802.3ba, QSFP+ MSA Cable Length 1m, 3m, 7m1,2 Wire Gauge 26AWG Bend Radius 1.69 in. Digital Diagnostic Monitoring Not Supported 1. Check for availability of lengths. 2. The QSFP-40G-C7 (7m) cable has been verified for proper operation when connected between OmniSwitch products.
Small Form-Factor Pluggables (SFP/SFP+/QSFP+) 40-Gigabit QSFP+ Transceivers QSFP-4X10G-C Four channel 40-Gigabit QSFP+ Direct Attached Copper Splitter Cable.
Fibre Channel Transceivers Small Form-Factor Pluggables (SFP/SFP+/QSFP+) Fibre Channel Transceivers SFP-FC-SR Triple-speed SFP+ Fibre Channel optical transceiver. Connector Type LC Standards Supported FC-PI-4 Connections supported Auto-sensing 2G, 4G, 8G Fiber Type MMF Wavelength 850 nm Average Optical Power Output Transmission Distance 1 -8.
Transceiver Compatibility Matrix 2 In This Chapter Transceiver Compatibility Matrix In This Chapter The following sections document the transceiver configurations and minimum release required for support on the OmniSwitch. Compatibility specifications in this chapter include: • OmniSwitch 10K . See “OmniSwitch 10K Series Compatibility” on page 2-24 • OmniSwitch 6900 .
OmniSwitch 10K Series Compatibility Transceiver Compatibility Matrix OmniSwitch 10K Series Compatibility The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 10K Series: Transceiver OS10KGNI-U48 OS10K-XNI U32/U16 OS10K-QNI U4/U8 SFP-GIG-SX 7.1.1 7.1.1 Not Supported SFP-GIG-LX 7.1.1 7.1.1 Not Supported SFP-GIG-LH40 7.1.1 7.1.1 Not Supported SFP-GIG-LH70 7.1.1 7.1.1 Not Supported SFP-GIG-CWD 7.1.1 7.1.
Transceiver Compatibility Matrix OmniSwitch 6900 Series Compatibility OmniSwitch 6900 Series Compatibility The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 6900 Series: Transceiver OS6900X20/X40 OS6900-Q32 XNI-U4/U12 HNI-U6 QNI-U3 XNI-U12E SFP-GIG-SX 7.2.1 N/S 7.2.1 7.2.1.R02 N/S 7.3.3 SFP-GIG-LX 7.2.1 N/S 7.2.1 7.2.1.R02 N/S 7.3.3 SFP-GIG-LH40 7.2.1 N/S 7.2.1 7.2.1.R02 N/S 7.3.3 SFP-GIG-LH70 7.2.
OmniSwitch 6900 Series Compatibility page 2-26 Transceiver Compatibility Matrix OmniSwitch AOS Release 7 Transceivers Guide March 2015
