SpeedTouch™ 600Series Business DSL Routers Orientation Guide Release R4.
SpeedTouch™610 Business DSL Router Orientation Guide Release R4.
Status Change Note Short Title Copyright Released PeckelbeenS AppNote ST610 Orientation Guide R4.2 (en) © 2003 THOMSON. All rights reserved. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON.
Contents E-SIT-CTC-20030306-0004 v2.0 1 SpeedTouch™610 Installation ...................................... 3 1.1 Get Acquainted with the SpeedTouch™610 .................................................... 4 1.2 SpeedTouch™610 Wiring ................................................................................... 8 1.3 SpeedTouch™610 Configuration Setup .......................................................... 10 1.3.1 Configuration Setup for Microsoft Windows Operating Systems ...............
2 4 SpeedTouch™610 Advanced Concepts ..................... 61 4.1 Native Command Line Interface Access......................................................... 62 4.2 Simple Network Management Protocol ......................................................... 64 4.3 Packet Firewalling.............................................................................................. 65 5 Troubleshooting ........................................................... 69 E-SIT-CTC-20030306-0004 v2.
1 SpeedTouch™610 Installation 1 SpeedTouch™610 Installation Introduction Thank you for purchasing the SpeedTouch™610 Business DSL router! Specially designed for Small/Medium Enterprises (SMEs) and Small Office/Home Office (SOHO), the SpeedTouch™610 Business Digital Subscriber Line (DSL) router offers plenty of capabilities. With an easy installation, embedded firewall, embedded IPSec based IP Virtual Private Networking (VPN) and remote management tools, the SpeedTouch™610 is a highly secure device.
1 SpeedTouch™610 Installation 1.1 Get Acquainted with the SpeedTouch™610 Delivery check Check your SpeedTouch™610 box for the following items: • The SpeedTouch™610/610i/610s/610v • One power adapter • One Cat.
1 SpeedTouch™610 Installation Front and back panel layout The SpeedTouch™610 is presented in a slim line housing: Depending on the SpeedTouch™610 model you purchased, the device can be equipped with: • One single 10/100Base-T Half-/Full-duplex MDI-X Ethernet port (optionally with one 25.6Mb/s ATM-Forum port): Power Switch 25.
1 SpeedTouch™610 Installation Front panel LEDs The SpeedTouch™610 is equipped with five LEDs on its front panel, indicating the state of the device during normal operation: Indicator Description Name Color State LAN Green Flashing Ethernet LAN activity Off No Ethernet LAN activity Flashing ATM cell transmission on DSL line Off No transmission activity Flashing ATM cell reception on DSL line Off No reception activity Flashing Initialization of DSL line On DSL line synchronized Green
1 SpeedTouch™610 Installation DSL variants Four DSL variants of the SpeedTouch™610 Business DSL routers exist: • The SpeedTouch™610: The ADSL/POTS variant connecting to an analog POTS(*) line. • The SpeedTouch™610i: The ADSL/ISDN variant connecting to a digital ISDN(**) line. • The SpeedTouch™610s: The SHDSL variant connecting to a dedicated SHDSL(***) line. • The SpeedTouch™610v: The SHDSL variant connecting to a dedicated VDSL(****) line.
1 SpeedTouch™610 Installation 1.2 SpeedTouch™610 Wiring Local network Ethernet Cables For Ethernet connectivity you need at least: • A computer with installed Ethernet Network Interface Card (NIC) • If needed, a hub or switch and the necessary connection cables In the SpeedTouch™610 box, a full wired Cat.5 straight-through RJ45/RJ45 Ethernet cable, further referred to as LAN cable is included. You can use LAN cables other than the one provided in the box.
1 SpeedTouch™610 Installation LAN wiring Powering E-SIT-CTC-20030306-0004 v2.0 Using the SpeedTouch™610 switch (if equipped) and/or an external hub you can connect multiple PCs to your SpeedTouch™610: Once all previous steps are completed, you can turn the SpeedTouch™610 on (I) with the power switch.
