User guides

User Guide
F860 VOICE / F860 VOICE DUO /
F860 VOICE TRIO
This telephone is built-in with Smart Call Block feature*. This feature will help
you avoid nuisance calls by only allowing some numbers to make your phone
ring.
Default setting of Smart Call Block in this telephone is OFF but you can
enable it via your phone settings, as explained in the following paragraphs.
*This feature requires a subscription of Caller Line Identification service from your
telephone service provider.
Explanations
Call Block function (Block all call with numbers) is Disabled.
This is the default mode.
Call Block function is set to Manual. Numbers registered in the black
list will not go through and the phone will ring silently.
Numbers can be added to the list while the phone is ringing and / or
after a call (to enable, see part 1).
In this automatic mode, any number not registered to your
phonebook will be automatically be blocked and not cause your
phone to ring. All calls from contacts registered to your phonebook
will proceed normally.
When this mode is chosen, Contacts OK is displayed on LCD in idle
mode unless you have unread messages/ missed calls (to enable,
see part 2.1).
In this second automatic mode, only calls from contacts registered
as VIP in your phonebook will go through and cause your phone to
ring. Any other number will not ring. When this mode is chosen,
VIPS OK is displayed on the LCD in idle mode unless you have
unread messages / missed calls (to enable, see part 2.2).
This extra feature allows you to block call that do not have a
number attached to them (ie private calls, international calls, etc).
This option can be enabled on top of any of the previous four (to
enable, see part 3).
Setting
OFF
ON
CONTACTS
VIPS
ANONYMOUS
1. Manual call block mode
Manual call block is the easiest option when starting out. When you chose ON
in the call block settings, all calling numbers registered in your blacklist will
be blocked. You can add/remove numbers from that list at any time.
How to block an incoming call:
When the phone is ringing and before answering, press . It will terminate
the call and offer you the option to register the number to the blacklist in one
click.
Then to confirm the registration of this number in the blacklist, press .
IMPORTANT: if you don’t confirm, the number will not be added to
the blacklist and the next call will go through normally.
1.1. Enable MANUAL mode
MENU CALL BLOCK BLOCK SET. OFF
ON
VIP OK
CONTACTS OK
Press , press or to select Call Block
Press , press or to select Block set
Press , press or to select ON (manual mode)
OR
In idle mode, press to access BLOCK SET. directly.
After you enable this option, the call block icon will be displayed on the
LCD.
1.2. Add numbers to Blacklist
In idle mode,
1. Press key, BLOCK SET. is displayed, or
Press to press or to select CALL BLOCK, press to show
BLOCK SET.
2. Press or to select BLOCKLIST.
3. Press , press or to select ADD, enter number to be blocked,
press to save.
NOTE: 2 more ways to add incoming and outgoing call numbers in Block list:
1. From incoming call numbers
- Press , press or to select CALL LIST or press and hold .
- Press , press or to select call list entry.
- Press , press or to select to ADD to BLIST.
- Press to show selected number, press to save to Block list.
2. From outgoing call numbers
- Press , press or to select redial list entry.
- Press , press or to select to ADD to BLIST.
- Press to show selected number, press to save to Block list.
1.3. Edit numbers in Blacklist
In idle mode,
1. Repeat step 1 and 2 in Section 1.2.
2. Press , press or to select EDIT,
press or to select number to be edited, press to edit, and then
press to save.
Handset Overview
GETTING TO KNOW YOUR PHONE
1
In idle mode: Press to access the main menu
In sub-menu mode: Press to confirm the selection
During a call: Press to access Intercom/Phonebook/
Redial List/Call List
In main menu mode: Press to go back to idle screen
In sub-menu mode: Press to go back to previous level
In sub-menu mode: Press and hold to go back to idle screen
In editing/predialing mode: Press to clear a character/digit
In editing/predialing mode: Press and hold to delete all the
characters/digits
2
3
In idle mode: Press to access the call list
In menu mode: Press to scroll up the menu items
In Phonebook list/Redial list/Call List: Press to scroll up the list
During a call: Press to increase the volume
In ringing: Press to increase the ringer volume
In idle mode: Press to access the redial list
In menu mode: Press to scroll down the menu items
In Phonebook list/Redial list/Call list: Press to scroll down the list
During a call: Press to decrease the volume
In ringing: Press to decrease the ringer volume
4
5
During a call: Press to end a call and go back to idle screen
In menu/editing mode: Press to go back to previous menu
In idle mode: Press and hold to access the call list
6
* Subject to subscription and availability of the CLI service from the fixed
line operator.
During a call: Press and hold to insert a Flash (R)
7
0
In idle mode: Press and hold to access the redial list
8
DIRECT MEMORY KEYS
9
In idle mode / during a call: Press M1 or M2 to dial pre-recorded
number stored in direct mem
,
10
*
In idle mode: Direct access to the Call Block menu
During a call: Press to activate/deactivate the speaker mode
In idle / pre-dialing mode: Press to make a call
In Redial list / Call List / Phonebook entry: Press to make a call to the
selected entry in the list
During ringing: Press to answer a call
11
Base Station Overview
Press on the base station to page your handset. It will ring for
approximately 60 seconds
Press and hold on the base station for about five seconds, the base
station is entered into registration mode and allows handset registration
12
Increase (+) speaker volume during message playback
13
0F-> --
0n-> XX
00
XX
ZZ
XX/FF
FF
- -
When answering machine is OFF.
