Specifications

Highly stable synthetic oil.
Perfluoropolyether.
- Highly inert to chemicals
- Pumping oxygen
- Plasma etching
67
Start-up
Table of recommended oils
Recommended oils
In the vane pumps, we recommend to use only the ALCATEL oils in the table
below:
* Ultimate pressure measured according to Pneurop 6602 specifications on 2015 ALCATEL pump.
These values are given as a rough guide only. They may vary according to the type of pump and the pumping conditions.
Requires special preparation of pump (see page 88).
Note: In this case, pump performances may be slightly different from those given in pages 59, 60, 61.
However, the following replacement fluids can be used:
Mineral oil:
ELF MOVIXA PV 100, TURBELF SA 100,
BP CS 100 (BP registered trademark)
SHELL VITREA 100 (SHELL registered trademark)
TOTAL CORTIS PV 100 (TOTAL registered trademark)
INLAND 19, INLAND 20 (INLAND registered trademark)
MR 200 (MATSUMURA registered trademark)
Mineral-based synthetic oils:
ELF BARELF F 100, ELF BARELF C 68 (ELF registered trademark)
INVOIL 20 (INLAND registered trademark)
INLAND TW (INLAND registered trademark)
ELITE Z (CAMBRIGE MILL PRODUCTS, INC. reg. trademark)
Ester type synthetic oils:
ANDEROL 555 (HÜLS registered trademark)
ANDEROL RCF 96 N (HÜLS registered trademark)
Fluorocarbon synthetic oils:
FOMBLIN YL VAC 25-6 (MONTEDISON registered trademark)
KRYTOX 15-25 (DU PONT DE NEMOURS registered trademark)
HALOVAC 100 (HALOCARBON registered trademark)
AFLUNOX 15.25 (SCM registered trademark)
APPLICATIONOIL
Anti-emulsion mineral oil
- Drying
- Pumping water vapour
- Freeze-drying
ALCATEL
102
Hydro-carbon based synthetic oil with good heat
resistance:
- Pumping at high pressures
- Operating at high ambient temperatures
ALCATEL
111
≤ 1.10
-2
40°C/100
100°C/7.8
ALCATEL
113
≤ 5.10
-3
40°C/90
100°C/11
Mineral oil distilled under vacuum:
- Pumping corrosive products
- Low backstreaming
ALCATEL
200
≤ 2.10
-2
40°C/58
100°C/8.5
Hydrocarbon-based mineral oil distilled under
vacuum:
Pumping corrosive products
- Plasma etching
- Operating at high temperatures
ALCATEL
300
≤ 5.10
-3
40°C/56
100°C/8.9
Total
ultimate
pressure*
(mbar)
General-purpose paraffin-based refined mineral oil
- Good ultimate pressure
- Low backstreaming
ALCATEL
120
≤ 2.10
-3
40°C/120
100°C/12.5
Mineral oil distilled under vacuum
- Pumping non-corrosive products
- Low viscosity
ALCATEL
119
≤ 3.10
-3
40°C/54
100°C/8.1
I SD C1
≤ 3.10
-2
< 1.10
-3
< 3.10
-5
< 1.10
-5
< 1.10
-5
Vapour
tension
25°C
(mbar)
< 4.10
-5
< 4.10
-5
212°C
245°C
none
none
223°C
259°C
243°C
270°C
Flash point/
self-ignition
temperature
260°C
295°C
213°C
244°C
230°C
260°C
40°C/98
100°C/11.1
Viscosity
mm
2
/s
(cst)
C2
Special hydrocarbon based mineral oil
ALCATEL
121
≤ 3.10
-3
40°C/64
100°C/10
< 1.33.10
-7
268°C
296°C
< 1.10
-3