060210-00 Rev. N January 2013 OmniSwitch AOS Release 6 Transceivers Guide www.alcatel-lucent.
This user guide contains SFP and XFP transceiver specifications and compatibility information for the OmniSwitch 6400, 6850E, 6855 and 9000E Series of switches . The information described in this guide is subject to change without notice. Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP Compatibility Matrices is prohibited.
Contents About This Guide ........................................................................................................... v Supported Platforms ........................................................................................................... v Who Should Read this Manual? ........................................................................................ vi When Should I Read this Manual? ....................................................................................
Contents XFP Transceiver Installation and Removal ..................................................................1-34 10-Gigabit Ethernet Transceivers .................................................................................1-35 Chapter 4 SFP Compatibility Matrix ........................................................................................ 1-39 OmniSwitch 9000E Series ............................................................................................
About This Guide This OmniSwitch Transceivers Guide provides specifications and compatibility information for the supported OmniSwitch SFP and XFP transceivers for all OmniSwitch AOS 6 Release Products. Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for proper performance and may result in voiding the warranty for the affected platforms.
Who Should Read this Manual? About This Guide Who Should Read this Manual? The audience for this user guide is network administrators and IT support personnel who need to provide network connectivity using SFP or XFP transceivers on an OmniSwitch. When Should I Read this Manual? Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are ready to provide connectivity using the supported transceivers.
About This Guide How is the Information Organized? How is the Information Organized? Chapters in this guide are broken down by transceiver type, SFP or XPF. Additional sub-sections are provided for the various types of transceivers. Specification Information. Each transceiver has an associated table providing individual specifications for all supported transceivers. Compatibility Information.
Documentation Roadmap About This Guide Stage 3: Integrating the Switch Into a Network Pertinent Documentation: Network Configuration Guide Advanced Routing Configuration Guide When you are ready to connect your switch to the network, you will need to learn how the OmniSwitch implements fundamental software features, such as 802.1Q, VLANs, Spanning Tree, and network routing protocols.
About This Guide Related Documentation Related Documentation The following are the titles and descriptions of all the related OmniSwitch AOS Release 6 user manuals: • OmniSwitch 6400 Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6400 shipment. Also provides information on the initial configuration of the switch.
Related Documentation About This Guide (Ethernet and VLAN configuration), Layer 3 information (routing protocols, such as RIP), security options (authenticated VLANs), Quality of Service (QoS), and link aggregation. • OmniSwitch AOS Release 6 Advanced Routing Configuration Guide Includes network configuration procedures and descriptive information on all the software features and protocols included in the advanced routing software package. Chapters cover multicast routing (DVMRP and PIM-SM), and OSPF.
About This Guide Product Documentation Product Documentation Some products are shipped with documentation included on a User Manual CD that accompanies the switch. This CD also includes documentation for other Alcatel-Lucent data enterprise products. All products are shipped with a Product Documentation Card that provides details for downloading documentation for all OmniSwitch and other Alcatel-Lucent data enterprise products.
Technical Support page xii About This Guide OmniSwitch Transceivers Guide January 2013
1 Small Form-Factor Pluggables (SFPs) OmniSwitch Series switches use both copper-based and fiber-based optical Small Form Factor Pluggable (SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. Copper-based and fiber-based optical SFPs can be mixed on the same module. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported SFP transceivers.
SFP MSA Specification Small Form-Factor Pluggables (SFPs) SFP MSA Specification The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP housing cage. The connector provides the interface for the hot pluggable SFP module.
Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal SFP Transceiver Installation and Removal Follow the instructions below for the appropriate SFP type. ESD Caution: Before handling the module, you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the chassis. If your chassis provides a grounding lug, this can be used.
SFP Transceiver Installation and Removal Small Form-Factor Pluggables (SFPs) To install, align the transceiver with the transceiver slot on the NI module, as shown. Be sure that the bail wire delatch is in the up, or closed position. Slide the transceiver straight into the slot until the module clicks firmly into place. To remove, you must first pull down on the bail wire delatch. Grip the wire delatch while it is in this open position and carefully pull the transceiver straight out of the slot.
Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers SFP-GIG-SX Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9.5 to -4 dBm Receiver Sensitivity -17 dBm Transmission Distance ~275 m on 62.
Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers (cont.) SFP-GIG-LH70 Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-LH70 Fiber Type SMF Wavelength 1550 nm Optical Power Output 0 to +5 dBm Receiver Sensitivity -22 dBm Transmission Distance ~70 km Operating Temperature 0ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-GIG-LH40 Gigabit SFP Optical Transceiver.
Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers (cont.) SFP-GIG-EXTND Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 1310 nm Optical Power Output - Receiver Sensitivity - Transmission Distance ~2 km Operating Temperature 0ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-GIG-T Gigabit SFP Copper Transceiver.
Dual-Speed Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Dual-Speed Ethernet Transceivers SFP-DUAL-MM Dual-Speed SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, 802.3ah, SFP MSA Connections Supported 100Base-FX, 1000Base-LX Fiber Type MMF Wavelength 1310 nm Average Power Output 100Base-FX: -20 to -14 dBm 1000Base-LX: -11.
Small Form-Factor Pluggables (SFPs) Dual-Speed Ethernet Transceivers SFP-DUAL-BX-D Dual-Speed Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000BASE-BX10-D Fiber Type SMF Wavelength Transmit: 1550 nm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -18.
Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers SFP-100-BX20LT Bi-Directional SFP Optical Transceiver. Connector Type SC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont.) SFP-100-BXLC-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers (cont.) SFP-GIG-BX-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.
Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont.) SFP-GIG-BX-D20 Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers (cont.) SFP-GIG-BX-D40 Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers 100 FX Ethernet Transceivers SFP-100-LC-MM SFP Optical Transceiver. Connector Type LC Standards Supported 802.3u, SFP MSA Connections supported 100Base-FX Fiber Type MMF Wavelength 1310 nm Optical Power Output -19 to -14 dBm on 62.5/125µm -22 to -14 dBm on 50/125µm Transmission Distance ~2 km on 62.
100 FX Ethernet Transceivers Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers (cont.) SFP-100-LC-SM40 SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Small Form-Factor Pluggables (SFPs) CWDM Gigabit Ethernet Transceivers CWDM Gigabit Ethernet Transceivers . SFP-GIG-CWD Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications. Connector Type LC Standards Supported 802.
10-Gigabit SFP+ Transceivers Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers SFP-10G-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.3 to -1.3 dBm Receiver Sensitivity -11.1 dBm Transmission Distance ~ 300 m Operating Temperature 0ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-10G-LR 10-Gigabit SFP+ Optical Transceiver.
Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers SFP-10G-ER 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3ae Connections supported 10GBase-E Fiber Type SMF Wavelength 1550 nm Optical Power Output -4.7 to 4.0 dBm Receiver Sensitivity -14.1 dBm Transmission Distance ~ 40 km Operating Temperature 0ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-10G-LRM 10-Gigabit SFP+ Optical Transceiver.
10-Gigabit SFP+ Transceivers Small Form-Factor Pluggables (SFPs) SFP-10G-GIG-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3-2005 Connections supported 10GBase-SR/SW, 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -5 to -1 @ 10G -9.5 to -1dBm @ 1G Receiver Sensitivity -11.
Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers SFP-10G-C 10-Gigabit SFP+ Copper Transceiver. Connector Type Direct Attached Standards Supported 802.3ae, SFF-8431 Cable Length 1m, 3m, 7m1 Wire Gauge 24AWG Bend Radius 1.25 in. Digital Diagnostic Monitoring Not Supported 1 Check for availability of lengths.
In This Chapter Industrial Small Form Factor Pluggables (iSFPs) 2 Industrial Small Form Factor Pluggables (iSFPs) OmniSwitch Series switches use both copper-based and fiber-based optical Industrial Small Form Factor Pluggable (SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. Additionally, Industrial SFPs are designed to operate at an increased temperature range. Copper-based and fiber-based optical SFPs can be mixed on the same module.
Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers Industrial Gigabit Ethernet Transceivers iSFP-GIG-SX Industrial Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9.5 to -3.5 dBm Receiver Sensitivity -18 dBm Transmission Distance ~275 m on 62.