1 SpeedTouch™610 Installation 1.3 SpeedTouch™610 Configuration Setup Internet connectivity As soon as the SpeedTouch™610 is installed as described in “1.2 SpeedTouch™610 Wiring” on page 8 the SpeedTouch™610 can be prepared for Internet connectivity. The configuration of your SpeedTouch™610 can be done semi-automatically via the SpeedTouch™ Setup configuration files (available on the SpeedTouch™ Setup CD-ROM), or manually via its web pages.
1 SpeedTouch™610 Installation 1.3.1 Configuration Setup for Microsoft Windows Operating Systems Microsoft Windows TCP/IP One of the following operating systems must be installed on your PC(s): • Windows 98 • Windows 98SE • Windows ME • Windows NT4.0 SP6 • Windows 2000 • Windows XP Make sure that TCP/IP (*) is installed on your PC(s). (*) Transmission Control Protocol (TCP) / Internet Protocol (IP) The SpeedTouch™ Setup Wizard E-SIT-CTC-20030306-0004 v2.
1 SpeedTouch™610 Installation The detection procedure The detection procedure proceeds as follows: 1 Insert the SpeedTouch™ Setup CD-ROM in your PC's CD-ROM drive. The SpeedTouch™ CD Browser will start automatically. Note 2 If the SpeedTouch™ CD Browser window does not appear automatically, open a Run window via Start > Run from the Start menu and enter following path: D:\Menu.exe, where D is the drive letter of your CD-ROM drive.
1 SpeedTouch™610 Installation 4 The Setup and Installation window appears: To start the SpeedTouch™ Setup wizard, click Setup my SpeedTouch™. 5 The Welcome to the SpeedTouch™ Setup Wizard window appears: Click Next to proceed. 6 The Software License Agreement window appears: You must accept before continuing. Therefor click Yes to accept. Note E-SIT-CTC-20030306-0004 v2.0 If you have already accepted this License Agreement in a previous configuration setup, this window will not be shown.
1 SpeedTouch™610 Installation 7 The Setup wizard will continue to search for the SpeedTouch™610 on the network. The following window shows the detection progress: 8 The setup wizard should find your SpeedTouch™610 device on the local network. This is indicated by following window: In case more than one SpeedTouch™ device is found, a listing is provided from which you can select your SpeedTouch™610. Note If the wizard does not find a SpeedTouch™610 on the network, an error window appears.
1 SpeedTouch™610 Installation The configuration procedure The configuration procedure proceeds as follows: 1 As soon the wizard detected your SpeedTouch™610, some device details are shown. In case multiple SpeedTouch™ devices reside on your local LAN, a listing of devices is shown from which you can select the appropriate one. Click Next to proceed. Note 2 If the SpeedTouch™610 has been configured before: • It may be protected by a system password.
1 SpeedTouch™610 Installation 5 After restarting your PC, the SpeedTouch™ Setup wizard will appear again to announce that the configuration has been successful: Click Finish to close the wizard. Most configuration profiles will enable SpeedTouch™610’s DHCP server - and a PC’s Ethernet port is configured as DHCP client by default.
1 SpeedTouch™610 Installation 1.3.2 Configuration Setup for other Operating Systems Supported Operating Systems As the SpeedTouch™610 is OS-independent, this configuration setup can be used by any computer system. Note TCP/IP The following procedure may equally be used on MS Windows OSs. Ensure that your operating system has a valid TCP/IP configuration. Configure your computer with a static Net10 private IP address, e.g. 10.0.0.1, 10.0.0.2, etc. Ensure, however, that you do NOT use the 10.0.0.
1 SpeedTouch™610 Installation 4 The following window invites you to select the appropriate connection profile for your internet connectivity: In the Service list, click the connection profile of your choice. Note 18 You can add services to the Services list by uploading templates. See “ Templates” on page 56 for more information on uploading templates. 5 Subsequent screens guide you through the configuration setup of both your SpeedTouch™ and/or your PC.
1 SpeedTouch™610 Installation 7 The SpeedTouch™ Setup Wizard appears again to announce that the configuration has been successfully completed: Click Finish to close the wizard. 8 After the configuration is applied on the SpeedTouch™ some additional configuration of your computer system may be necessary. Note 9 To check whether the new configuration was successful, you can browse to the SpeedTouch™ and check its current status. Note E-SIT-CTC-20030306-0004 v2.
