Datasheet

Alcatel-Lucent Page 23
OmniSwitch 9000
SFP MSA Specifications
• SFP-MSA Connector: The SFP connector consists of a 20-pin receptacle and a SFP housing cage. The 20-pin connector provides the
interface for the hot Pluggable SFP module. Each SFP module contains a serial interface to provide identification information that
describes the SFP capabilities, standard interfaces, manufacturer and other information.
• LC Connector: The LC connector is a fiber-optic cable connector that uses one-half the size of current industry standards. It
increases panel density and provides duplex connection in 50% less space with duplex fits of RJ-45 footprint. It is available in SM,
MM versions with Super, Ultra and Angle (APC) polishing. It provides a user-friendly audible latch to indicate proper mating and
supports pull – proof.
Notes:
• *The worst-case Optical Power Budget in “dB” for a fiber optic link is determined by:
The difference between the minimum transmitters output optical power and the lowest receiver sensitivity.
• **Maximum distance support” is claimed by the original vendor and not by Alcatel.Lucent IP Networking.
• Alcatel.Lucent switching & routing platforms support alternate sources of fiber-optics vendors, which are subject to change from
time to time. Please be sure to contact Alcatel.Lucent Internetworking Product Marketing for a complete list of approved vendors.
• The following fiber optics transceivers specifications have been taken from Alcatel.Lucent IP Networking approved vendor’s original
Specification Sheets.
SFP-GIG-SX Technical Specifications
Features Dual data-rate of 1.25Gbps/1.0625Gbps operation
850nm VCSEL laser and PIN photo detector
550m transmission with 50/125µm MMF
275m transmission with 62.5/125µm MMF
Standard serial ID information Compatible with SFP MSA
SFP MSA package with duplex LC connector
With Spring-Latch for high density application
Very low EMI and excellent ESD protection
+3.3V single power supply
Operating case temperature: 0 to +70°C
Connector Type The transceiver support LC connectors and are hot swappable
Supports the ability to mix and match SFPs on the same unit
Supports operation for layer-2, and layer-3 forwarding
Standards supported IEEE 802.3z, and 1000BASE-SX
(The IEEE 802.3z standard describes the specifications for the 1000BASE-X fiber optic GigE)
Compatible with SFP MSA
Compatible with IEEE 802.3z
Compatible with ANSI specifications for Fiber Channel
Compatible with FCC 47 CFR Part 15,Class B
Connections supported 1000BASE-SX connections to backbone or server
Fiber optic cable supported Multimode (MMF) with 62.5/125µm & 50/125µm
Wavelength 850nm (typical)
Transmitter Average Output Optical Power Min: -9.5 dBm and Max: -4 dBm
Receiver Sensitivity Min: 0 dBm and Max: -17 dBm
Power Budget* 7.5 dBm (17 – 9.5 = 7.5 dBm)
Cable distances** ≈ Supports 62.5/125µm MMF up to a maximum distance of 220 m to 300m or 50.0/125µm up to
a maximum distance of 550m.
SFP-GIG-LX Technical Specifications
Features Dual data-rate of 1.25Gbps/1.0625Gbps operation
1310nm FP laser and PIN photo detector
550m transmission with MMF
10km ~ 20km transmission with SMF
Standard serial ID information compatible with SFP MSA
SFP MSA package with duplex LC connector
With Spring-Latch for high density application
Very low EMI and excellent ESD protection
+3.3V single power supply
Operating case temperature:
Standard: 0 to +70°C
Industrial: -40 to +85°C
Connector Type The transceiver support LC connectors and are hot swappable
Supports the ability to mix and match SFPs on the same unit
Supports operation for layer-2, and layer-3 forwarding
Standards supported IEEE 802.3z, 1000BASE-LX
(The IEEE 802.3z standard describes the specifications for the 1000BASE-X fiber optic Gig Eth.)
Compatible with SFP MSA
Compatible with IEEE 802.3z