Industrial Gigabit Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers (cont.) iSFP-GIG-LH70 Industrial Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers iSFP-GIG-T Industrial Gigabit SFP Copper Transceiver. Connector Type RJ-45 Standards Supported 802.3z, SFP MSA Connections supported 10/100/1000Base-T Cable Type CAT5, CAT5e, CAT6 Transmission Distance !100 m Operating Temperature -40ºC to 85ºC Digital Diagnostic Monitoring Not Supported iSFP-GIG-EZX Industrial Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Industrial Bi-directional Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial Bi-directional Ethernet Transceivers iSFP-100-BX-D Industrial Bi-Directional SFP Optical Transceiver. Connector Type SC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Industrial Small Form Factor Pluggables (iSFPs) Industrial Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont.) iSFP-100-BXLC-D Industrial Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA, ITU-T G.
Industrial Bi-directional Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) iSFP-GIG-BX-D Industrial Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.
Industrial Small Form Factor Pluggables (iSFPs) Industrial 100 FX Ethernet Transceivers Industrial 100 FX Ethernet Transceivers iSFP-100-MM Industrial SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Industrial 100 FX Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial 100 FX Ethernet Transceivers (cont.) iSFP-100-SM40 Industrial SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Industrial Small Form Factor Pluggables (iSFPs) Industrial 10-Gigabit SFP+ Transceivers Industrial 10-Gigabit SFP+ Transceivers iSFP-10G-LR Industrial 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-LR Fiber Type SMF Wavelength 1310 nm Optical Power Output -8.2 to 0.5 dBm Receiver Sensitivity -10.
Industrial 10-Gigabit SFP+ Transceivers Industrial Small Form Factor Pluggables (iSFPs) iSFP-10G-C 10-Gigabit SFP+ Copper Direct Attached Copper Cable.
10-Gigabit Small Form Factor Pluggables (XFPs) 3 In This Chapter 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Small Form Factor Pluggables (XFPs) are fiber-based optical transceivers. XFPs are fully hotswappable and are available for both short-reach and long-reach applications. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported XFP transceivers. For additional details about OmniSwitch modules, see the appropriate OmniSwitch Hardware Guide.
XFP MSA Specification The 10-Gigabit Small Form-Factor Pluggable (XFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The XFP connector consists of a 30-pin receptacle and an XFP housing cage. The connector provides the interface for the hot pluggable XFP module. Each XFP module contains a serial interface to provide identification information that describes the XFP capabilities, standard interfaces, manufacturer and other information.
10-Gigabit Small Form Factor Pluggables (XFPs) XFP Transceiver Installation and Removal XFP Transceiver Installation and Removal Follow the instructions below when installing an XFP transceiver. ESD Caution: Before handling the module, you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the chassis.
10-Gigabit Ethernet Transceivers 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers XFP-10G-SR 10-Gigabit XFP Optical Transceiver. Connector Type LC Standards Supported 802.3ae, XFP MSA Connections Supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.3 to -1.0 dBm Receiver Sensitivity -9.9 dBm Transmission Distance !"300 m (with OM3 fiber) Power Consumption 1.
10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers 10-Gigabit Ethernet Transceivers (cont.) XFP-10G-ER40 10-Gigabit XFP Optical Transceiver. Connector Type LC Standards Supported 802.3ae, XFP MSA Connections Supported 10GBase-ER Cable Type SMF Wavelength 1550 nm Optical Power Output -4.7 to +4 dBm Receiver Sensitivity -15.8 dBm Transmission Distance ! 40 km Power Consumption 3.5 W Max.
10-Gigabit Ethernet Transceivers 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers (cont.) XFP-10G-CX4 10-Gigabit XFP Copper Transceiver. Connector Type CX4 Standards Supported 802.3ak, XFP MSA Connections supported 10GBase-CX4 Cable Type Standard CX4 copper cables compliant with IEEE 802.3ak Transmission Distance !15 m Digital Diagnostic Monitoring Not Supported Notes InfiniBand type cables not supported.
10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers XFP-10G-DWDM Dense Wavelength Division Multiplexing (DWDM), 100GHz ITU Grid, C-Band optical transceiver supporting single-mode fiber over various wavelengths. DWDMs are hot-pluggable and are available for long-reach applications. Connector type LC Standards Supported XFP MSA Fiber Type SMF Wavelength Channel 35 - 1549.32 Channel 37 - 1547.72 Channel 38 - 1546.92 Channel 39 - 1546.12 Channel 59 - 1530.
OmniSwitch 6855 Series 4 SFP Compatibility Matrix SFP Compatibility Matrix OmniSwitch 6855 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6855: SFP OS6855 iSFP-GIG-SX 6.3.2 iSFP-GIG-LX 6.3.2 iSFP-GIG-LH40 6.3.2 iSFP-GIG-LH70 6.3.2 iSFP-GIG-EZX 6.4.5 iSFP-100-BX-D 1 iSFP-100-BX-U 1 6.3.2 6.3.2 1 6.4.2 iSFP-100-BXLC-U1 6.4.2 iSFP-100-BXLC-D iSFP-100-MM 1 6.3.2 iSFP-100-SM151 6.3.
SFP Compatibility Matrix OmniSwitch 6850E Series OmniSwitch 6850E Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6850E: SFP 6850E OS6850E-U24X (Excluding U24X) SFP-GIG-SX 6.4.4 6.4.4 SFP-GIG-LX 6.4.4 6.4.4 SFP-GIG-LH40 6.4.4 6.4.4 SFP-GIG-LH70 6.4.4 6.4.4 SFP-GIG-EXTND 6.4.4 6.4.4 SFP-GIG-CWD 6.4.4 6.4.4 SFP-GIG-T 1 Not Supported 6.4.4 SFP-GIG-EZX 6.4.5 6.4.5 SFP-DUAL-MM 6.4.5 6.4.
OmniSwitch 9000E Series SFP Compatibility Matrix OmniSwitch 9000E Series The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 9000E Series: SFP SFP-GIG-SX1 SFP-GIG-LX1 SFP-GIG-LH40 SFP-GIG-LH70 1 1 SFP-GIG-EXTND 1 OS9-GNI-U24E OS9-XNI-U12E 6.4.1 6.4.4 6.4.1 6.4.4 6.4.1 6.4.4 6.4.1 6.4.4 6.4.1 6.4.4 SFP-GIG-CWD1 6.4.1 6.4.4 SFP-GIG-T1,2 6.4.1 6.4.4 SFP-GIG-EZX 6.4.5 Not Supported SFP-DUAL-MM 6.4.
SFP Compatibility Matrix OmniSwitch 6400 Series OmniSwitch 6400 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6400: SFP OS6400 (All ports/All models) SFP-GIG-SX 6.3.3 SFP-GIG-LX 6.3.3 SFP-GIG-LH40 6.3.3 SFP-GIG-LH70 6.3.3 SFP-GIG-EXTND 6.3.3 Not Supported SFP-GIG-CWD SFP-GIG-T 1,2 6.3.3 6.4.5 SFP-GIG-EZX SFP-DUAL-MM Not Supported SFP-DUAL-SM10 Not Supported SFP-DUAL-BX-D 6.4.5 SFP-DUAL-BX-U 6.4.
OmniSwitch 9000E Series 5 XFP Compatibility Matrix XFP Compatibility Matrix OmniSwitch 9000E Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 9000E Series: XFP OS9-XNI-U2E XFP-10G-SR 6.4.1 XFP-10G-LR 6.4.1 XFP-10G-ER40 6.4.1 XFP-10G-ZR80 6.4.1 XFP-10G-CX4 6.4.1 XFP-10G-DWDM 6.4.
XFP Compatibility Matrix OmniSwitch 6400 Series OmniSwitch 6400 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6400: XFP No 10-Gig Support All OmniSwitch Transceivers Guide OmniSwitch 6400 January 2013 page 5-45
OmniSwitch 6400 Series page 5-46 XFP Compatibility Matrix OmniSwitch Transceivers Guide January 2013