1 SpeedTouch™610 Installation 1.4 Dr. SpeedTouch™ Installation Introduction The Dr. SpeedTouch™ application allows you to diagnose and troubleshoot your SpeedTouch™610. With the Dr. SpeedTouch™ application you can do the following: Supported Operating Systems Installation procedure • View the status and performance of the SpeedTouch™ device • Run a Diagnostics program to locate a connectivity problem • Run a Troubleshooter to help you solve a connectivity problem. Installing and using Dr.
1 SpeedTouch™610 Installation Using Dr. SpeedTouch™ By default Dr. SpeedTouch™ is started automatically at boot of your system and runs in the background, i.e. minimized in the status area. To pop up Dr. SpeedTouch™: Dr. SpeedTouch™ features E-SIT-CTC-20030306-0004 v2.0 1 Double-click in the status area. 2 Dr. SpeedTouch™ searches your network for SpeedTouch™ devices. If more than one device is found, a list of available devices will be provided.
1 SpeedTouch™610 Installation • Monitor the downstream and upstream performance. of your DSL connection: • Test and troubleshoot the connectivity of your computer and the SpeedTouch™610 device to your ISP and the Internet via the Diagnostics wizard. Note 22 For more information on Dr. SpeedTouch™ please click Help in the application or press F1 context sensitive help. E-SIT-CTC-20030306-0004 v2.
2 SpeedTouch™610 Internet Connectivity 2 SpeedTouch™610 Internet Connectivity Introduction This chapter provides information on how to access the Internet and how to configure your SpeedTouch™ according to your preferences. Surfing the Internet As soon as the SpeedTouch™610 and the computer(s) have been configured as outlined in “1.3 SpeedTouch™610 Configuration Setup” on page 10, you can connect to the Internet.
2 SpeedTouch™610 Internet Connectivity 2.1 Connect to the Internet via SpeedTouch™’s embedded PPP Client Introduction The SpeedTouch™ supports both two most popular connection methods: Routed PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE). The connection method to use depends on the preferences of your ISP, hence the connection profile you must apply to the SpeedTouch™ via the SpeedTouch™ Setup wizard or its embedded Easy Setup wizard.
2 SpeedTouch™610 Internet Connectivity 2.1.1 Internet Sessions via Windows XP’s UPnP Starting an Internet session via Windows XP’s UPnP To connect to the internet via Windows XP’s Internet Connection icon proceed as follows: 1 Click Control Panel on the Start menu. 2 The Control Panel window appears. Double-click Network Connections. 3 The Network Connections window appears: Double-click the Internet Connection icon.
2 SpeedTouch™610 Internet Connectivity 2.1.2 Internet Sessions via the SpeedTouch™ Web Pages (all OSs) Starting a PPP session To open a Routed PPP connection proceed as follows: 1 Open a web browser on your computer and browse to the SpeedTouch™610 web pages: By default the SpeedTouch™610 offers you the System Information page. Terminating an active PPP session 26 2 In the Quick menu, click Connections to open the Connections page which enables you to establish dial-in connections.
3 The SpeedTouch™610 Web Interface 3 The SpeedTouch™610 Web Interface Introduction The SpeedTouch™610 comes with integrated local configuration capabilities. The local configuration via the SpeedTouch™610 web interface, is based on the HTTP server/web browser concept. It allows configuration of your SpeedTouch™610 via a Web browser through HTML pages from any local computer attached to the Ethernet interface(s).
3 The SpeedTouch™610 Web Interface 3.1 General Principles Access to the SpeedTouch™610 web interface Access to the SpeedTouch™610 web interface via UPnP To access the SpeedTouch™ web pages: 1 Start the web browser on your computer. 2 Browse to the SpeedTouch™610 at the SpeedTouch™610’s IP address (in most cases 10.0.0.138). 3 If a system password was set, an authentication window will be displayed. Enter user name and system password in the appropriate fields.
