Datasheet

Alcatel-Lucent Page 61
OmniSwitch 9000
• CMM fabric status (FABRIC)
• Chassis ambient air temperature (TEMP)
• Fan status (FAN)
• Power Supply Unit (PSU) status (PSU)
• Ethernet management port (LINK and ACT)
Component LEDs Following a successful boot, the LEDs on all switch components, including power supplies, should
display as follows:
CMM OK1: Solid Green
CMM OK2: Blinking Green
CMM CONTROL: Solid Green
CMM FABRIC: Solid Green
CMM FAN: Solid Green
CMM TEMP Green
CMM PSU Green
NI OK1: Solid Green
NI OK2: Blinking Green
Power Supply AC OK: Solid Green
Power Supply DC OK: Solid Green
Power Supply OVER TEMP: Off
NI Modules Installation NI modules may be installed in any slot position from 1 through 16 in OS9800 switches, from 1
through 8 in OS9700 switches and 1 through 4 OS9600 switches.
OS9-GNI-C24 Module
(10/100/1000BASE-T module)
• This module supports 24 x 10/100/1000BASE-T (10/100/1000Mbps) RJ45 ports.
Each copper port is capable of auto-MDI/MDI-X sensing. The 10/100/1000BASE-T ports will operate
in full/half duplex mode when the speed is 10/100Mbps. When operating in 1,000 Mbps only full
duplex mode is supported.
OS9-GNI-C24 Module LEDs
(10/100/1000BASE-T module)
OK1: Hardware Status. Displays solid green when powered on and the GNI has passed hardware
diagnostic tests. Displays solid amber when powered on and the GNI has failed diagnostic testes.
OK2: Software Status. Blinks green when the GNI is operational and has successfully loaded software.
Displays solid amber when powered on and the GNI has failed to load the software.
PoE: PoE Status. This LED will be off if PoE is not available on this module and will be solid green if
PoE is enabled on this module.
Ethernet port LEDs:
Each Gigabit Ethernet port has two built-in corresponding LEDs. The top LED indicates 10/100Mbps
link and activity status for the port while the bottom LED indicates 1 Gigabit link and activity status
for the port.
The appropriate LED displays solid green when a valid Ethernet cable connection exists and there is no
PoE. Flashes green as data is transmitted or received on the port and there is no PoE.
If PoE is present, the appropriate LED displays solid amber when a valid Ethernet cable connection
exists. And flashes amber as data is transmitted or received on the port if PoE is present.
OS9-GNI-U24 Module
(1000BASE-X module)
• This module supports 24 x 1000BASE-X (Gigabit Ethernet) SFP MSA fiber optics ports.
The transceiver ports support full duplex mode only.
OS9-GNI-U24 Module LEDs OK1: Hardware Status. Displays solid green when powered on and the GNI has passed hardware
diagnostic tests. Displays solid amber when powered on and the GNI has failed diagnostic testes.
OK2: Software Status. Blinks green when the GNI is operational and has successfully loaded software.
Displays solid amber when powered on and the GNI has failed to load the software.
Gigabit Ethernet port LEDs:
Each fiber-based Gigabit Ethernet port has a corresponding LED. This LED indicates the link and
activity status for each Gigabit Ethernet port. The LED displays green when a valid Gigabit Ethernet
cable connection exists. Flashes green as data is transmitted or received on the port.
OS9-GNI-P24 Module
(10/100/1000BASE-T module with PoE)
This module supports 24 x 10/100/1000BASE-T (10/100/1000Mbps) RJ45 ports with PoE (IEEE
802.3af). Each copper port is capable of auto-MDI/MDI-X sensing, twisted-pair Power over Ethernet
(PoE) ports, individually configurable as 10Base-T, 100Base-TX, or 1000Base-T.
The 10/100/1000BASE-T ports will operate in full/half duplex mode when the speed is 10/100Mbps.
When operating in 1,000 Mbps only full duplex mode is supported.
OS9-GNI-P24 Module LEDs
(10/100/1000BASE-T module with PoE)
OK1: Hardware Status. Displays solid green when powered on and the GNI has passed hardware
diagnostic tests. Displays solid amber when powered on and the GNI has failed diagnostic testes.
OK2: Software Status. Blinks green when the GNI is operational and has successfully loaded software.
Displays solid amber when powered on and the GNI has failed to load the software.
PoE: PoE Status. This LED will be off if PoE is not available on this module and will be solid green if
PoE is enabled on this module.
Ethernet port LEDs:
Each Gigabit Ethernet port has two built-in corresponding LEDs. The top LED indicates 10/100Mbps
link and activity status for the port while the bottom LED indicates 1 Gigabit link and activity status
for the port.
The appropriate LED displays solid green when a valid Ethernet cable connection exists and there is no
PoE. Flashes green as data is transmitted or received on the port and there is no PoE.
If PoE is present, the appropriate LED displays solid amber when a valid Ethernet cable connection
exists. And flashes amber as data is transmitted or received on the port if PoE is present.