Datasheet

Alcatel-Lucent Page 65
OmniSwitch 9000
Connector type 10/1000/1000BASE-T copper ports without PoE: RJ-45
10/100/1000BASE-T copper ports with PoE: RJ-45
Dual Speed 100BASE-FX or 1000BASE-X SFP ports: LC w/ Removable/Pluggable trans. SFP-MSA
CWDM SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
1000BASE-X SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
1000BASE-T SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
10GBASE-X XFP ports: LC with Removable/Pluggable XFP-MSA transceiver
Please refer to “Supported Configuration Matrix for New Ethernet Transceivers in Release 6.1.3r01”
Connectivity All modules are hot swappable and can be used in any available NI slot.
10/1000/1000BASE-T copper ports: RJ-45
10/100/1000BASE-T copper ports with PoE: RJ-45
100BASE-FX or 1000BASE-X SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
CWDM SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
1000BASE-X SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
1000BASE-T SFP ports: LC with Removable/Pluggable transceiver – SFP-MSA
10GBASE-X XFP ports: LC with Removable/Pluggable XFP-MSA transceiver
Connections supported CWDM Gigabit Ethernet
Dual Speed 100BASE-FX or 1000BASE-X SFP ports
10BASE-T hub or device; 100BASE-TX hub or device; 1000BASE-T hub or device
1000BASE-X hub or device, and 10GBASE-X hub or device
Cable supported CWDM Gigabit Ethernet, Dual Speed 100BASE-FX or 1000BASE-X, 1000BASE-X,
and 10GBASE-X: Optical Fiber
10BASE-T: unshielded twisted-pair (UTP)
100BASE-TX: unshielded twisted-pair (UTP), Category 5, EIA/TIA 568 or shielded twisted-pair
(STP), Category 5, 100 ohm
1000BASE-T: unshielded twisted-pair (UTP), Category 5/5e, EIA/TIA 568 or shielded twisted-pair
(STP), Category 5, 100 ohm
Note: Category 6 cabling is also supported on the 10/100/1000BASE-T connections.
Maximum cable distance On 10/100/1000Mbps triple speed copper ports:
10Mbps speed: 100 meters on copper
100Mbps speed: 100 meters on copper
1000Mbps speed: 100 meters on copper
On GigE. Fiber ports:
SFP-GIG-xCWD60: up to 60km on 9/125µm SMF
SFP-GIG-LH40: up to 40km on 9/125µm SMF
SFP-GIG-LH70: up to 70km on 9/125µm SMF
SFP-GIG-LX: 10km on 9/125µm SMF & typical reach of 550m on 50/125 & 62.5/125µm MMF.
SFP-GIG-SX: up to 550m on 50/125 & 62.5/125µm MMF
SFP-GIG-T: up to 100m on copper
Dual Speed Fiber ports:
SFP-DUAL-MM: 550m @Gigabit speeds and 2km @100Mbps speeds - MMF
SFP-DUAL-SM10: 10km @Gigabit speeds and @100Mbps speeds - SMF
On 10GigE. Fiber ports:
• XFP-10G-SR: up to 300 m (high modal bandwidth fiber is required to reach 300 meters)
• XFP-10G-LR: up to 10 km
• XFP-10G-ER40: up to 40km
• XFP-10G-ZR80: up to 80km
IEEE Standards Supported IEEE 802.3 Carrier Sense Multiple Access with Collision Detection (CSMA/CD)
Data rates
• Dual Speed 100Mbps or Gigabit speeds (Dual Speed 100BASE-FX or 1000BASE-X)
• 10/100/1000Mbps triple speed
o 10Mbps
o 100Mbps
o 1000Mbps (Gigabit Ethernet)
• Gigabit Ethernet
• 10000Mbps (10-Gigabit Ethernet)
Ports Supported 4.2.9
• Dual Speed 100Mbps or Gigabit speeds (Dual Speed 100BASE-FX or 1000BASE-X)
• Triple Speed ports is supported and includes:
o Ethernet (10 Mbps)
o Fast Ethernet (100 Mbps)
o 1000Mbps Ethernet (Gigabit Ethernet)
• Gigabit Ethernet
• 10-Gigabit Ethernet
Switching/Routing Support Layer 2 Switching/Layer 3 Routing
Backbone Support 100Mbps/1000Mbps, 10/100/1000Mbps, Gigabit Ethernet ports, and 10-Gigabit Ethernet ports
Port Mirroring Support 100Mbps/1000Mbps, 10/100/1000Mbps, Gigabit Ethernet ports, and 10-Gigabit Ethernet ports
802.1Q Hardware Tagging 100/1000Mbps, 10/100/1000Mbps, Gigabit Ethernet ports, and 10-Gigabit Ethernet ports
Maximum Transfer Unit -- MTU
The ASIC does not include the notion of an MTU that applies to an IP interface. Instead, it uses the