3 The SpeedTouch™610 Web Interface Result As a result the System Information page appears: From now on the SpeedTouch™610 acts as a web server sending HTML pages/forms at your request. You can fill out these pages/forms and submit them to the SpeedTouch™610. The latter scans the pages and performs the appropriate configurations. Topic menu and links On the left of each of the SpeedTouch™610 web pages a topics menu is provided.
3 The SpeedTouch™610 Web Interface The following table lists all IP Router Tasks Links: Click ... To ... IP Addresses View/configure the SpeedTouch™610 IP interfaces. IP Routing View/configure the SpeedTouch™610 IP router. RIP View/configure RIP services. NAPT View/configure static NAPT services. View/configure multi-NAT entries. Define a Default local server for inbound connectivity. Configure UPnP. IPSEC Policy View/configure IPSec based VPN services.
3 The SpeedTouch™610 Web Interface The following table lists all System Config Tasks Links: Click ... To ... System Password Set a system password. Upgrade Manage software and configuration. Add-On Manage software keys. SNTP View/configure SNTP services. Syslog View/configure Syslog services. The following table lists all Advanced Tasks Links: Save All Click ... To ... CLI Open the web based Command Line Interface. Templates View/upload templates.
3 The SpeedTouch™610 Web Interface 3.2 Quick Tasks Links Easy Setup Click this link to start the SpeedTouch™ Easy Setup wizard. See “1.3.2 Configuration Setup for other Operating Systems” on page 17 for more information. System Information Click this link to display the System Information page. This page is also the SpeedTouch™610 home page.
3 The SpeedTouch™610 Web Interface Connections • Click the configuration tab to view which configuration profile/file is currently loaded, including information for which Region and ISP this configuration applies: • Click the System tab to view some important system information of the SpeedTouch™: Click this link to view the Connections page. This page allows you to establish dial-in connections, if applicable: See “2.1.
3 The SpeedTouch™610 Web Interface Diagnostics Click this link to display the Diagnostics page. This page consists of three expandable sections: • Expand the System section to view some important system information: • Expand the Wan section. To view the current DSL state and connection information, expand the DSL and connections sections: Click • 34 to perform an IP connectivity test. Expand the Lan section to view the LAN configuration: E-SIT-CTC-20030306-0004 v2.
3 The SpeedTouch™610 Web Interface Syslog Click this link to display the Syslog page. This page allows you to: • View the syslog messages generated by the SpeedTouch™610: This page refreshes every 30 seconds. Via the CLI you can configure additional syslog events to be notified by syslog messages in addition to the standard set of syslog events. • Configure a computer IP address to send syslog messages to.
3 The SpeedTouch™610 Web Interface 3.3 IP Router Tasks Links IP Addresses Click this link to display the IP Addresses page. This page allows you to view or add/delete specific IP address entries for the SpeedTouch™610 interfaces: When adding an IP address, all essential IP routes will be automatically be added to the SpeedTouch™610 IP routing table. The eth0 interface allows you to assign an IP address to the SpeedTouch™ Ethernet interface. IP Routing Click this link to display the IP Routing page.
3 The SpeedTouch™610 Web Interface RIP Click this link to display the Routing Information Protocol (RIP) page. This page allows you to: • View or configure the SpeedTouch™610's general RIP configuration: Via the RIP Settings tab you can enable/disable the master RIP daemon and specify which RIP version should be used. Additionally you can set the default metric and some RIP timer settings.
3 The SpeedTouch™610 Web Interface NAPT Click this link to display the Network Address and Port Translation (NAPT) page. This page allows you to: • View or add/delete specific static NAPT entries: You can add static NAPT entries by 1 Click New. 2 Specify the outside address and inside address for the entry as well as the protocol and port on which the entry applies. Note 3 If the NAPT entry is applied to a connection’s dynamically assigned local peer IP address, you should specify 0.0.0.
3 The SpeedTouch™610 Web Interface • Define a default server: By specifying a default server IP address (e.g. 10.0.0.3 as depicted above), all incoming connections that don’t match a specifically configured static NAPT entry will be forwarded to the device with this IP address. In most cases this setting should be adequate for most server applications and eliminates the need for specific static NAPT entries.