When answering machine is ON where XX is number of
messages in TAM memory.
Steadily ON: No voice messages in TAM.
Flash: There are XX new voice messages received.
Steadily ON: There are ZZ old voice messages kept in the
TAM memory (no new voice messages).
Flash XX alternatively with FF: There are XX new voice
messages received and the TAM memory is full.
Flash FF: TAM memory is full and there are no new messages,
only old messages are kept in TAM memory.
Flash - -: Time is not set and there are old voice messages
kept in the TAM memory only (no new voice messages)
DISPLAY
14
XX
A1/A2
Steadily ON: Playing the current XX incoming old message.
Flash: Playing the current XX incoming new message.
Steadily ON: Playing the current outgoing message
(OGM) where A1 is the Answer & Record OGM and A2 is the
Answer Only OGM.
XX
rA
LX
Flash XX alternatively with An: XX new incoming message is
now recording. An denotes that the incoming message
recording is in progress
Flash: Remote access is in progress.
Steadily ON: Indicate the current volume level where X is
from 1 to 8 (non-cyclic).
15
Press to turn on the answering machine.
Press again to turn off the answering machine.
Press to skip the current message and play the next message.
Press once to delete the current message.
Press and hold to delete all the messages.
Press to repeat playing the current message from the beginning.
Press twice to skip backward to the previous message.
CALL ALL
/ to save as VIP or to
save as CONTACT.
Notes:
- ! appears in the end of name of VIP entry.
- Phonebook is stored in base unit which is shared with duo, trio handsets.
ANSWERING MACHINE
Turn On/Off the Answering Machine
Set the Answer Mode
Record your own outgoing message (OGM)
Set the Answer Delay
Playback and Delete the Outgoing Message (OGM)
Settings through the Handset
USING THE PHONE
PHONEBOOK SETTINGS: 100 ENTRIES
GENERAL SETTINGS
Received and end a call
1. Press and or to select ANS. MACHINE.
2. Press and or to select TAM ON/OFF.
3. Press and or to select ON or OFF.
4. Press to confirm.
1. Press and or to select ANS. MACHINE.
2. Press and or to select TAM SETTINGS.
3. Press and or to select ANSWER MODE.
4. Press and or to select ANS & REC or ANSWER ONLY.
5. Press to confirm.
4. Available options: 2 - 8 RINGS or TIME SAVER.
5. Press to confirm.
1. Press and or to select ANS. MACHINE.
2. Press and or to select TAM SETTINGS.
3. Press and or to select OGM SETTINGS.
1. Press and or to select ANS. MACHINE.
2. Press and or to select TAM SETTINGS.
3. Press and or to select ANSWER DELAY.
1. Press and or to select ANS. MACHINE.
2. Press and or to select MSG PLAYBACK.
3. Press to start message playback.
5. Press and or to select RECORD MESS.
4. Press and or to select ANS & REC or ANSWER ONLY.
6. Press to start recording.
7. Press to stop recording.
Remote Access
To set Answer machine OFF
To set Answer machine ON
Delete the message
Skip the current message
(During playback)
To replay the current message
Repeat playing the current message from
the beginning
9
7
2
6
5
4
KeyAction
1. Dial your phone number.
2.
When you hear your outgoing message, press and enter your 4-digit
remote access PIN (master PIN 0000).
3. Follow the voice prompts as below:
4. During message playback, select and or if you’re happy with it
or you can delete.
Decrease (-) speaker volume during message playback.
16
Press to play the message.
Press again to stop the message playback.
17
18
19
20
Display Icons and Symbols
Indicates that the handset is registered and within range of the base
station
Icon blinks when the handset is out of range or is searching for a base
Indicates that an external call is connected or held
Displays when handsfree is activated
Indicates the battery is fully charged
Indicate when the battery is fully discharged
Indicates you have a new missed calls*
Indicates you have a new voice mail message*
Displays when the alarm clock is activated
Indicates when the answering machine (TAM) is turned on
Flashes when new TAM messages are received
Indicates that the Call Blocking function is activated
WELCOME FRANCE
CONFIRM? U.K.
CALL BLOCK OVERVIEW
- Connect plugs in corresponding sockets in the base station. Plug the
telephone line into telephone socket and insert power plug in an electrical
outlet.
- Insert batteries in Handset.
- After first time power up (base unit is connected to AC mains), welcome
mode (country) will appear on the screen (Fig.1).
Before you start to use your telephone, charge batteries continuously for 15
hours.
Use only plug adapter and rechargeable batteries supplied with your
phone.
BEFORE 1ST USE
Connecting your phone: