Datasheet

Alcatel-Lucent Page 35
OmniSwitch 9000
X
X
N
N
I
I
M
M
o
o
d
d
u
u
l
l
e
e
s
s
OmniSwitch 9000 Series 10 Gigabit Network Interface (XNI) modules provide up to six 10000 Mbps (10Gbps)
connections per module. In addition, XNI modules can be used in enterprise applications including backbone connections
in networks where 10 Gigabit Ethernet is used as the backbone media. XNI modules are supported during CMM failover.
The following wire-rate 10Gbps XNI modules are available:
• OS9-XNI-U2. Provides two XFP slots:
The OS9-XNI-U2 module provides two XFP slots. An XFP is a 10Gbps small-form, factor-Pluggable, module that is hot
Pluggable; i.e., it can be installed or removed while the XNI is powered on and operating without the risk of damage to the
XFP module or the host circuitry.
• OS9-XNI-U6. Provides six XFP slots:
The OS9-XNI-U6 module provides six XFP slots. An XFP is a 10Gbps small-form, factor-Pluggable, module that is hot
Pluggable; i.e., it can be installed or removed while the XNI is powered on and operating without the risk of damage to the
XFP module or the host circuitry.
OS9-XNI-U2 Technical Specifications Overview
OS9-XNI-U2 Technical Specifications Overview
Number of XFP ports
2 x 10GBASE-X slots
Connector types
LC
Standards supported
IEEE 802.3ae & 10-Gigabit Ethernet for 10GBASE-SR/-LR/-ER/-ZR
Data rate
10 Gigabit per second (full duplex)
Maximum frame size
9,216 bytes. OS9-XNI-U2 modules support jumbo frames (1,500 to 9,216 bytes)
MAC addresses supported
There are now two source learning modes available for the OmniSwitch 9000 Series switches: synchronized
and distributed. By default the switch runs in the synchronized mode, which allows a total MAC address tables
size of 16K per chassis. Enabling the distributed mode for the switch increases the table size to 16K per module
and up to 64K or more per OmniSwitch 9000 chassis.
The 6.1.3.R01 release provides support for this feature on the OmniSwitch 9000 Series.
Connections supported
10GBASE-S, 10GBASE-L, 10GBASE-E and 10GBASE-Z over LAN Phy.
Fiber optic cables supported
Multimode (62.5 and 50 µm ) and single mode
Power Budget
XFP-10G-SR: 7.3 dB
XFP-10G-LR: 9.4 dB
XFP-10G-ER40:
XFP-10G-ZR80:
Output optical power
XFP-10G-SR: -7.3 dBm (minimum)
XFP-10G-LR: -8.2 to 0.5 dBm
XFP-10G-ER40:
XFP-10G-ZR80:
Input optical power
XFP-10G-SR: -9.9 to -1.0 dBm
XFP-10G-LR: -14.4 to 0.5 dBm
XFP-10G-ER40:
XFP-10G-ZR80:
Cable Distances
XFP-10G-SR: 300 m (high modal bandwidth fiber is required to reach 300 meters)
XFP-10G-LR: 10 km
XFP-10G-ER40: 40 km
XFP-10G-ZR80: 80 km
Power
36watts
10-Gigabit Ethernet Transceivers (XFP MSA)
XFP-10G-ER40
10 Gigabit Ethernet optical transceiver (XFP MSA). Supports single mode fiber over 1550nm wavelength (nominal) with an
LC connector. Typical reach of 40 Km on 9/125 µm SMF.
XFP-10G-LR
10 Gigabit Ethernet optical transceiver (XFP MSA). Supports single mode fiber over 1310nm wavelength (nominal) with an
LC connector. Typical reach of 10 Km on 9/125 µm SMF.
[Formerly known as 10G-XFP-LR]
XFP-10G-SR
10 Gigabit Ethernet optical transceiver (XFP MSA). Supports multimode fiber over 850nm wavelength (nominal) with an LC
connector. Typical reach of 300m on 50/125 µm MMF.
[Formerly known as 10G-XFP-SR]
XFP-10G-ZR80
10 Gigabit Ethernet optical transceiver (XFP MSA). Supports single mode fiber over 1550nm wavelength (nominal) with an
LC connector. Typical reach of 80 Km on 9/125 µm SMF.