3 The SpeedTouch™610 Web Interface IPSEC Policy To use the IP Security and IPSEC enabled VPN features of the SpeedTouch™610, the IPSec VPN software key must be installed. See the topic Add-On in the System Config Tasks Links for more information, or check the application note “SpeedTouch™610 Operation and Maintenance”. In case IPSec VPN is enabled, clicking this link will display IPSEC Policy Configuration page.
3 The SpeedTouch™610 Web Interface IPSEC Certificates Click this link to display the IPSEC Certificates Configuration page. In case certificates are used for authentication, this page allows you to view/configure the certificate configuration: The certificate configuration window contains four tabs, to view/configure: • Secure Storage. • Request-Import. • Certificate Revocation List (CRL). • Certificate Enrollment Protocol (CEP).
3 The SpeedTouch™610 Web Interface 3.4 Connection Tasks Links Phonebook Click this link to display the Phonebook page. This page allows you to view or add/delete ATM Virtual Channels (VCs), that are used for end-to-end connectivity over the DSL line via the Ethernet interface(s): For more information, see the application note “SpeedTouch™ Connection and Packet Services”. Routed Ethernet Click this link to display the Routed Ethernet Configuration page.
3 The SpeedTouch™610 Web Interface Routed PPPoE Click this link to display the Routed Point-to-Point Protocol over Ethernet (PPPoE) page. This page allows you to view/configure the SpeedTouch™610 Routed PPPoE connection entries Per selected Routed PPPoE you can: • Configure some advanced settings, if applicable: The destination of an Routed PPPoE should always be a Routed Ethernet interface or eth0 (PPPoE on the LAN) • E-SIT-CTC-20030306-0004 v2.
3 The SpeedTouch™610 Web Interface • Configure the service name and access concentrator, if applicable: • View some session statistics while a session is running on the selected Routed PPPoE entry: For more information, see the application notes “The SpeedTouch™ Routed PPPoE” and “The SpeedTouch™ PPPoE Relay”. 44 E-SIT-CTC-20030306-0004 v2.
3 The SpeedTouch™610 Web Interface Routed PPPoA Click this link to display the Routed Point-to-Point Protocol over ATM (PPPoA). This page allows you to: • View/configure the SpeedTouch™610 Routed PPPoA connection entries: For more information, see Routed PPPoE and the application note “The SpeedTouch™ Routed PPPoA”. Routed IPoA Click this link to display the Routed IP over ATM (IPoA) page. This page allows you to: • E-SIT-CTC-20030306-0004 v2.
3 The SpeedTouch™610 Web Interface Classical IP Click this link to display Classical IP (CIP) over ATM page. This page allows you to: Bridged Ethernet • View/configure the SpeedTouch™610 IP interface connection entries: • View/configure the SpeedTouch™610 CIP connection entries: Click this link to display the Bridged Ethernet page. Bridged Ethernet is commonly known as IEEE802.1D Transparent Bridging or RFC1483/Bridged.
3 The SpeedTouch™610 Web Interface 3.5 LAN Services Tasks Links DHCP Click this link to display the Dynamic Host Configuration Protocol (DHCP) page. In this page you can: • Click the DHCP Server tab to access the DHCP server pages. This page is subdivided into three parts: • Click the Server Config tab to enable/disable the SpeedTouch™610 (Auto)DHCP server: Under Properties you can select: • • DHCP server To enable the SpeedTouch™610 DHCP server.
3 The SpeedTouch™610 Web Interface • Click the Address Pools tab to configure the SpeedTouch™610 DHCP server lease pool properties: The SpeedTouch™610 DHCP server (if enabled) will use the address pools listed in this table to provide IP addresses to requesting DHCP clients. If needed, you can add/delete DHCP address pools manually. • Click the DHCP Relay tab to view the DHCP Relay pages.
3 The SpeedTouch™610 Web Interface • Click the DHCP client tab to view the current SpeedTouch™610 DHCP client status: Via this table you can also manually add static SpeedTouch™610 DHCP client entries for specific interfaces, if applicable. DNS Click this link to display the Dynamic Name System (DNS) page. This page allows you to: • View the current SpeedTouch™610 DNS server hostname leases: Via this table you can also add static DNS hostname entries.
3 The SpeedTouch™610 Web Interface SIP Click this link to display the Session Initiation Protocol (SIP) Proxy Server page. This page allows you to view/configure The SpeedTouch™610's integrated SIP multimedia PBX web page offers five tabs, allowing you to: • Configure the general SIP Settings of the SpeedTouch™610's SIP PBX. • Overview and add/delete SIP Users allowed to be involved in SIP communications. • Overview the Location Information for SIP users (i.e. Contact IP address).
3 The SpeedTouch™610 Web Interface 3.6 System Config Tasks Links System Password Click this link to display the System Setup page. This page allows you to configure a System password to restrict access to the SpeedTouch™610: It is highly advised to configure a System password. To protect the SpeedTouch™610 you should change the System password on a regular basis. However, never use an obvious password as your name, birth date, etc.
3 The SpeedTouch™610 Web Interface • Backup the current SpeedTouch™610 configuration, restore the SpeedTouch™610 factory defaults, or upload a new configuration file: To backup the current configuration, click Backup and follow the instructions. To restore the SpeedTouch™610 defaults, click Restore Defaults to load the default configuration and Restart to reboot the SpeedTouch™610 and allow the changes to take effect.
3 The SpeedTouch™610 Web Interface Add-On Click this link to display the Software Activation Key page. Next to the SpeedTouch™610 standard functionality additional software modules can be activated via this page. This page allows to: • View the current Software module Status: • Install a Software Activation Key. Therefore: 1 Follow the link of the appropriate software module you intend to activate to the SpeedTouch™ software activation key web server.
3 The SpeedTouch™610 Web Interface SNTP Click this link to display the Simple Network Time Protocol (SNTP) page. This page allows you to: • Configure an NTP server on the Internet to which the SpeedTouch™610 is able to synchronize its internal clock: You can check on the Internet for available NTP time servers. • View and/or set the time manually, in case external synchronization is not used: For more information, see the application note “SpeedTouch™610 Operation and Maintenance”.
3 The SpeedTouch™610 Web Interface 3.7 Advanced Tasks Links CLI Click this link to display the SpeedTouch™ Command Line Interface (CLI) page: The CLI is meant for in depth configuration of the SpeedTouch™610, giving full control on all configurational aspects of the device. The web based CLI provides the same functionality as the native Command Line Interface, available through a Telnet session to the SpeedTouch™610, or via the serial Console interface. All CLI groups and commands are placed in a menu.
3 The SpeedTouch™610 Web Interface Templates Click this link to display the Configuration Templates page. This page allows you to: • View the templates available for the embedded Easy Setup wizard: • Upload new template files, e.g. from the SpeedTouch™ Setup CD-ROM (usually template files have the extension .tpl): By uploading templates you can extend the number of services listed in the Easy Setup wizard. For more information, see the application note “The SpeedTouch™ Operation and Maintenance”.
3 The SpeedTouch™610 Web Interface 3.8 SpeedTouch™ NAPT Manager Introduction Using SpeedTouch™ NAPT Manager The SpeedTouch™ NAPT Manager allows you to add static NAT entries for specific applications. To add a static NAT entry using SpeedTouch™ NAPT Manager: 1 Insert the SpeedTouch™ Setup CD-ROM in your computer’s CD-ROM drive. The SpeedTouch™ CD Browser will start automatically. Select your language in the Choose Language window and go to Configuration > Configure NAT Settings.
3 The SpeedTouch™610 Web Interface 4 The Add Port Mapping window appears. If you want to: • Enter a port mapping for a specific application, click the Basic tab. Select an application in the Application list and enter a host IP address. By default, the IP address of the PC from where you are running NAPT Manager will be taken as host IP address. To add a NAPT entry for another PC you have to change the proposed IP address. • Manually add a static NAPT entry, click the Advanced tab.
3 The SpeedTouch™610 Web Interface 6 NAPT Manager saves the new NAPT entries to persistent memory: 7 At the end of the procedure the following window appears: Click Finish to quit NAPT Manager. E-SIT-CTC-20030306-0004 v2.
3 The SpeedTouch™610 Web Interface 60 E-SIT-CTC-20030306-0004 v2.
4 SpeedTouch™610 Advanced Concepts 4 SpeedTouch™610 Advanced Concepts Introduction Overview E-SIT-CTC-20030306-0004 v2.0 This chapter is intended to introduce some advanced features the SpeedTouch™610 supports.
4 SpeedTouch™610 Advanced Concepts 4.1 Native Command Line Interface Access Accessing the Command Line Interface The SpeedTouch™610 provides two methods for accessing its Command Line Interface: • Via a TCP/IP Telnet session • Via the serial “Console” interface. Note Basic CLI For both access methods, authentication is required in case the SpeedTouch™610 is protected by a system password.
4 SpeedTouch™610 Advanced Concepts Semi-graphical CLI To use the semi-graphical Command Line Interface, execute 'menu' from the prompt: The semi-graphical CLI offers you an attractive and easy-to-use configuration environment for the CLI. You can browse through the CLI command groups via the arrow keys. Pressing Enter executes your selection. From each level you can execute '..' to go one level up. Use the Tab key to change from the CLI command menu to the control menu and vice versa.
4 SpeedTouch™610 Advanced Concepts 4.2 Simple Network Management Protocol Introduction SpeedTouch™610 Firewall configuration The Simple Network Management Protocol (SNMP) is a standard way to retrieve counters, status variables and other diagnostic information of the SpeedTouch™610. The SpeedTouch™610 Firewall is configured to count the SNMP packets by default. To allow SNMP traffic to migrate to a remote SNMP manager, you will have to allow it explicitly by adding the appropriate firewall rules.
4 SpeedTouch™610 Advanced Concepts 4.3 Packet Firewalling Introduction A firewall is a security gateway that controls access between a private LAN domain, often referred to as Intranet (even for one computer), and the public Internet. It secures the entry points to the network in such way that access is only allowed to authorized traffic. Therefore, to effectively control the flow of data, firewall protection should be placed at each point where the network connects to the WAN.
4 SpeedTouch™610 Advanced Concepts • Source The point of all traffic sourced by the SpeedTouch™ IP router, i.e. at this point it can be determined whether a packet is allowed to leave the local IP host. • Output The point of all outgoing traffic, i.e. at this point it can be determined whether a packet is allowed to leave the SpeedTouch™610 IP router or local IP host.
4 SpeedTouch™610 Advanced Concepts Firewall treatments Once a packet is intercepted in a hook, and a (first) rule is found to be applicable (i.e. matches against at least one of the criteria defined in this rule), the SpeedTouch™610 firewall is able to: • Accept the packet I.e. submit it to the next processing stage without further action. • Deny the packet I.e. no submission is done and a message is sent to the sender that the packet could not be delivered. • Drop the packet I.e.
4 SpeedTouch™610 Advanced Concepts 68 E-SIT-CTC-20030306-0004 v2.
5 Troubleshooting 5 Troubleshooting Introduction This chapter provides information on how to identify and correct some common problems you may encounter when using and configuring the SpeedTouch™610. If the following troubleshooting tips have not resolved the problem contact the company from which you purchased the SpeedTouch™610 for assistance.
5 Troubleshooting Problem Solution Poor SpeedTouch™ performance. Make sure the SpeedTouch™ is installed as instructed in this User's Guide and/or as instructed by the SP. In case of ADSL service, check whether a central splitter or dedicated filters are installed properly. In case of SHDSL service, make sure no central splitter or dedicated filters are installed. No UPnP. Make sure UPnP is installed on your PC if you are running Microsoft Windows XP.
5 Troubleshooting How to perform a hardware reset to factory defaults Proceed as follows: 1 Put DIP switch number 4 in the UP position: Config Console You will notice that the PWR/Alarm LED flashes red. 2 Power cycle the SpeedTouch™610 and wait to allow it to restart. The SpeedTouch™610 will come online with manufacturing defaults. 3 Reset the DIP switch in its original position. If not, the PWR/Alarm LED will flash red as a warning.
5 Troubleshooting 72 E-SIT-CTC-20030306-0004 v2.
© 2003 THOMSON. All rights reserved. E-SIT-CTC-20030306-0004 v2.0 TCM3572299A www.speedtouch.
